Having problems with your Dishwashers ?

Maytag dishwasher dwu7702aae. Water will not turn on during the normal wash cycle. Water works fine in the QuickWash mode.


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Maytag dishwasher dwu7702aae. Water will not turn on during the normal wash cycle. Water works fine in the QuickWash mode.


... Dishwashers

I have a hotpoint aquarius df23 dishwasher. when i turn it on for a wash there is no water coming into the dishwasher. i have put water in with a bowl and it works as normal until it drains the water out. my washing machine is plumbed in to the same pipework and it is working fine. does the dishawasher have a water pump that may need replacing????


Most likely you have an air lock in the dishwasher.\015\0121. Refill the salt compartment.2. Turn of the water supply at the mains.3. Disconnect the diswashers water hose from the mains supply.4. Lower the water hose and allow ... Dishwashers

My Kenmore dishwasher model #66515639000 quit working. It was washing dishes just fine one day and then the next the buttons weren't working properly. The pots & pans button was flashing with the cancel button. After searching on your site, I tried to resent the control panel by pressing the normal wash button and the air dry button 3 times then opening and closing the dishwasher. Now the quick rinse button is flashing. Any ideas of what to do now?


... Dishwashers

Hi, my Ge profile dishwasher model pdw9280n00ss changes wash modes on it's own. This is a new problem, it was stuck on normal wash for the last year. It screwed up right after the warranty ran out. The start button and the heat all seem to work. I've seen it jump between the wash cycles on it's own while washing . Is it worth fixing, I feel ripped off on this expensive dishwasher!! Thx


... GE PDW9280NSS Built-in Dishwasher

Our GE model GSD4320Z00B is having a problem with the drain system. I've run the unit in the test mode and it does pump the dishwasher down. The problem is the unit does NOT pump down during a normal wash cycle. The fact that the unit works in test tells me it is not the pump. I've checked all the hoses and drain paths and there are no obstructions, again verified by the fact it works in test mode. Any test that can be used to determine the problem besides replacing parts one by one?


... GE 24 in. GSD4320Z Built-in Dishwasher

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers

Stops mid-cycle I have a MDB7100AWB that has been working fine for the last 7 years. Now all of the sudden it will not complete a wash cycle in any mode (including auto clean). It consistantly stops at 85 on normal wash & at 65 on light wash and then clicks/buzzes about every 3 seconds, like it wants to continue - but never does. Any clues as to what to try? Is 7 years all I can expect to get?


Hi SaviorSound,\015\012\015\012I'm Harvey the Master Plumbr.\015\012\015\012Your question is: You have a MDB7100AWB that has been working fine for the last 7 years. Now all of the sudden it will not complete a wash cycle in a ... Maytag MDB7100AWB Dishwasher

Anyone have experience with a Fisher Paykel double draw dishwasher (model DD24) getting stuck in wash mode? Once it hits exactly 48 minutes it stays there. Only several hours later it cycles through OR you have to turn it off put it in rinse mode to complete. Already tried all the basics (unplugging, no fault codes, cycled through the diagnostics everything good and working). Did the quick diagnostic cycle of 14 minutes and everything cycled through fine. Next step will be to put the bottom cont


... Fisher and Paykel Dishwashers

Our GE Profile (Quiet Power 6) dishwasher is having trouble cleaning our dishes. The top shelf rarely gets cleaned and the bottom is questionable. It used to work fine. We always use Cascade powder detergent on a normal wash cycle. We have hard water. Any advice would be appreciated. I took apart the washer looking for an obstruction but none existed.


The obstruction can be external to the unit. Check the drain at EACH connection working backward from the sink connection all the way to the motor pump outlet hole. Do not forget to dis-assemble the Air-Gap (if installed) and to check the inside of ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

My Frigidaire dishwasher model# PLD2850RDC1 does not work on Normal wash only on China/crystal and pots and pans mode.


... Frigidaire Dishwashers

Frigidaire dishwasher Water does not go through arms, bottom or top, at all (does not wash). You can hear motor running. Pump works fine; discharges water as normal and fills to proper level. Problem just started with no warning; no strange noises etc.


CHECK WATER INLET SOLENOID OR TIMER ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Our Dishwasher Model 13863, has the normal wash button continuously blinking. We are unable to reset it even with turning on and off the circuit breaker. It had worked fine up to this point. When you hit cancel drain button it just starts blinking as well


... Kenmore 13863 Stainless Steel Dishwasher

I have a KDS-18 dishwasher, and had been working fine until recently. Now it keeps going into a Sani cycle even though I have selected normal wash. Anyway to reset the unit?


In your onwer mannual there is a number call kitchen aid they will walk you through the steps to reset your unit ... KitchenAid 24 in. KUDU02FR Built-in Dishwasher

I have a Beko DWD5410W dishwasher. It has been working well for a couple of years now. Last week is stopped during a wash cycle and now when you switch it on, it fills with water to the top of the filters (as normal?) and stops. Nothing further happens no matter how long I wait unless I switch the machine to drain mode. Do you have any idea what the problem could be or how I can go about investigating further? Many thanks in anticipation


Hi, this is a control fault that is localized in the logic sector of the control board. the logic chip which holds all wash programing is damaged. you will need to replace the control asap if possible...thank u rate me ... Dishwashers

I have a Maytag dishwasher model MDBTT60AWW. None of its wash modes will work when pressing their respective buttons. The Fields Service Test functioned normally with the exception of the "heated dry" and "sanitize" LEDs not being lit. Tried to perform the Manual Function Test, but none of the components would operate upon pressing the respective keys for testing their operation.


