Having problems with your Dishwashers ?

Got a Indesit Di620 Dishwasher that trips RCD after power up & immediateley as you shut door.Fault is definately related to pressure switch, disconnected pipe to switch and then able to start cycle, without tripping, small amount of water out of pipe,but cycle only lasts for a few minutes, then stops. ( blowing into pressure switch trips rcd )How can i test switch, or is it a water level problem ??Any help would be good, thanks S.C


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Got a Indesit Di620 Dishwasher that trips RCD after power up & immediateley as you shut door.Fault is definately related to pressure switch, disconnected pipe to switch and then able to start cycle, without tripping, small amount of water out of pipe,but cycle only lasts for a few minutes, then stops. ( blowing into pressure switch trips rcd )How can i test switch, or is it a water level problem ??Any help would be good, thanks S.C


... Dishwashers

We have a problem with our Miele G851 SC Plus dishwasher. We have not operated it for over three months as we were away on vacation and also because there were other issues in the kitchen due to some water flooding . Yesterday we switched on the machine and notice that the machine flashes the intake / drain light after a few minutes into the cycle and stops working. we have checked the drain pipe for blockages and also the water pressure is good. I disconnected the machine drain from the


Www.miele.ca/miele/canada/OperatingInstructions/.../G851%2005431311.pdf\015\012\015\012\015\012\015\012 ... Dishwashers

Over the past two years, the machine has occasionally stopped in mid cycle, while the pump continues to run, but the cycle stops advancing. Each time there has been water in the plastic pan under the pump, valves, and other mechanisms. The float switch has been tripped, stopping the cycle. Occasionally. but not always, the pump inlet has been partially obstructed by food waste. After bailing out the pan, the machine will run normally for weeks or months. There is no indication of a leak into th


Please post the exact make & model # so we can be more exact.\015\012THanks!! ... Dishwashers

Asko Dishwasher starts the cycle by pumping out as it should. But does not stop pumping nor advances. If I click it forward manually it starts to fill and then before overfilling goes into pump out without washing then just repeats this. Pressure switch tubes and air trap chambers are clean and no leak to trip spill switch. I'm guessing It is either the timer or faulty pressure switch any clues ???


If has "mother board" then water could have got in.\015\012\015\012Here Asko is low cost make so check cost before serviceman calls & charges & charges and so on. ... Asko D1706 Built-in Dishwasher

Hi. IKEA Whirlpool DWFA10 dishwasher.Firstly, when switching on the machine to befin the programme the machine does not pump residual water away.It then begins its cycle (in this case the pre-rinse cycle).After 12 or so minutes,when the cycle finishes and the water should be pumped away,the machine stops and the green warning light keeps flashing 4 times intermitantly.


... Dishwashers

The top drawer of my fisher paykel dishwasher stops during the cycle and shows an icon of a tap with a line threw it (assume that means no or low water pressure). the bottom works fine so I assume water pressure is not the issue; is there a sensor that could be bad? Also, I did switch the controllers between drawers (good instructions on the fisherpaykelparts.net website) but the problem stayed with the drawer, ruling out the controller.


Did it fill with water? could be 1 of your water valves is faulty, or the little filter for the inlet water is blocked. please reply 4 more help. i"m sure i can fix this problem for you. good luck. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hello, I have a problem with our Miele G646SC Plus dishwasher. It starts its cycle OK, draining out any residual water, taking in fresh water and doing the initial rinse. After about 5 minutes it then stops with the "inlet/drain" red light flashing. The detergent is still in the holder and the water is still cold. The filter at the bottom of the compartment is clean, the drain pump spins freely. I've also checked for any leaks in the bottom of the machine that would trip the styrofoam/microsw


Hi\015\012\015\012 \015\012\015\012The light flashing means an issue while draining. You would need to check for air\015\012gap on the dishwasher, it may be clogged. It prevents dishwasher\015\012from drain ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Dishwasher, OKO_Favorit 545i A few minutes after the completion of a washing cycle, the drain pump restarted and continude to work for along a period, and when I switch off at the socket, the RCD switch tripped at the mains. This appened several times. Could you please assist with a possible solution, thank you rof your help Mal James


... AEG Dishwashers

Stopped mid-cycle by blowing fuse. Cannot remove water from machine. Every time I switch on it blows the trip again. I tried leaving it for a while in case water had got into the electrics but after about one second the fuse went again.


Can be the drain valve/ drain pump is faulty and so since it is in this cycle the drain current is too much for the fuse to blow.\012So recheck by disconnecting the valve and putting fuse in , if the fuse stays then it is confirmed. if not the ... Miele 24 in. G645SC Plus Free-standing Dishwasher

Frigidaire Dishwasher model # FDB520RHB2 Stopped prematurely last night while on light cycle, now will not respond at all. Noticed water at bottom of tub; tried draining manually through drain tube, removed lower arm, glass trap, and filter, and water remains; tried electronic reset by switching off breaker for several minutes; all to no avail. Electronic controls (cycle/option select) will not respond at all.


This is not a uncommon problem and it sometime's is the pc control panel but i find that it is more often the interlock ( latch assembly .) i would change // there has been a improvment and i belive this will solv ... Dishwashers

My Bosch integrated dishwasher(model SGV56A03 GB/12) runs through the cycle but doesn't stop at the end of the cycle. It continues to heat water and it sounds like the motor is running even though the time indicator shows 0 minutes. I have to manually switch it off. Any ideas before I call out an engineer. I have checked all the filters etc included in the troubleshooter info anf there are no blockages.


