Having problems with your Dishwashers ?

Water not drawing into machine Smeg EN50242

\015 I have cleaned all filters and checked inlet hose & filters. No warning lights. machine sounds normal but no water drawing into machine\015

Answers :

Check to see if the float switch located on the bottom corner of the dishwasher is not stuck in the up position. Move it up and down a few times and it should click each time you move it up and down.
\015\012If this is ok then you have to put a multi meter across the water inlet valve to see if you have a current flow the the valve. If you you have 120 volts at the inlet valve and still no water. Replace valve.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water not drawing into machine Smeg EN50242


Check to see if the float switch located on the bottom corner of the dishwasher is not stuck in the up position. Move it up and down a few times and it should click each time you move it up and down.\015\012If this is ok then you have to put a ... Dishwashers

No water I have the kenmore ultra wash quiet guard built in. You can hear the motor running but it is not drawing water into the machine. I have checked all of the hoses and connections and they are good....pump sounds like its running but just wont draw the water in.


Inlet solenoid not working, check wiring is attached ... Kenmore 24 in. 15932 Built-in Dishwasher

The water is not coming into the machine and the tablet is still dry even though it comes out the draw, the dishwasher makes a noise but no water s getting into the machine


Check your water inlet hose and any filters attached to it. Some hoses have a little turnkey tab to turn them off. Make sure this has not accidently gone into the shut off position. If you pull out the machine you will hear if the water is coming in ... Dishwashers

Hi :) We have a Bosch slimline dishwasher type SRS56A02 GB/08 - it doesn't draw in water - the timer counts down but nothing happens. We checked these pages and cleaned the filters on the inlet water line but no change :( I saw that it might be the inlet water valve - is this easy to get to - do we need to take off panels? if so, is there a manual available please? Over the past week or so it had got noiser - it was at its quietest while the water was draining out of the machine.


... Dishwashers

Smeg dishwasher model DI 612 C type 12053 good morning After selecting a program and shutting the door the drain pump starts and runs for 2 seconds then stops. The machine makes a bleep noise then the drain pump starts again running for 2 seconds then stops again and the cutting in and out process continues and the machine never reaches its selcted cycle. No alarm lights are displayed. I have filled the machine with water so that the filter is submerged and the level is


... Smeg Dishwashers

Dishwasher model en50242 after cleaning both filters and turning on the valve etc no water is going into machine. The control panel shows 2 lights one above the tap sign the other above the programe light. The pump runs for a few seconds then stops and nothing further happens. We are in a high water calcium area.


... Siemens Dishwashers

I want to disconnect the water supply. I am replacing this 12 year old slimline smeg dishwasher and they are coming to take it away to morrow. The connection to the water supply is via a grey plastic box with and electrical sign on it ( a lightning flash with an arrow on the end). Although I have disconnected the eletricity supply (unplugged the cable to the machine) I am concerned about what this bos may be. Can I just unplug it?


Hello Henry,\015\012\015\012It's the aqua-stop safety valve and yes, you can just unplug it. Make sure you close the valve on the water-supply first or it's going to get rather messy!\015\012\015\012FYI, the aqua-stop is a sec ... Dishwashers

Dishwashing SMEG SDCY 66 (made in Italy) As soon as machine is starts (from program 4) water supply valve open and water running in about let say 5 minutes no any further functioning and some strange nice from below looks like something is running dry. What can be the case?


... Smeg Dishwashers

My Candy DFI85S is not drawing water into the machine. After a short time of trying, the machine stops and sounds three beeps. The tap is definately turned on. Any help or advice would be appreciated.


... Dishwashers

SMEG dishwasher... L5 eco A few years old... been working perfectly... water not draining properly - water left lying in bottom of machine after cycle finished.