Hi, \015\012Sounds like either the control board or the keypad.Try removing power from the unit to see if it will reset.\015\012Now try running the diagnostics…RIBBON CABLE CLEANING ... Maytag 24 in. MDBH955AW Built-in Dishwasher

I HAVE A BOSCH SHU5305 DISHWASHER THAT WHEN IT IS TURNED ON IT WILL NOT DRAW WATER FOR THE WASH. IT JUST SITS THERE AND HUMS. HAD A BIT OF WATER FROM THE SINK BACK UP IN THE DISHWASHER AND SPILL OVER ONTO THE FLOOR YESTERDAY. I CLEANED THE DISHWASHER FILTER WHICH WAS COMPLETELY CLOGGED. I THINK THE DISHWASHER WORKED FINE PRIOR TO THIS INCIDENT BUT THIS COULD ALL BE COINCIDENCE. I DON'T KNOW IF I HAVE A PLUMMING PROBLEM OR A WASHER PROBLEM. THE SINK WATER WORKS FINE. I CHECKED THE ON/OFF WATER VA


If the solenoid valve is humming and calling for water, you probably have a plugged screen in the valve, some you can get to and clean, some you have to replace. ... Dishwashers

It appears that water is not running through the dishwasher or that the sprayers are not working correctly. There doesn't appear to be a clog. However, I did find a round rubber "washer" (I think that is what they are called) laying in the bottom of the dishwasher - where does this part go. It was working fine until this wash. The heating element works fine but like I said it appears that something may be wrong with the spray tower. Please advise Model number of Hotpoint: HDA3420Z01BB T


Hi,\012When my wife started complaining about her dishwasher not getting the top rack clean this is what I found and I wrote a tip about it...Dishwasher ... Hotpoint Dishwashers

My bosh dishwasher SHX55M06UC/46 will not drain. A new disposal was put in and the dishwasher drain plug was not punched out and the dishwasher was ran that way. Now it just holds water in the bottom. I've tried resetting or canceling the wash cycle but that doesn't work and the washing cycle works fine. I'm hoping there is a reset or a safety for the pump if it gets clogged.


... Dishwashers

Whirpool Dishwasher ADP5966 Turned dishwasher on. Only light that comes on is normal wash light. Start button is flashing when normal wash light is on. On pressing start button dishwasher does not work


Most likely the door switch is not making proper contact when you shut the door or the Start button is faulty. Needs someone to look in the door panel to fix. ... Whirlpool Dishwashers

The three lights for Pots & Pans, Normal Wash, Econo Wash are all flashing. When I hold the start button down for four seconds, just the Normal light is on. However, once I close the door, all three lights are on again, and the dishwasher does not start. We have tried unpugging it and then plugging it in again. It worked once then went back to all three light flashing. Before this, only the Normal Wash and Econo Wash lights were flashing.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I can't seem to access any previous post dialog that may have taken place but I'd like to help if you can fill me in on whats taken place to this point.\015\012\015\012The scenario you describe i ... Viking DFB450 Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

Kenwood Elite Dishwasher Mod#665.13779 K600 "Normal Wash " light blinks continuously with NO washer action. No other wash modes light up when pressed. Washer does not do anything. However, a couple of times I got it to make a noise as if it was draining, but then nothing happens. Push "Cancel" and it blinks in unison with Normal Wash light. Open door and close it, "Cancel" light goes out and Normal Wash light continues to blink. Have tried various combination of buttons to try to "Reset"


... Kenmore Dishwashers

The touchpad buttons no longer work to select a wash cycle. When I push "Start" the light above "Smart Wash" comes on and the dishwasher operates normally, but I cannot select any other cycles and the light only comes on after pressing "Start", not before. Also, the Options buttons seem to work normally but the delay button doesn't scroll through 2-4-6, it only toggles the light on and off above "4". The item is 15 months old. Thank you.


... Kenmore 13743 Staimless Steel Built-in Dishwasher

My Kenmore Dishwasher 665.16359301 quit working. I flipped off the breaker then back on again. The cancel light comes on and it sounds like its going to drain but theres no water in it. After about 20 seconds it stops and the normal wash cycle light starts blinking. Thats it. I did the reset procedure and it started to work then went back to the normal wash light blinking.


... Kenmore Dishwashers

When trying to start the dishwasher, pressing the Normal wash button, the dishwasher gives a huge clunk and then it trips the circuit breaker. Upon resetting the breaker, I tried the next button over, which is Soak and Wash, and it seems to go thru the cycle fine. Another time I tried the Normal button, but put the left dial on Rinse and it started up, but it would clunk periodically and it seemed to have a 'hot' smell. I'm worried to use it - what could this be? Is there anything else I can try


Hi\015\012\015\012This is a very dangerous situation you must remove from the wall supply and desist from using, such a fault could easily make the casing "Live" and anyone touching it may be killed. You need to discover why this is happe ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2155 seconds