Having problems with your Dishwashers ?

Very noisey, dial will not move round, seems a if its stuck, even when you move dial manually its just the same noise continuous


Answers :

Timer is froze up!! need to change it out to fix it
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Very noisey, dial will not move round, seems a if its stuck, even when you move dial manually its just the same noise continuous


Timer is froze up!! need to change it out to fix it ... Dishwashers

I have an avanti dw 18 dishwasher . the problem i am having is the when i turn the on button on the motor goes on however no water fills up. The motor is only humming. But; when i press down the float from inside the machine the water fills up and the machine starts to work. after the water drains again the motor continues to run and hum and the dial does not move. when i manually move the dial nothing seems to change . the motor continues to only hum. Even when the dial is in the stop position


... Avanti Dishwashers

I have just moved into a home with the DS-603i and used it for the first time. I put it on the first load and seemed to go for way to long. so i opened it up and t washed the first load ok, but continued to make noises. It would make these noises even when draw opened. Turn on & off at power and it doesn't change the noises. The light on inside indicates rince, which i think is a F1 error code according to the manual online. Any tips on how to fix this?


The F1 error code indicated a leak problem. The noise that you hear is from the pump motor. There is a leak due to the top lid not sealed properly, so the water is shooting out during the wash cycle. It did not seal tightly because there are 2 actuat ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

I stupidly put washing up liquid in my very old Bosch SPS 21/24 as i had run out of dishwasher tablets - a few bubbles leaked out but all seemd fine and now it makes all the right noises but nothing actually happens even if i manually turn the dial to move it on to the next stage- any hope??


Take a shop vac and remove all the water and suds.\015\012No shop vac...use a towel or sponge.\015\012Then use a pot to manually fill the dishwasher with cold water. Set it to wash a few seconds then go to pump out setting.\015\012R ... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

The timer dial on the dishwasher moves to about the 6 o'clock point and does not move from there. There is clicking noise, and I can nudge the dial and it will move. I removed the t-stat (there was a white substance between it and the door - what is that?), but don't know how to check it. Am I checking for continuity? Thanks much, Roger


... Bosch 24 in. SHU30 Built-in Dishwasher

I have an old (not sure what year, 80s?) Kitchen Aid energy saver V Custom by Hobart dishwasher. We opened the dishwasher in the middle of a cycle and now cannot get it to re-start. When we lock it back up and push our normal buttons (Low Energy and Energy Saver/Dry Heat Off) or any other combination of buttons, the dial does not turn automatically and the cycle does not continue. I have also tried advancing the dial manually and still, nothing happens. I have even tried advancing it all the


... KitchenAid Dishwashers

My d1716 continues to run, but does not move forward in the cycle. I can even open the door and it continues running. If I didn't unplug it, the motor would likely burn out. Do I need a new dial? Thanks.


Hi\015\012\015\012I would suggest that your flood switch has been activated. There is a float on the bottom plate or base plate of the machine. If there is a water leak, the float rises and triggers the flood switch.\015\012\0 ... Asko D1716 Built-in Dishwasher

Machine cannot finish cycle and is stuck in pumping out mode. Only tiny amount of water in drain basin at bottom, no excessive water. Was set at 10pm, still attempting to drain 8am! Has no diagnostic dials or manual over rides so continues on whether door is open or closed, even if I switch off and on again. Possible related issue, recently finish at end of washes has been "grainy", far from perfect, surfaces slightly sandy feeling.


... Bosch 24 in. SGV43A03 Built-In Dishwasher

My dishwasher was working fine til this a.m. Making a loud buzzing noice when clicking into a different cycle. Had to manually nudge the dial to move it to the next cycle to stop the loud noise. This happened several times during the washing cycle.


... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!!


The Timer might not be bad. If one of the two thermostats is bad, the Dishwasher will exibit the same symptom. The thermostats are 141 deg. F and 161 deg F.They only cost $20 each. The Control Module is close to $200. ... Bosch SHU4006 Dishwasher

Hotpoint Model HDA 3500N 10 BB Unit is only about a year old. The dial does not move. I noticed it when the washer was on for more than 3 hours and saw that the dial was still in the middle of the wash cycle. I then turned it to the rince cycle which operated there (not moving) until I manually moved it to dry. Did not move from there either. Thank you for any help you can give me.


HiThanks for using FixYa. From what you have described it seems to be an issue with the timer that has gone bad, they don’t often fail but if everything else is working fine then it is the Timer ... Hotpoint Dishwashers

I just moved into a house that has a Maytag Quiet 300 dishwasher. After about 2 weeks, I'm hearing a VERY loud, almost grinding noise about 6-7 minutes into the wash cycle, then again near the end of the wash cycle. It sounds like a motor thing and I'm hoping to avoid a repair bill right now, the cost of the move wiped us out. Is this something that I can fix, and if not, will continuing to run the dishwasher with the noise kill it?


