Having problems with your Dishwashers ?

We have a hotpoint DWF30P/17 Dishwasher which no longer heats or washes with hot water. The cycle completes the wash but no hot water. Can you advise? thermostat element controller


Answers :

Before I went with the controller, I would probably try the heating element itself, they are usually not that hard to replace and may be cheaper. I know its not that much advice, but just trying to help.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a hotpoint DWF30P/17 Dishwasher which no longer heats or washes with hot water. The cycle completes the wash but no hot water. Can you advise? thermostat element controller


Before I went with the controller, I would probably try the heating element itself, they are usually not that hard to replace and may be cheaper. I know its not that much advice, but just trying to help. ... Dishwashers

FDW60 Fault Hi, I have exactly the same problem. My dishwasher starts and washes ok but appears to get very hot during the drying phase and then the two lights fast and eco flash warning of a heater problem. I suspect either the heater, thermostat or control PCB. As the rest of the cycle seems of and the water gets hot then I'm assuming the heater and thermostat are OK. When the dishwasher attempts to dry is when the problem starts. Did anyone find out what there fault was? Thanks


Hold down the start key and you will re- set the D/W. Please Rate This !!! Thank YOU !!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Yes I have a whirlpool DU1345XTVB1 dishwasher. Just got in July. After each wash cycle the dishes are not dry. I have been using Finish gelpacs w/jetdry & also have a off brand drying agent in reservior to help dry dishes. The water temperature is set pretty hot & washer is draining good. I have tried checking wash cycle a few minutes into 1st cycle to see if water is in filling & heating. Didn't know if maybe heating element going out or thermostat not working? Thank you for your time.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Dishwasher issues dishwasher runs but water does not get hot and wash cycle continues endlessly until stopped or rest. Do I have a water heating element issue or a controlling PCB issue?


You should always turn the hot water faucet at the kitchen sink first before starting dishwasher. If you don't your entire wash is cold water. This will also cause the water temp mode to take forever to heat the water to the 140 that is factory set. ... Dishwashers

HDW101SS does not heat water. Heater element mearures 28 Ohms. Temp Limiter is N.C. Temp controllers TS50 & TS60 not found. On economy wash timer moves as normal then stops when red heater light should come on. If the timer is assisted one click it will progress as normal but no hot water.


Hi.If the temp limiter shows no continuity, there will be no voltage reaching the element contacts. The high limit is connected in series with the heating element. If the hi limit is open the element will not get power. Any technician wil ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

Kenmore Elite Stainless Steel 24 inch tall Model 66577963K701. The heating element works for "heated dry" but not for "Hi Temperature" wash. It used to do so and when I opened the door a nice blast of steam would come out. My hot water tank is a great distance from the washer so we usually run the hot water tap in the sink for a bit until hot water comes... but the heating coil no longer kicks in on any of the cycles (Smart Wash / Normal Wash ). The high limit switch works and as I said, th


... Kenmore Dishwashers

I have a Fisher & Paykel 913T soft touch dishwasher. On all types of washes when the wash cycle starts there is no 230 volts on the element & after 5 minutes the wash cycle finishes & then goes onto to the next cycle. None of the wash or rinse cycles heat the water but on the dry cycle their is 230 volts onto the element & dries the dishes OK. Is my problem the power supply PCB or could it be the Controller PCB? Does the 230 volts to the element on dry cycle come from the same cicuit on the po


Have you considered the possibility the water temperature sensor may be faulty.\015\012\015\012If the controller is getting false water temp reading then it may never turn the heater on.\015\012\015\012Generally with FP dishwa ... Dishwashers

Smeg Dishwasher DWD 63.1 SS, not heating; I have Smeg dishwasher that is sticking in its cycle (wash phase), water was cold, so I assumed the element had failed (or tank termostat), so I have replaced both element and tank thermostat in turn. No change, water still cold and dishwasher sticks in the wash cycle. Any ideas? (Note, no diagnostic leds on this model)


... Dishwashers

I have an Indesit IDL500 dishwasher. It had stopped heating the water up, it looked as if it had short circuited and so i replaced it, i have power going to the element. A couple of forums state that it may be the pcb behind the timer/selector switch. Does this pcb control the program selection and heating of the element? or is there a thermostat that controls the stop and start of the heating element? Any help would be greatly appreciated


Hi\015\012\015\012The unit\015\012has two thermostats and you can test both of them for continuity before\015\012replacing, no continuity replace the thermostat. Hope\015\012this helps...please post back fo ... Indesit 24 in. IDL500 Built-In Dishwasher

My kitchenaid dishwasher will not complete a washing cycle. the water heating seems to be staying on all the time. could my heating element be shot. the water seems hot when i open the dish washer during the cycle but it is connected to the hot water supply line. thanks


... KitchenAid Dishwashers

Even though I turned up the thermostat on my hot water heater, the water in the dishwasher does not seem to be hot enough. Mold is growing in the food grinder and even though I choose the heat dry option, the dishes are never dry. Yet, when I touched the element, I got burned. The dishes are not getting clean because it doesn't seem to be hot enough to cut the grease.


