Having problems with your Dishwashers ?

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


Answers :

So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, wait 1 minute and turn power back on and see if it works with this disconnected. If it does you will need to replace this. It is like a sensor that says there is too much debris. Stupid part that was totally unnecessary in the first place. Sorry about the inconvenience.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers

I have a kenmore dishwasher mo. no.665.17039401 the clean green light flashes 7 times and it keeps doing that if i try to start the dishwasher on the start button a red light flashs three times what do how do i fix it .i made shure the door was locked


... Dishwashers

Hello, We need some assistance with our Kenmore dishwasher. Last night after I started a load, the dishwasher just stopped and then the washing and drying lights started flashing red, sanitized and green are flashing green and the 6 hour delay button is flashing red. I have pushed the start/cancel button but to no avail. My husband shut the power from it to see if it would reboot, it does not help either. It runs a little bit then quits and does not clean the dishes. Could you give us sugg


Hold the start button for 3-4 seconds and see what that does ... Dishwashers

Green light flashing and water still in bottom of dishwasher. I have cleaned the filters also I cannot reset the start button it just keeps starting again and then stops and green light flashes again


Hi,If this is the clean light the follow the link below, it will explain the flashing and how to reset the control so you can use the dishwasher again. ... Whirlpool Dishwashers

Diswasher malfunction - won't start clean light flashes 7 times The clean light keeps flashing green. Can't get the washer to start. The only operation it will do, is drain when the cancel / Drain button is pushed This unit is: Stock # 16029 Type # 575-0 Model # 665.16029.402


This information may help in your situation. This can be a common problem on some Whirlpool manufactured dishwashers. The following link explains how you may be able to clear the blinking clean light problem: ... Kenmore 24 in. 16029 Built-in Dishwasher

Hotpoint BC145 Dishwasher not cleaning starts to kick in but then just sticks on the "R" light flashing and cannot reset even after turning off. Itbeeps when pressing the select button sound weaker and shorter than they used to and the light does not move from the "R". On a couple of times I have tried it has reset and then the dishwasher starts but after about 3 minutes there is a low beep(not the usual beep when a programme finishes) and the washer stops and the light is flashing on the "R" ag


... Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

Rinse only light is on and all of the wash rinse sanitize clean buttons come on and flash when you try to start it, if you change the setting to normal or heavy duty the wash light comes on then the rinse only light comes on and all above mentioned buttons flash until the tub is drained.


Hi\015\012 \015\012Try and reset the dishwasher by unplugging it for 5-10 minutes. Now check if you are still getting the same error you can try and press the following buttons to reset it-- \015\012Saini Rinse, He ... Dishwashers

I have a Quiet Partner II dishwasher. The clean button is blinking with a green light. When I try to start is over, nothing happens. When I push the cancel/drain button, I hear something happening for maybe a minute, then it reverts back to the clean button blinking and won't take any other commands. What should I try next?


... Kenmore 24 in. 16222 Built-in Dishwasher

Kenmore dishwasher 665.16029402./ clean light flashes 7 times. i did the push button sequence to reset. started to wash for awhille and during the wash it stops and green light starts flashing again


... Kenmore 24 in. 16032 Built-in Dishwasher

I have a Kenmore Elite Ultra Dishwasher and the cleaning light is flashing. I have tried pressing the start/resume button and closing the door within 3 seconds. I am not able to turn on my dishwasher. I have tried turning off the power for 20 minutes but when power was restored the green light continues to flash and the dishwasher will not work. This machine was installed in May 2008. Help!


If the clean light flashes 7 times, pauses, then repeats...When\015\012the dishwasher doesn't sense a water temperature increase, it will\015\012stop working and lock the functions (clean light flashes 7 times, all\015\012buttons are non ... Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

Hi there. I'm having problems with my dishwasher. Usuaully once loaded, i push the start button, the closest green light to the start button flashes and dishwasher fills/cycle begins. Now, when i push the start button, the furthest green light from the start button flashes, you can hear the motor running but no cycle begins. No water fills the dishwasher.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

I have a whirlpool adp6600 dishwasher. the green light just keeps flashing (i think it's 7 times in a row each sequence) and the cycle won't start. have tried turning it off at the wall, clean


Dishwasher is in fault mode hold start/pause button for a few seconds this will reset the unit run your cycle again if dishwasher faults again call you local service man.good luck ... Whirlpool Dishwashers

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

I have some problems with a Whirlpool DWF 406 dishwasher: The other day, my wife complained about it not finishing a program (just stopped and started bleeping). I saw a post at this forum where it said to clean out the black grid down my the sump. I did that, and then the dishwasher worked fine a couple of times. Today when I got home from work, the machine just bleeped at me and and the green LED light by the start button flashed 9 times over and over again. Does anyone know what those 9 flash


We have the same problem. The dishwasher is 10 years old. In one of the German forums they said that usually it's because the sieve ahead of the membrane has a fine layer of sludge and the pump cannot pump out the dirty waste water. They said that yo ... Whirlpool Dishwashers

Clean light is blinking, have already killed the power, then called to whirlpool and they walked me through resetting it by pushing buttons, however when i attempted to run it after resetting it, it started to run then went right back to the flashing clean light. i tried resetting it again, and ended up with the same result.


You may a a latching issue. d/w not latching properly. How long does it take before the clean light comes on after you reset it. does it fill with water? if so, then your motor may be defective. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

We have a new Whirlpool Dishwasher Model GU3200XTVY3, serial # F00404693 bought in April 2010. Yesterday,when we pressed the "normal" button, it started flashing then when we pressed the "cancel" button, it started flashing also. The dishwasher will not start when we pressed the "start" button. We tried to reset by turning off the power to the dishwasher and then turned it back on. All lights were off and then we pressed the "normal" button and it started flashing again. When we tried to pr


... Whirlpool 24 in. GU3200XTPS Stainless Steel Built-in Dishwasher

Jenn-Air 24 in. JDB1080AWS built-in dishwasher green lights flash on and off on their own sometimes - not able to start dishwasher sometimes - not able to use settings (lights don't light when pushing top setting buttons - dishwasher seems hot about 8 - 12 hours after use = cleans very well though - dishwasher wasn't used much from 2005-2007


... Jenn-Air 24 in. JDB1080AWS Built-in Dishwasher

Dishwasher won't start. Green light beside 'Clean' flashes repeat


I checked the whirlpool tech line on this it said call for service check heating circet check your warrenty for 2-5th year warrenties some parts like control bd touch pads are under extended but youll have to use a kenmore autherized tech sorry ... Kenmore Dishwashers

I have a Kenmore Ultra wash Quiet Guard 3 dishwasher and the green flashing light that states its clean stays on and stays flashing. I can not even get it to start a wash cycle. please help. What is the button sequence that everyone is talking about that clears this? Thank you.


Hi\015\012\015\012\015\012Thanks for using FixYa. To resolve this you will have to reset the console. Do this by closing\015\012the door and press these buttons in sequence...\015\012\015 ... Kenmore 24 in. 15689 Built-in Dishwasher

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher won't start. Clean light keeps flashing. I have tried cancelling a couple of times, and it goes through a 2 minute process and goes right back to the flashing clean light and not allowing it to start. I have already tried shutting off the breaker as suggested by someone but it did not solve the problem. Any other ideas?


Hi\015\012 \015\012Thanks for using FixYa. If the clean light flashes 7 times, pauses, then repeats...When the dishwasher doesn't sense a water temperature increase, it stops working and locks t ... Dishwashers

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to res


... Whirlpool 24 in. ADG7540 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1817 seconds