You can continue to run it. it may correct or else it will get worse.......then u can get back and i will help u decide what to do ... Dishwashers

Problem with ASKO 1385 dishwasher. Unit has manual cycle knob, not electronic. Clock/timer seems to work normally but no water is pumped in and a motor runs continually throughout cycle, even during drying time. Motor continues to run continuously after end of cycle.


CHECK THAT THE WATER IS ON TO THE UNIT, AND IF VOLTAGE IS AT WATER INLET VALVE. IF VOLTAGE THEN WATER SHOULD BE COMING IN EITHER BAD INLET VALVE OF CLOGGED SCREEN IF THERE IS VOLTAGE TO VALVE. NO VOLTAGE THEN CONNECTIONS OR TIMER WOULD BE NEXT. ... Asko 1385 Dishwasher

Kenmore elite dishwasher runs until it is manually shut off by opening the door? My Kenmore Elite runs continuously until I manually drain (cancel) the cycle. Then I have to rewash with no soap to simulate the rinse and again manually drain (cancel) the cycle. This was a $650 dishwasher. I am not sure how to reset the controller or even trouble shoot for an error code. Any suggestions?


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Dishwasher was on and had a power cut for no more than 5 mins. since then dishwasher dial will not move round on its cycle so ends up being on forever if not manually turn dial


... Hoover 24 in. HD98E Built-in Dishwasher

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

ASKO ASEA 1652 dial sticks in the cycle between "Light" and "Two Rinses" and needs to be manually nudged forward along its cycle. After a slight nudge, the dial moves on its own to "Dry".


... Asko Dishwashers

I have a Bosch Dishwasher, Model SHE46C06UC. No mater what cycle I start it in, it simply activates the drain and continues to run without ever starting. Within the last week prior to the dishwasher not working, I noticed a low hum/vibration emitting from the dishwasher. I've clean out the screen and drain filter, removed the pump cover to check for any debris. I've manually added water and it does drain. Additionally, the drain cycle continues to operate even with the door open.


First thing you may want to check is the door switch. You can pull it off and measure the resistance with an ohmmeter. If you get good reading while pushed in and none while switch button is released, then it is a good start. Next, you may want ... Dishwashers

Elba dishwasher (turn dial model) under 2 years old, this will be the 3rd time this has occured. You turn dial to preferred setting and press power it pumps out continuely and wont move to next stage, i have tryed reseting but to no avail please help, I will not be buying another F&P product again.


Your unit has had a "brain aneurysm" IE: Your Microprocessor has failed...Either a fix or a new one? ... Dishwashers

Bosch logixx dishwasher sounds like its running continuously & will go through entire program but does not fill or wash. Filled it with hot water manually to try for air locks & it does drain out. Then continues to attempt to drain even while door is opened. My amateur guess is that its a float switch but can I get at it from the inside or from the back? If thats what it is. Hope you can help,thanks.John


... Bosch 24 in. SGS09L12 Logixx Free-standing Dishwasher

The dishwasher does not complete a cycle. It starts the cycle just fine but then it stops after one minute. It seems like it gets stuck and won't move to the next step. I do hear a slight clicking noise similar to a clock ticking, like its trying to move on, but then it stops. It clicks three times. When I open the door the "fine china" light is on even though I set it on "normal". Is there a "re-set" button?


The Control Board is gone, the part is $475.00 Find a new one.... ... Viking Designer Series DFUD041 (Premium) Built-in Dishwasher

Dishwasher is reading "overfilling", but no water is in unit. Door can open, noise of motor or pump continues and will not shut off even with the Power switch. Only way to stop noise is to turn off the circuit breaker at the electrical panel. What does this sound like to you?


HI- The flood switch has been tripped. It is located under the unit and is not really accessible except by a Tech. The most likely cause it poor draining; if there is a little water left over from each part of the cycle then eventually the water ... Asko 24 in. D3530FI Built-in Dishwasher

Model #363.15161792 will not operate even after installing a new WD21X10013 timer. Timer moves, pump starts, but no water comes in to wash. The pump does continue to run. Now what?


... Kenmore Dishwashers

My Bosch integrated dishwasher(model SGV56A03 GB/12) runs through the cycle but doesn't stop at the end of the cycle. It continues to heat water and it sounds like the motor is running even though the time indicator shows 0 minutes. I have to manually switch it off. Any ideas before I call out an engineer. I have checked all the filters etc included in the troubleshooter info anf there are no blockages.


... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0709 seconds