Having problems with your Dishwashers ?

The "clean" button is flashing & none of the other cycles work.

\015 At the end of the cycle, the ''clean'' button stays on until the dishwasher is opened. I opened the didhwasher, emptied it and reloaded. The ''clean'' light won't stop flashing. Nothing happens when I try to start the dishwasher. It is a Whirlpool Quiet Partner I.\015

Answers :

Heated dry and high temp wash
toggle till all the lights light up
then hit cancel
you should be able to turn dishwasher back on
you probably have a bad heater
is it flashing 7 times
take kick panel off and look to the rear of the dishwasher
is anything burned
if the clean light keeps blinking replace your heater
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The "clean" button is flashing & none of the other cycles work.


Heated dry and high temp wash toggle till all the lights light up then hit cancel you should be able to turn dishwasher back onyou probably have a bad heater is it flashing 7 times take kick panel off and look to t ... Dishwashers

Hi, We have a Smeg ST 663 dishwasher that does work. However, sometimes when you want to use it and turn the power button on it beeps twice with the red light flashing and you can't get it to work or change the settings. Sometimes if we leave it for a while and try it again later it will work, but it is annoying as sometimes it won't want to work for ages and we really want our dishes cleaned! The dishwasher doesn't have many buttons on it (a power button, cycle selection button and 1/2 load


Hi,\015\012\015\012Turn machine on and press and hold the programme select button till the light goes out about 5-7 seconds see if this resets it if it does start a cycle and see what happens.Otherwise the pcb as its not responding to an ... Smeg Dishwashers

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

My Frigidaire dishwasher - most buttons don't work and clean and sanitized lights are flashing after cycle completes.


Hello Rich - From what you have described if only some cycles are working, then there seems to be a communication problem coming from the main control panel, I would suggest contacting a professional technician to diagnose the unit. ... Frigidaire Dishwashers

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Countdown display is flashing saying 2:10 but dishwasher does not respond to pushing any of the buttons (light stays on Power Scrub and does not respond to selecting other wash cycles). On'Off button works but none of the other buttons responds. Machine does not begin washing when door is closed


... Bosch SHE6AP0 Builtin Dishwasher

Talking about a kenmore 665.16389300 dishwasher. the "normal wash" button is blinking, but none of the other buttons seem to work and the cleaning cycle will not start when i press the "start" button. any ideas?


Hi\015\012\015\012Open the door.\015\012Within 3 seconds press the following sequence --Try pressing normal wash,\015\012heated dry, normal wash, heated dry, normal wash, heated dry three times within\015\0126 seconds and the ... Kenmore Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Hey, I have an 18 inch free standing SMEG dishwasher that has stopped working. The power and water feeds are fine. None of the cycle buttons are lit up or responsive, however two buttons next to each other are. They are not flashing just permanantly on. Lauren


... Dishwashers

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers

I have a'05 Kenmore Elite dishwasher. Never had a problem before. The clean button keeps flashing. Thought it was an interrupted cycle so I pressed the "Cancel/Drain" button and the motor ran, no water. Once that was done, I tried to start a new cycle and every time I push start, the green clean light flashes and the "Start" button goes off. Any help. Really don't want a repair guy. Thanks in advance


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes, pauses, and then repeats. When\015\012the dishwasher doesn't sense a water t ... Dishwashers

Hi, I have a KitchenAid Superba diswasher model #KUDSO1FLSS2 that has quit working. All the buttons seem to work and the lights light up as they should but when you hit the 'start' button the light that you selected for whichever cycle would flash once, then close the front door and dishwasher would start. The 'start' button was acting up and would have to press a few times before light would flash and then the dishwasher would work. Now everything lights up but start button does not work. Opene


Hi.Test the start button switch.The switch is tested by disconnecting power and reading Ohms, this will tell you if it does open and close the circuit.If the start button is part of the control assembly, then this kind o ... Dishwashers

AS PER DIRECTIONS FROM TECH, I PURCHASED AND INSTALLED A NEW CONTROL UNIT. THIS WAS BECAUSE MY WHIRLPOOL DISHWASHER GOLD GU2300XTLB3 QUIT WORKING IN ALL CYCLES EXCEPT SHORT CYCLE. PUT EVERYTHING BACK TOGETHER AND TRIED TO GET THE DIFFERENT CYCLES TO WORK. NOTHING WORKED EXCEPT THE CLEAN LITE FLASHED A CODE 7.(FLASHED 7 TIMES THEN QUIT. THEN IT WOULD FLASHED 7 MORE TIMES THEN QUIT) iT HS BEEN DOING THIS FOR WELL OVER 24 HOURS. WHAT MUST I DO TO GET BY THIS ERROR CODE AND GET IT TO START W


Hi,This is a common problem with Whirlpool washers.If\015\012the clean light is the one flashing then your dishwasher could have a\015\012heater circuit problem (depending on the age) or this could simply just\015\012be water colder ... Dishwashers

