Having problems with your Dishwashers ?

Error code e4 flashes on belling dishwasher idw604 , washer is empty cant get any programs to work


Answers :

I found the solution myself. Underneath the machine, there is a plate. \015\012On the plate, there is a float and a\015\012 microswitch, when the water leaks onto the bottom plate it raises the \015\012float and activates the microswith which shuts down the machine and \015\012shows E4 on display. To get rid of the fault, you have to pull out the \015\012dishwasher, then tilt it, and drain the water from the bottom plate. \015\012Also make sure that \015\012there is no leak in the internal piping, if there is, the fault will \015\012come back as soon as the recess in the bottom panel fills with \015\012water.Hope it helps.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Error code e4 flashes on belling dishwasher idw604 , washer is empty cant get any programs to work


I found the solution myself. Underneath the machine, there is a plate. \015\012On the plate, there is a float and a\015\012 microswitch, when the water leaks onto the bottom plate it raises the \015\012float and activates the microswith which shuts d ... Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

I have a Kenmore Ultra Wash model 16879. After setting the dishwasher and going to bed I woke up to find the "Quick Rinse" light flashing. I am unable to get the light to stop or washer to work. I tried some of the "code" combinations I saw offered on fixya but I do not have a heated dry button, and cannot find another combo that works. Thank you for any tips you can provide.


1) Crack the door open.2) Within 3 seconds press the \015\012following sequence - Hi Temp Scrub, Energy Saver Dry, Hi Temp Scrub, Energy \015\012Saver Dry3) Close and latch the door4) \015\012Press the cancel button (the circle with ... Dishwashers

We have a candy integrated CDI 1012 dishwasher. After a program has been selected and the door closed. washer sounds as if it will work , but does not sound as though much water going in.The very quickly empties, then a peeping noise sounds. On opening the door the pots are dry , very little water inside, LED light flashing.


... Dishwashers

Water fills washer, program stops, inlet/drain flashes. checked all filters and pumps for blockages. none found. try again and washer empties water, then fills up again, program stops, inlet/drain flashes again. could it be a fuse???


Could it be.Try to open and look the fuse inside.Opps try to see the warranty of applian. ... Miele 24 in. G692SC Plus SS Free-standing Dishwasher

My electrolux dish washer model eidw6105gso stopped before it completed the cycle. All the selection lights were flashing and i could not get any functions to change. I killed the power at the breaker to try to reset and that didn't work either. I removed the panel on the front on the bottom to see if there was a reset button and found another display that is showing a light on the turbidity location. what is this and what might i do to get my washer back working?


... Electrolux Dishwashers

ASKO d 3122.. Keeps filling up the overflow area on the bottom of dishwasher. WHich sets of the overflow switch, then i get the flashing tea cup again. I will empty the over flow area. It will reset, We get one good wash out of it then on the next load it will stop work ing again and get the flashing Tea cup again, Back to unplugging the unit and draining the overflow area again.


... Dishwashers

Have a Kenmore Freestanding Dishwasher that was working when hooked up to the sink. When we plumbed it in and connected the electrical directly, we now get an "F4" flashing on the panel with a beeping noise and the pump sounds like it wants to drain but just get a sucking noise. I've tried putting water in it to prime the pump, but still doesn't want to work. Do the codes mean anything, or point to a specific part?


... Kenmore 24 in. 16332 / 16334 / 16339 Free-standing Dishwasher

Smeg Dishwasher Hello I have a smeg dishwasher - built in, push button. It has stopped working - the program start and you hear it drain but that's as far as it gets, no water appears to be getting in. A couple of times the last 2 program buttons flash or the rinse light is on when we open it. let me know if you have any thoughts on this - I'd really appreciate it. thanks Diane


Replace the timer/control board ... Dishwashers

I am having trouble attaching 90 degree brass elbow to the plastic water inlet on my new Maytag Dishwasher. Getting leaks. Teflon tape hasn't worked. Cant seem to get the washer to seat properly when everything is tightened down. Wish the water inlet was not made of plastic. It appears it would seat the gasket properly if the water inlet was made of something more durable.


Hi!!\015\012\015\012Have you tried pipe cement, the plastic to metal kind will take care of any leaks. You can find it at any hardware store.\015\012\015\012Good luck! A HELPFUL - 4 THUMBS - rating for this solution would be greatly app ... Maytag MDB8959AWS Builtin Dishwasher

I accidentally put Mr. Clean in my dishwasher where the Jet Dry is supposed to go. How do I get it out? i ran the washer and it began to foam up so the washer stopped and is flashing a repeating code HE then CL. Help!


... LG Dishwashers

I have a kenmore DW model 16019. The clean Light stays on the light does not turn off. I have tried to disconnect and have taken the motort apart to make sure everything is clean. What Can I do to solve this problem? 1. Does the washer work at all? No it does not work 2. Does it display any codes or flashing lights other than the CLEAN LIGHT being lit? no other lights are on except for the green blinking light 3. Is the light solid or blinking? blinking Green light 4. Entire model # is necessary


Thanks for re-posting with all the info!!The model # is 665.16019403The cleaning light blinking is a fault code listed in the tech. service sheet, its usually a faulty heating circuit.The sheet can be found behind the ki ... Kenmore Dishwashers

I have a DWI 612C Smeg dishwasher I have an error code of the 2 right hand LED's flashing Have tried to reset the programmer (turn off, on then press program 4 times in 2 secs, wait 15 secs and turn off) This enables me to select a programme, but when the programme starts, after five mins it beeps and carries on making the draining pump noise and the programme never starts When I turn it off and back on I get the far 2 red lights flashing again Have looked for signs of blockages and can


... Smeg 24 in. DWI612 Built-in Dishwasher

2006 kenmore elite dishwasher 665-17263402- the clean light flashes 7 times , pauses then flashes again 7 times. What does that code mean? Cannot get washer to operate.


