Having problems with your Dishwashers ?

Frigidaire dishwasher (Electrolux FDB750RCB0) does not move water through the hose to the upper wash/spray bar. The lower wash/spray bar has pressure enough to turn. With the dish washer out from under the counter I can see the water rise very slowly up the translucent hose. If I remove the check ball under the stem assembly in the motor in the bottom of the tub, water flows, but I'm not sure if the top bar turns then (with the door open I see water coming down from the top, but never saw


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Frigidaire dishwasher (Electrolux FDB750RCB0) does not move water through the hose to the upper wash/spray bar. The lower wash/spray bar has pressure enough to turn. With the dish washer out from under the counter I can see the water rise very slowly up the translucent hose. If I remove the check ball under the stem assembly in the motor in the bottom of the tub, water flows, but I'm not sure if the top bar turns then (with the door open I see water coming down from the top, but never saw


... Dishwashers

My dishwasher has stopped cleaning plates properly. It makes everything wet but at the end of the cycle the detergent block is half dissolved at the bottom. I have just run a cycle and opened the door during this. The bottom is full of soap suds and water and the top spray bar is dripping water after I open the door but when I close and then reopen a few secs later the top spray bar has definetly not rotated. The water is also not hot, this dishwasher is a cold fed only machine so I guess the el


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

NEFF S4443 top spray bar not rotating, no water. Bottom spray bar rotates and sprays water. Checked and replaced fine/course mesh filters. Will pump to empty and refill on pre-wash (rinse). Seems the pump may have two outlets one feeding the bottom spay bar (nearest from of machine) and one just behind which feeds the upper spray bar. Running without spar bars attached (including mechanism feeding to bar, water is only being forced out of the from outlet. Any ideas before I start taking it apart


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

I have a F and P 603 dishwasher with a similar problem as to a recent post here. My top drawer doesn't turn on and my bottom drawer does. Well it just has after I swapped the "blue" motor inside from my top one. Now, I have tried and opened as far as the translucent "X" plastic from the bottom of my bottom drawer showing the motor and it looks fine. I have even swapped the control board from my top drawer to try and see if it works and it actually does. So, problem persists. Top drawer do


Alright, open up the outer panel of the machine. Note the positions of the wires on the switches and\015\012remove them, unclip the switch housing from the base panel. The\015\012switch housing contains one switch for each drawer. The switches are\01 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Bosch Exxcel Diswasher SGS43E08GB/43. Top spray bar won't spin. All arms, spray holes, ducts, filters, etc are clean and free from obstructions. Water comes out of the holes on the top bar but it won't spin. Water pressure inside the machine with all the bars and ducts removed seems good. Bottom bar works fine. Any ideas please?


Try starting the washer, then opening to door and checking the water level in the bottom of the machine, as far as I know, there should be enough water there to disolve the tablet when it sits in the bottom. if not that much, bung in a few cupfulls a ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Frigidaire dishwasher doesn't pump water to the top wash bar


... Frigidaire Dishwashers

My KDI-21A Kitchenaid/Hobart dishwasher does not wash the top rack, but does fine on the bottom. It appears that water is not flowing to the top wash bar. Is is possible for only the top bar inlet to clog somehow? I've pulled the bar assembly itself and the main tube from the wall of the washer to the top wash bar is clear .


... Dishwashers

DD601ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the s


Check for restriction in sump. ie remove rotor, push pipe cleaner or similar from filter sump into rotor sump ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dd601 ver2 Top draw wont drain properly.Leaves about 2 inchs of water(clean). Occaisionally u3 code shows.Have tried eveything i can think of. HP is correct Drain hose and filter to pump are both clear. No blockages. Have swapped motors from bottom to top and makes no difference. Have swapped inlet hoses around and no difference. Have run diagnostic and when in drain mode P2 it drains very slowly - takes 1 minute 42 seconds to drain 2 litres of water. Bottom draw takes just 30 seconds to do the


I had the problem with the top draw not draining properly and the dishwasher showing the U3 fault code on my DD601 v.1, I did'nt have a copy of the dishwasher manual so it took the following steps, this is best done out side to save on messing your k ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a MODEL 577-0 kudk01ILb55 KITCHENAIDE dishwasher. I am trying to remove the inner pplastic bar that goes vertically through the system from top top bottomj so that I can clean out the filter. But I do not see how to remove that bar. I have looked online for a repair manual of some type but have been unsuccessful. Can someone tell me how to remkove the bar so I can get to the filter on the bottom? I have already removed the star shaped rinse sprayer.


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Hi I have a Nemo Dishwasher and the top spray arm is not turning. The bottom one is going fine and there is certainly plenty of water getting into the washer as I opened the door with the washer going and it flood me. I can see the water getting into both spray arms - the bottom one has a excellent upward spray and turns - the upper spray arm has water getting into it but it will not turn. I have cleaned the dishwasher out and any internal parts that I could find so it is spotless - this is so f


... Fisher and Paykel DS602 Dishwasher

Water doesn't come out of spray bar. water fills dishwasher (and can drain), it also gets heated. But the spray bars won't spray any water (top or bottom). Any ideas?