None of the wash cycles are working. The clean light on the right side of washer is flashing


... Whirlpool 24 in. GU1500XT - Multiple Color Built-in Dishwasher

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

I have a Whirlpool dishwasher mod. number GU2400XTP6 the clean light flashes then stoppes when the start button is pushed. the light on the start button flashes three times and stoppes then the clean light starts flashing again the machine dosen't start. I've checked the micro switches in the handle release and they are working fine. will I have to replace the main computer module? If so were do I get it and how much dose it cost?Thanks


... Whirlpool Dishwashers

I have a Whirlpool Gold Quiet Partner III (Model GU1200XTKB0). I have used it previously on "Normal" cycle and I always keep it on Air Dry. Last night I used the "Pots and Pans" cycle and it seemed to work fine. But this morning the Air Dry light is flashing and if I press a cycle key the Rinse Only light starts to flash as well. Nothing works. I have made sure that the console is not locked. Any suggestions? I do not have a Heated Dry button, only Air Dry. Thank you.


... Dishwashers

We started the dishwasher and it started. during the cycle, the soap dispensor didnt open and now it flashes clean. I've tried to cancel sequence, it goes through the draining process but when I go to start, the start button flashes as does the cleanned button. Any suggestions as to hw to reset it. Thanks


Hi\015\012Dishwashers use Bi-Metal strip to allow the dispenser to open/close. This strip when heat up causes the soap door spring to open up the dispenser. If this strip is not heated doesn't allow the door to open. Th ... Sunbeam SNB542UCAS Built-in Dishwasher

Help! My Whirlpool Quiet Partner II isn't working at all. Water was standing in bottom at end of last 2 cycles, but on the last cycle, I came home to clean looking dishes, standing water, and a machine that won't turn on at all- no lights on any buttons- nothing works. I've tried the reset codes published here and elsewhere, but there are no lights on any buttons at all. The circuit breaker is fine. I have 3 young kids and can't function long without my dishwasher!


There is a fuse in the control panel what your model# i can get you the part number its easy to replace it. ... Dishwashers

DISHWASHER QUIT WORKING IN ALL WASH CYCLES EXCEPT SHORT WASH CYCLE. YES I HAVE TRIED TO FIX IT. I HAVE REPLACED THE CONTROL MODULE WITH A NEW ONE. ALL WIRING LOOKS CLEAN AND IN GOOD ORDER. NO EVIDENCE OF CORROSION. NOW UNIT WILL NOT WORK AT ALL, BUT "CLEAN LITE INDICATOR' IS FLASHING IN SEQUENCES OF 7. I HAVE FOUND THE SCHEMATIC SHEET BEHIND THE KICK PLATE. AND USING IT I HAVE TRYED TO USE THE DIAGNOSTIC PROGRAM BUT CANNOT FIND ANY PROBLEMS. AFTER DIAGNOSTIC PROGRAM IS COMPLETE THE DI


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012With the symptom you`ve described ( specifically the clean lite ) this is an error of poor water circulation or a heating fault...many times manifesting in th ... Whirlpool Dishwashers

We started the dishwasher and it started. during the cycle, the soap dispensor didnt open and now it flashes clean. I've tried to cancel sequence, it goes through the draining process but when I go to start, the start button flashes as does the cleanned button. Any suggestions as to hw to reset it. Thanks


... Sunbeam Dishwashers

I'm working with a kitchenaid D/W model N0. KUDS01FKSS1: I repired a broken wire that shorted out near the main board, after repairing the wire the cycle selector board "light wash cycle" was not working, after the customer used the D/W the "clean light starting flashing 7 times then pauses repeately, after instaling the selector board, I entered the diagnoptics code all lights came on and then I cancelled, the D/W started working, when the cycle finish the light will come back and D/W will no


... KitchenAid Dishwashers

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

We have a Bosch SHE44C02UC/46 that suddenly won't start. I pushed the on/off button to start the dishes cleaning on the 'Power Scrub Plus' cycle and the display lights up with a 125 min. indication for the cleaning time, but the dishwasher never starts. It just sits there completely silent and never begins the cleaning. The dishwasher has worked perfectly up to, and including, the last cleaning cycle (3 days ago) for the last 4 years. Suddenly, today, nothing. Zip. Zilch. Nada. I don't get i


Hi.Re:" I\\'m sure it has to be something simple." A: yes, probably a fault, simple as that.To start there is a recall concerning this model. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

The start button flashing continuously and the filter area seems to be full of water but when I take it out it is perfectly clean. I have switched the machine on and off several times but each time the start button indicates a fault. I have tried holding down the on button so as to stop the start button flashing so that I could select a program - this did work once and I selected my program but 10 mins in it stopped and started beeping... I have a ADG7460 machine - HELP! I'm going crazy!


Please clarify what you mean by "..but when I take it out it is perfectly clean.." are you saying the water in the filter area is clean. \015\012\015\012Turn the power off and take out all the water by hand using a small container. Turn t ... Whirlpool Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1719 seconds