The blinking "clean light" is a common problem with some of the Kenmore and Whirlpool models dishwashers. The problem is usually attributed to water supply temperatures being too low when filling. Apparently, there are some issues with th ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Haier dishwasher CDW300SS beeping 10 times and 4 lights flashing,,, help The dishwasher will work, it fills, it washes and it empties, BUT will not start now, and the 10 beeps and the four lights flashing,, so wont restart and go throught the program... Is there some way of resetting the dishwasher to restart. help thanks. glenn


... Haier Dishwashers

My deceased parents have a GE dishwasher (don't know the model number - can't find it on the machine and can't find the paper work) that stops working shortly you start it and displays a message on the front panel that says "Blocked wash arm - check for wash arm obstruction - restart". We restart it and get the same message shorty thereafter. This happens when the washer is COMPLETELY EMPTY, even when we remove the bottom rack. It first started after several month of inactivity. We'll just t


Could be false sensor input, could be that the arm is not turning, I am not sure how old your machine is, but age could play a part if the arm is "in fact", not turning. If you are not mechanically inclined, I would suggest that a qualified repairma ... Dishwashers

Hi, we have a Hoover HEDS668-80 dishwasher at work. The first problem we had was none of the programs would run this turned out to be a broken door lock. After replacement we managed to get one pre wash and one wash program to run, now when we try it, it starts but after 2 minutes the pre-wash and wash lights flash and the machine beeps 8 times. Can anyone help?


... LG LDF6810 Built-in Dishwasher

My dishwasher seems to be locked up and needs to be reset. the clean led is constantly flashing. i had this trouble in the past, and the serviceman reset the dishwasher by using the touchpad on the front as a code and washer worked again. do you know the code.


Control is programmed to\015\012stop the current cycle and\015\012not allow any further\015\012cycles if it suspects a\015\012faulty heater (no\015\012temperature increase\015\012detected in heated\015\012int ... Whirlpool 24 in. GU3200XTP Built-in Dishwasher

I have an Electrolux EIDW 6105GB1. The washer fills with water then immediatly drains back out, the lights all flash and the trouble code light under the kick panel indicates the wash pump. It has done this before and I took the pump out and checked it with power direct, then returned it to the main control board plug and it was working and pulsing it's speed as it should. It worked fine for several weeks and now it's doing it again. Is it possible that there's a problem with the water float ins


Hi\015\012\015\012The issue is either with the wash pump that is going bad or\015\012the motor itself that is unable to run. As the washer fills and then drains\015\012immediately so the pressure/float switch should also be checked. Hope ... Electrolux EIDW6105GW 24 in. Built-in Dishwasher

FDW80 the error code DEMO is on permanently and won't let any program run. the refill salt and rinse aid are flashing but they have been filled already. I have tried holding the on/off button and reset button down together but its not working, and i've tried switching it off at the plug and leaving it for a while, but nothing.


When the support engineer says press the 'on/off' button and 'start/reset' down together, press very hard. Press hard for 5-6 seconds and a the wording 'demo off' appears for a split second, then resets its self ready for use. ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

DELONGHI DISHWASHER HI, we just purchased a Delonghi dishwasher DW67S/W and it reads Error code 4 which says that the inlet has been overfilled. How do we drain it or get it working? It wont allow us to do anything more. The store we purchased it from is closed so i cant ask them. Thanks for your help. Chocy


... Dishwashers

I have a Troy built 2550 pressure washer. I bought a turbo tip and cant seem to get it to work correctly. What should i do??


... Briggs & Stratton Pressure Washer Quick - Connect Turbo Nozzle

I have bought a fisher and paykel model DW60CSX1 second hand... i have connected all the relevant pipes and taps, the washer gets to a point in the cycle where it stops and thw 1st, 2nd and 4th lights flash and beep.. i cant find a users manual anywhere...


My manual says that this means the drain hose is crimped or bent, or the drain hose is too high. In other words, the drain can't drain for some reason. ... Fisher Dishwashers

Have a lg model lds 5811st model dish washer for a little over 2 years and had the le error button .called technican replaced the motor now 4 weeks later the same error button.and the cancel button wont release the water standing in the bottom.also cant get repair man to garanty his work or parts.


Take off the door cover and you will find the wires melted into a black blown in insulation. Carefully free the wires and run a quick check to see if any of the wires are broken. If they are cut them and splice them back together. It takes a while ... LG LDF6810 Built-in Dishwasher

I have a Troy built 2550 pressure washer. I bought a turbo tip and cant seem to get it to work correctly. What should i do??


... Briggs & Stratton Pressure Washer Quick - Connect Turbo Nozzle
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1448 seconds