There is a pump that sends the water to the spray bars. I believe it is broken. Perhaps there is a jam but I don't think it is possible because the water is filtered before going to the pump. Anyway. The pump may need to be replaced (n ... Kenmore Dishwashers

I have a GE potscrubber Dishwasher Model # GSD3630ZZ3WW it has been leaking from the bottom for about a week. I took the bottom off tonight and ran the dishwasher so that I could see where it is leaking from. It is not a hose but the leak seems to be coming from the back of the motor or pump fan where it goes into that plastic housing that attaches to the bottom of the dishwasher seems to be leaking in the very center of that housing where the motor shaft enters the housing. Water is just spray


... Dishwashers

The top dishwasher is flashing F1 and the motor won't turn off. It will drain if I pour a cup of water in it. The bottom dishwasher is working just fine. There is no water in the bottom pan. I usually find a few drops of water when it's flashing F1. Thank you!


Hi.the troubleshooting, and the error code depends on the make of the dishwasher.If the dishwasher does not stop draining, then the float sensor switch, or the pressure switch in the drain system is faulty.Details ... Dishwashers

Recently our GU1100XTLQ1 started having a problem. It barely cleans the bottom rack, and barely gets top rack wet. The soap stays stuck in the dispenser. I can't see inside as it runs, but my guess is that not enough water is being shot out of the various spinning arms. From looking at diagrams it would appear that this dishwasher uses a pump to circulate water from the bottom of the cavity through the spinning arms. Is my problem a dying pump?


... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

We purchased an expensive top of the line Fisher and Paykel 2 dryer dishwasher when we did a total Kitchen rehaul over 1 year ago. We have been noticing water sitting in the bottom of the bottom drawer that smells like sulfur dioxide and now see water is making its way through the maple cabinet to below the sink. None of the plumbing under the sink is leaking. We also purchased a Fisher Paykel gas oven/range at the same time. We notice the oven does not appear to close completely with a tigh


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If you have water leaks around the base of your dishwasher,\015\012you may be using a detergent that is ... Fisher and Paykel Dishwashers

Does not get my dishes clean, leaving a film on my glasses, not getting food off. tried to take apart to clean but could not figure out how to get bottom filter out with the large water bracket going up the back of the dishwasher to the top water bar. I bought as a store model, no instruction booklet. How do I clean out bottom filter?


The problem is hard water. www.dishwasherfilter.com has a product to solve this problem once and for all. It filters the water going into your dishwasher and removes the ... Jenn-Air 24 in. JDB1100AW Built-in Dishwasher

No water pressure coming out while ingine is running. hoses/ attachments not clog. Pulled and opened pump, didn't see anything broken although noticed pump was filled with oil/lubricant but about 1/4" below top surface. Is it suppose to be filled to the top? What kind of oil is used on the pump? And how come there's no water pressure coming out while the motor is running and handle trigger engaged?


If you can find the model # then you can call tech support for free advise.\0121-888-279-9274 ... Karcher Pressure Washers

The water is not getting up to the middle spin bar or the top one, so nothing on the top rack is getting cleaned and everything is left with soapy film, so it is not rinsing properly. There is water coming in at the side for the intial fill and from the bottom to wash.


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

My 12 yr old KitchenAid -Sculptura-Model KUDR24SE starts to fills with water and then does nothing else. It will eventually go through the cycles on the panel, but nothing is happening inside. End result is still dirty dishes with water sitting in the bottom that has to be baled out. Cups on top rack don't have any water on the indentations, so it's obvious that the thing filled with water and that's it. I had the motor replaced (supposedly with a new) one 2 years ago so I find it hard to bel


... Dishwashers

Water does not spray up to the top rack - dishes not getting clean. Lots of water pressure; lots of water in bottom; motor spinning; no apparent damage to pump impellers. Any ideas? Maytag MDC4100 freestanding. Thanks.


... Maytag 24 in. MDC4100A Free-standing Dishwasher

My chef classic dishwasher is not completely cleaning the dishes. There is no obstruction to the tablet/powder door opening, although there is a small amount of powder left at the end of the cycle. Both top & bottom spray bars are clear & rotate, the water is heating & there appears to be plenty of water getting water into the machine. Drain filters are also clear.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Magic Chef CDB6100 Built-in Dishwasher

Follow-up I've removed the lower arm, I'll spend some time and see whether I can get the pobem sorted out. My wife noticed the the detergent was smeared all over the door and repeated tries didn't get it out. Therefore, the water is not spraying. I can confirm the water is filling on the bottom and draining. The heater is working well. I am thinking there is no pressure to send the water through the tubing to the upper and lower arms. The motor is hot to touch (118 degrees with my temp probe). I


... Kenmore 24 in. 15199 / 15194 / 15192 Built-in Dishwasher

Magic Chef DU2000 won't fill with water- no water spray at top or bottom. Sounds like the motor is running, but no water!


Float stuck or bad fill valve,valve screen plugged with sand, water line kinked,remove valve and clean screen.put back on dishwasher make up a test cord and see if it will fill if so hook back up and run dishwasher ... Magic Chef 24 in. DU2000 Built-in Dishwasher

Dishwasher leaking my GE Natulus dishwasher is leaking from the bottom seal, Is the two pieces that are at the very bottom that hold the motor where the seal is? I'm not seeing a seal. I'm not sure if that is where it is leaking. I've got the thing torn apart so it is difficult for me to say where it is leaking. I'm going to give it a whirl. Don't know if the repair is worth the trouble. The GE dishwasher is only 7 years old. What is the avg life of a dishwasher. I'm sure it's not top of the lin


There is a front door seal that may be the issue. It seals along the door sides/top and continues under the door to seal the bottom surface when closed. Mine pulled out of the seal channel under the open door where you can't see it without a small mi ... GE Nautilus 24" Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1376 seconds