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

501ht goes thru wash cycle but cam stops just before rinse cycle clicks in - stays in wash cycle - turned thermostat to booster down in temp -cam then keeps going properly but with no hot water from booster - replaced thermosat still same result - apparently a safety ? no booster water no rinse?


Did you get a solution for this? I am having the same issue. Please email me at [email protected] Thanks -Eric ... Moyer Diebel 24 in. 501HT Built-in Dishwasher

I have a Beko DE3542FS dishwasher which has stopped heating the water. I know the heater element is ok because I have had it tested. I was wondering if the thermostat was faulty if this would account for it not heating. The element has had 240v applied and becomes hot. So my reasoning is that it is either the thermostat or the programmer. Any suggestions?


... Dishwashers

I have a JDB1090AWS about 3 years old. We noticed a smell and found cutting boards and plastic cups melted. Machine was off. Had to turn off the breaker. Checked both leads to element & have power even with machine off. Not sure if it could be the limiting thermostat; I assume that is to shut the heat down when it gets too hot. Element is on though when it shouldn't be to begin with. I did have to tighten the water supply. Had some water underneath, but all wires seemed dry. Any tests I should t


The heat element can only get so hot.It's timed so it doesn't exceed a period of on, exposing dishwasher contents to continuous high temps.Watch the timer and take note how long it broils your cookware.Good luck. ... Dishwashers

Whirlpool dishwasher ADG 7460 will fill with water ok and wash but will stop before it finishes the cycle leaving water in the machine. if you set it to rinse it will drain the water .... so the drain pump is working ..... water it drains is hot so the element seem ok ..... help


Hello & Welcome to FixYa Dishwasher not draining completely problem usually ... Dishwashers

My whirlpool quiet partner II is not quiet at all. When I start the cycle it starts humming and a little vibrating and I open it up and no water. I close it and wait it out every 10 minutes I open it back up and no water. The heating element is hot and stinky since there's no water. But once the wash cycle is over the rinse cycle works and theres water. What's the issue?


... Whirlpool GU2400XTP Built-in Dishwasher

GE Dishwasher SSD3900J00ww wash water cool heating element hot on


Crew that installed new cabinets and sink hooked dishwasher to cold water line I switch it works fine now. Thanks Don ... GE Dishwashers

AEG OKO Favorit 4020 no water flowing into spreaders to wash. Water flows out the side outlet and the element heats up but no water?


... Dishwashers

ARISTON LSI 45/50 UK ALL COLD CYCLES ARE PERFECT ON HOT CYCLES IT GOES THROUGH ALL THE STAGES BUT NEVER ENDS THE CYCLES AND ALSO I THINK THE ELEMENT TEMPERATURE IS NOT BEING SENSED TO ALLOW HOT WASHES TO CONTINUE AND FINISH I ALREADY REPAIRED THE INITIAL FAULT WHICH WAS A RED 2 PIN CONNECTOR WITH A WHITE SOCKET GOING IN TO IT BOTH WITH 2 RED WIRES ON WHICH WAS VERY BADLY BURNED / CORRODED I REPLACED THIS WITH A 15 AMP CONNECTOR BLOCK BUT NOW I HAVE THE HOT WATER CYCLE FAULT


I tried to look up your model dishwasher ( aristion lsi 24/50uk ) by whirplool / can not find in data base / also you stated that all cold cycles work/ most d/w only use hot and there is no cold cycles . so there is always time to ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Hello Dishwasher Whirlpool DWF A00 - the light is flashing indicating a fault. The interior appears to be too hot and the machine was making a noise similar to an element in a kettle with insuffient water. (Although there was WAS water in for the wash) Thanks for any help!


There is a recall for such a problem you need to call whirlpool. ... Whirlpool GU2400XTP Built-in Dishwasher

DWF614SS not heating water, flow through heating element has been replaced and tested but still no hot water. Do I need to check the thermostat, if so, where is this located? Thanks for any help with this one. Owen.


... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher

I have a 2 year old Electrolux ESL 63010 dishwasher, and it worked perfect until a few days ago, when it did not wash cleanly and the dishes came out cold. I read a few forums and it seemed to indicate the heating element. So I ordered one a fitted it, but still the water is not getting hot, or drying the dishes after the complete cycle. I have done a visual check of the PCB board, which looks clean and good. No error sounds, and it completes all programs, but with cold water and no drying. W


... Electrolux Dishwashers

Hi I have a Zanussi Di 720 there is water going in but can you tell me if the water should be covering the element when it starts the wash cycle it drains ok and I have looked at the hose and there is no kinks in the hose can you advise please


... Dishwashers

Conia CDW0305W dishwasher. Gets stuck on the cycle and has be clicked along to finish. Doesn't appear to be heating as it first sticks at a point I'd expect hot water wash and dishes come out with grease residue and still wet. I live in the middle of nowhere, to a professional will cost me a fortune. Is this the metal element and can I fix it myself? Please help, I'm sick of hand washing!!


... Dishwashers

Dishwasher IDL530 machine runs ok .Water did not get hot .Renewed element but water did not hot.Could it be the thermostat ?


Yes or timer ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1832 seconds