Having problems with your Dishwashers ?

I have a KDW 243 A dishwsher. It was opened before the end of the cycle, and I cannot re-set it. Befor ethis, it was working fine. Whatever I do, the drain pump runs as soon as the power button is pressed, and the programme button does not operate.


Answers :

Hi
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks for using FixYa. This\015\012issue can be either due to a faulty door latch or door lock switch which is not\015\012engaging itself. And, if the door latch will not engage the dishwasher will\015\012sense it as open door and will not start the cycle. And the sound might be\015\012coming from the door lock solenoid (a hum/buzz sound).
\015\012\015\012
\015\012\015\012The light\015\012also blinks when the dishwasher detects a no-fill\015\012condition. You’ll need to get access to the fill valve by removing left\015\012panel, look at back to see where valve is when you get to it remove one of the\015\012wires and set meter to ohms setting and put a lead on each tag on valve. The\015\012reading you should be about 3.6k ohm if you don’t get a reading then the valve\015\012is at fault.
\015\012\015\012
\015\012\015\012I'll also suggest you to check\015\012the detergent dispenser solenoid for this issue. Remove the door\015\012panel and see if there is a round item at the dispenser assembly with two wires\015\012attached to it. Put the dishwasher into a cycle and when the noise appears,\015\012gently press on the solenoid to see if that is where the noise is coming\015\012from.
\015\012\015\012
\015\012\015\012Please do accept the solution if\015\012the issue is resolved or else revert for further assistance.
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks
\015\012\015\012
\015\012\015\012Rylee
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a KDW 243 A dishwsher. It was opened before the end of the cycle, and I cannot re-set it. Befor ethis, it was working fine. Whatever I do, the drain pump runs as soon as the power button is pressed, and the programme button does not operate.


Hi\015\012\015\012\015\012\015\012\015\012\015\012Thanks for using FixYa. This\015\012issue can be either due to a faulty door latch or door lock switch which is not\015\012engaging itself. And, if the door latch will not engage the ... Dishwashers

Bosch SHX46A02UC-21 Won't Fill and Drain Runs Continually. Original presentation of problem was that it wouldn't drain. Discovered that Garbage Disposal had plugged drain line. After clearing Drain Line, now drains fine but the drain pump runs continuously and it never fills with water. Have done the Cancel, Power Off routine however, even after that, drain pump runs continually.


Float switch is in the flood position and the drain pump is running..\015\012there is water under the dishwasher or that switch is stuck up.. ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Jenn-Air JDB9910AWB dishwasher. The problem I am having is everything seems to work fine until the drain cycle. It sounds like the pump is frozen. After selecting the drain button you can hear a click in the control panel followed by a 1-2 second growl in the pump but it doesn't turn or pump. I am assuming the pump runs in reverse for draining? Is it safe to assume the pump is bad?


... Jenn-Air JDB9910 Dishwasher

Bosch dishwasher model shx36l fails to stop pumping. The drain was clogged. I cleared the drain. Dishasher backed up, water overflowed. Clog has been fixed. Dishwasher will not stop trying to pump water out. There is NO water inside dishwasher. I wish to run another load however unit fails to respond. Pump is operating even when front door to doshwasher is open. Turning the power button to OFF is the only remedy to stop drain pump from operating. How to fix?


... Bosch Integra® 500 SHX46A0 Dishwasher

My brandt VF300 doesn't drain at the end of wash cycles. If you run the soak programme it drains fine. Some time ago the door was adjusted by an engineer, when he arrived he pressed some buttons which then drained the unit immediately, I have forgotten which buttons! Is there anything I can do to reset the thing, given it drains on soak I am doubtful the drain pump has broken ir is blocked?


... Dishwashers

I have a GE monogram zbd5900 that continues to drain, won't shut off. The drain pump just runs. None of the lights on the control panel will come on, tried pressing and holding buttons to clear, nothing. Turned off and on circuit breaker (even left it off overnight) and did not change. Drain is not blocked, pulled the unit out and put water in the bottom and it pumped the water out just fine. any thoughts?


See if you can access the tech sheet, should be on the right side of the underside of the unit after you remove the toe panel, or perhaps in the console. Almost sounds like a stuck key pad but the tech sheet might shed more information on this malf ... Dishwashers

I have a Whirlpool GU2275XTVY0 when I start the cycle on normal it will run for about 5 minutes then the power button starts flashing and wont run. It drains fine and starts fine just wont finish the cycle.