... Bosch Dishwashers

Tricity Bendix DH090 water valve closes too early. Insufficient water causes program to stop before first heating cycle. If I switch off, open the machine & pour an extra pint of water in, shut the door & switch on again the wash takes place and completes perfectly to specification. OK so the problem seems to be that level detector No 1 switches off the water inlet valve early and level detector No 2 (apparently) halts the cycle since it detects insufficient water in the machine. I cannot see t


... Tricity Bendix 18 in. DH090 Free-standing Dishwasher

We have an Hotpoint FDW70 Dishwasher that for some time has had an A10 fault which although stops the machine some times 70% of the time it does a full cycle. However it is now tripping out the electric at the mains. It is not RCD protected, but does not blow it's own 13amp fuse or that of the fused extention lead it is pluged in to. Tends to blow after about 5 minutes. I know about the fault code A10 being 'Fill Valve Triac' but as not an engineer what is that? and what parts are needed and or


Hi the fill valve triac is the plastic vlave that the inlet hose connects to you can get them for about £10 you reset the machine after replacing it by switching it on, pressing the power button leaving it off for about a minute then switching ... Dishwashers

Our MIELE TURBOTHERMIC shows a red indicator light on the topic of: drain/watersupply.when switched off and restarted, it evacuates the water succesfully and commences the cycle but then after two minutes, it stops again with the same message.


Hi,First the unit drains and then fills with water. When the unit has intially drained open the door and manually fill the unit with water, about 5lts. This will then allow the dishwasher to go to the next step which is to circulate the w ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

Hi there, we have had our dishlex 300 dishwasher switched off for a while and today I turned it on. I started a cycle and it stopped after a few minutes and then the Eco button started flashing. I opened the dishwasher to find it full of water and leaking out of the button. Please help! Regards, Pania


Hi just read your posting.Now the reason these dishwashers flash ECO is because there is either water in the bottom tray or your drain pump is open circuit.Is the machine making a pumping noise when it is flashing the ECO light,or is it completely si ... Dishwashers

My built in Whirlpool adg 9340 washer won't start a cycle at all. It seems to start a cycle and after 1 minute it stops and it starts beeping. Also water remains on the bottom. As soon as the cycle starts it drains that water and brings new water in which stays there. It won't work for more than 1 minute....


... Dishwashers

Have a Miele G1220SC dishwasher. It recently developed a strange problem: when switching it on ALL program lights come on and the machine starts taking water. after a while it stops taking water and starts to pump water, all the time all program indicators remain on. if you leave it on a while ( about 4 or 5 minutes) it is impossible to switch off the machine with the main switch, all you can do to stop it is unplug it. anyone experienced something like this and have any idea what part is malfun


Follow this steps and fix it. God bless you\012 \012 Heating Element\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Miele Dishwashers

Hello , we have a blanco BFDWC65 dishwasher supplied to us by our builder , The dishwaser fills with water ok then once in cycle it starts (with all operating lights ) then stops , it continues to start then stop for the rest of the cycle , Quiet some time later it finished and then drained the water ok , now it struggles to get to the end of the cycle. have checked all filters , water pressure and for clogged hoses , everything is ok in that department. Any help would be apprieciated


I would suspect the control board in this type of behaviour. As the machine is new I advise no interference, but to open a claim under warranty. You would have all the warranty papers for this unit, or should have received them from your builder. The ... Dishwashers

My dishwasher SL34A015UC / 29 does not complete it's cycle. The cycle will stop with 1 minute left in the rince cycle and continue to run for hours, showing just one minute left. The dishes are not geting clean and there is a unplesent odor inside. I can hear the water draining during the cycle. The drain line is clear and there is plenty of water in the dishwasher. Any thoughts?


... Siemens SL5A70UC 24 in. Built-in Dishwasher

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

On the MIELE G881 SCI plus -3 the cycle stops after about 2-3 minutes (enough time to purge the remaining water and fill the dish washer with new water). Then after 10 minutes it abandons de cycle and shows the red light "intake - purging". When i open the washer, the water inside is NOT warm.


Hello, Welcome to FixYa.I'll start by saying on many Miele different issues can manifest in a similar scenario, water valve, leaks, etc. and then the error lights. ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher

When I turn on the shop force 1750 electric power washer I get water pressure in intermittent time frames. For example, it may run for a second then stop for ten seconds, then start again for three seconds then stop for 3 seconds then start for a half a second then stop for five seconds etc. until ?. This type of pattern continues for at least ten minutes, which is when I give up. I have tried adjusting the the water hose pressure, high, low. middle, nothing changes. This happen when I have the


The usual cause of this is sticky Orings in the water admitance valve.\015\012\015\012Take the valve apart and clean the bore with crocus cloth wrapped around a rod and replace the Orings and lube with a bit of plumber's grease and reasse ... NIB Shop Force Universal Pressure Washer Accessoriesnib

My top dishdrawer stopped working half fill of water. I put it on rinse cycle and it drained the water. I found a bit of sand in the bottom of drawer. I wiped the sand out and then put onto a cycle. After a couple of minutes the dishwasher started flashing a tap symbol with a slash through it and stopped working. Any help please:) Jacki


... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

SMEG STX dishwasher does not complete the wash cycle, stopping after 3 minutes on all cycles displaying error code E1. The machine seems to start with the usual whirring noise but then stops after 3 minutes without pumping in water. The machine is a few years old now but has needed 2 new control panels already although this does not appear to be the problem this time. Any suggestions? Thanks DW


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2271 seconds