... Smeg Dishwashers

SMEG STX dishwasher does not complete the wash cycle, stopping after 3 minutes on all cycles displaying error code E1. The machine seems to start with the usual whirring noise but then stops after 3 minutes without pumping in water. The machine is a few years old now but has needed 2 new control panels already although this does not appear to be the problem this time. Any suggestions? Thanks DW


... Dishwashers

We have a +11 year old Bosch SHU3006/UC/U06 that never leaves the wash cycle. We had to stop it during our last test run at 3 hours. Chat advise is suggesting a water temperature problem (I origionall thought the timer), suggesting that the cycle will not advance until it hits a set temperature (170 degrees). We checked and noticed that the water in the machine was only around 90 degrees during a wash cycle. We do not have exploded views or parts drawings, nor electrical schematics. I wou


Check continuity of the heating element to see if it is broken/open.\015\012\015\012The dishwasher prefers that the incoming water (water heater) be 120 degrees (F) ... Bosch SHU3036UC Dishwasher

I have a Smeg Di612c dishwasher. The machine lets in the cold water but then stops without taking the tablet. I have checked the error codes in the manual (E2) and tried the reset options but the problem persists.


... Smeg Dishwashers

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

I have a Neff built in dishwasher - I think it is the S4443N6. I've tried all the cycles- quick wash/intensive/eco/etc but none seem to wash although the machine appears to go through the motions. The powder draw does not empty properly and the powder is hard after the cycle finishes. Water does not seem to be coming through with enougn pressure although I have checked for blockages in the pipes and cleaned filters.


... Neff 24 in. S4443N6 Built-in Dishwasher

I have a Kenmore dishwasher Mod. #665 17729000. When I opened it there was a plastic tube laying on toip of the contents of the bottom basket: it looks like it could be the feed tube of water to the top basket, but I could find no way of reattaching it. I have not been able to find a detailed drawing of the machine on line. Help please.


W have herebelow the link of your model with all parts layout which we believe will helpyou see how everything is put together and also you can order any part thatmight need to be replaced. Don't thing we need to describe a ... Kenmore Dishwashers

Smeg df612 dishwasher problem, lights up as a e2 fault ,i have tried draining the dishwasher but still the same problem . the salt container is full of water is this normal?. and how do i reset the machine . ive tried pressing the programme button 4 times but it just shifts through the different cycles . can you help please/.


... Smeg Dishwashers

A feew weeks ago Smeg STA6047 dishwasher stopped in the beginning of the programme after approx. ten minutes, and gave the error code E9. There had been clearly water in the machine, but maybe not enough and the detergent box was not open. However, when technician came by two weeks after, the dishwasher worked and he said it was in order. But only after being used only once, the same problem reappeared. First the washer gave the error code E8, on the second try E9. And now it does not start at a


As you know E9 is linked to the water inlet problem. \015\012\015\012There are two scenarios here - 1) Are you using the Aqua-Stop safety system? If this is trigerring then it can shut the inlet water. The reason it can trigger is if the ... Smeg Dishwashers

SMEG STX45 built in dishwasher. E1 message do not have the user manual. It is trying but does not seem to be able to draw in water? more recently its been checked by a technician as it was tripping the fuse box, technician circuit tested and said it was fine?


... Smeg 18 in. STX45-1 Stainless Steel Built-in Dishwasher

My Smeg dishwasher model DW1 410 is not drawing the water any more.


More than likely water inlet valve is bad. Maybe replaceable. ... Smeg CSU2001 Built-in Dishwasher

Maytag Model No WU202 is running through all cycles but is not pumping out the water from the tub. I can hear the pump running and a gurgling sound. Could it be the micro mesh filter that is plugged? Any detailed drawings available of the lower wash assembly and instructions to take it appart? This machine is more than twenty years old.


Hi,It sounds like your belt broke. Open the bottom access panel below your door and check. The part is :-http://www.repairclinic.com/SSPartDetail.aspx?PartID=2814&PPStack=1If you take off the front ... Maytag Dishwashers

I have a Smeg dishwasher SA660 EB. Still like new . Hardley used but have problems with the timer switch not progressing past 5 and also had the thermostat replaced as a loud bang heard and the machine did not work. Since warranty on repair run out it sounds like water is leaking around the thermostat through onto electrics as loud bang noise heard again . I found the thermostat just pushes up into the rubber seal in the bottom of the dishwasher. I have taken out the rubber seal as this also loo


... Smeg Dishwashers

My smeg dishwasher has a e2 problem . how do i empty all the water in base unit to reset the machine ? . my dishwasher is a intergrated one


... Smeg DF612SI Dishwasher

Smeg Allegra NZL750 drains water after wash but then it fills up bottom with water


... Smeg CSU2001 Built-in Dishwasher

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1427 seconds