It might help if the wash arm had started moving when it shut off.\015\012\015\012Unless it is always exactly 5 minutes I would say perhaps the door switch is out of alignment. It might start ok when you engaged at time of closing door bu ... Whirlpool Gold GU2275XTV Builtin Dishwasher

Our Bosch dishwasher #SHU9922UC (FD8007) will not turn on properly. Only its drain pump starts -- and keeps running -- when it's powered on and the door's closed. Pressing the two "drain cancel" buttons for more than 3 seconds doesn't help. Neither does cutting off power, then turning it back on in the hopes of resetting the machine's 'computer'. No water inflow occurs. Help?


I had a similar issue after I replaced a bad drain pump, seems the logic got hung up.. I poured in a pitcher of water, closed the door, it drained and was then ok - worth a try. If not, you may have a bad water level switch. ... Dishwashers

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

ASKO dishwasher D3122 drain pump wont stop pumping and the machine wont respond when we press any of the program or start/stop buttons. the program light is flashing. We can turn the power off with the main switch on top of the door but when turning it back on the pump starts pumping again. please tell me how to fix this problem so we can get it up and running again.


... Asko D3122XLSS Stainless Steel Dishwasher

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an


... Asko Dishwashers

Ok Guys, I have a BECO DSFN 1530 W Dish Washer. The drain pump is constantly running. It drains out fine - i've filled it up with clean water to check. The 'hold button in for 3 seconds to can


... Beko 24 in. D3731F Free-standing Dishwasher

Drain pump runs non-stop. Continues when dial is in Stop position. When disconnected for hours, drain pump starts immediately when power restored. In any wash cycle position, drain pump runs and cycle never commences. Small amount of residual water in drain line when impeller cover removed. Board? Switch?


Sounds like the flood switch has activated.\015\012\015\012You will have to drag the dishwasher out from under the counter after turning off the power to it. Tilt to one side so that any water collected under it is expelled. This will fre ... Miele 23 in. Novotronic G841 Built-In Dishwasher

We have ASKO 1805 dish washer. As soon as turn on the power all lights are start flashing and there is no response whatever button is pushed. All the lights simply keep flashing. There is no water being pumped into the machine.


Child lock may be activated ... Asko Dishwashers

Kenmore elite 1393 worked fine for a week or two then began to stop in mid cycle,we could drain the water and try again but would shut off almost immediately. sometimes trying to restart it there would be NO power to any buttons, after waiting for awhile the buttons/lights would work again but the washer would not run a full cycle.blue light would light then go out within a minute or so.


... Dishwashers

Kenmore dishwasher wont drain , but pump runs fine


... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

Dishwasher LFK-011S: First it occasionally gave four beeps (overflow) but no water in bottom or under. I then noticed that with lower water pressure machine worked ok few months. Now last week in the middle of program, drain pump started to run, machine gave four beeps and pump kept running even main switch off. Now when I plug in power cord, the pump starts to run immediatelly


... Fagor LFA013 SS 23 in Builtin Dishwasher

Kitchen Aid Dishwasher KUDR24SEBLO does not drain 100%. I have removed the drain hose and chcked the sink P-Trap, [it drains thru the garbage disposer]. Unit is 10 years old, otherwise works fine. I am having difficulty removing the impeller and items above the pump to see if it is clogged. Do you think I have a partially clogged pump or a timer issue that prevents the pump from completely emptying the bottom of the dishwasher? We have run the dishwasher 20-30 times since observing the problem.


Hi there,\012Please check out the following -Pump - Your dishwasher pump ejects the water. The pump is usually mounted directly to the motor, then attached to the bottom of the dishwasher. You can reach the pu ... KitchenAid Dishwashers

Electrolux esl 6115 integrated dishwasher.Water not being pumped/ draining away. Have tried laying drain hose flat on the floor water drains away fine and water runs clear but with hose connected cycle does not complete and water remains in bottom of dishwasher. Is there a drain pump in this model


... Dishwashers

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

The dishwasher pump sounds like it is trying to drain, even when the stop button is pressed and the door is opened. The only thing that stops it is turning the power off at the power point. However, when the power is turned on the pump continues. The wash cycle icon flashes, but the usual cycle indicator is not lit at all. The dishwasher will not commence a new cycle.


... Asko D3122XLW / D3122XLB Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have been interacting with Daniel about my Dishwasher Smart Dispenser problem. The last thing he had to say to me was that I needed to replace my drain pump. Before doing this, I would like an explanation of why a new drain pump will solve my problem since my dishwasher is draining just fine...it is my Smart DIspenser that is clogged up and not working ?? See the discussion here: Dear go4t9ers, There is a new Comment for the I would like to run the Smart Dispenser Purge Solution on


Ok first this is the schematic for your entire machine http://www.s ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1847 seconds