Having problems with your Dishwashers ?

We have a Fisher& Paykel dishwasher with 2 drawers -- one on top of the other. Model DD603. The bottom drawer works fine. But the top drawer is not working properly -- it repeatedly stops in the middle of the cycle and there is water left in the drawer. Previously when this happened, we called a repairman; he removed the top drawer from the machine, said it was "off track", flipped some lever, and put the drawer back. He seemed a little embarrassed by having to charge for a service call for


Answers :

Are you able to provide a bit more information on what you see when the dishwasher stops in the middle of the cycle -
\015\0121 - is it displaying the time remaining in the cycle and is it always the same time?
\015\0122- do you get any fault no. or beeping when it stops
\015\0123- what is the temperature of the water in the drawer feel like - cold/ hot.
\015\0124- do you hear any unusual noises when the unit is operating (compared to the bottom drawer)
\015\012
\015\012You can post a comment with the above information and I look forward to providing some solution to the cause of your dishwasher problem.
Hi
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks\015\012for using FixYa. Switch of the unit and unplug it from the power socket\015\012and mains. After more than four hours plug it back in the power socket and\015\012switch it on. If still the issue is not resolved then please check that the drain\015\012hose(s) are not bent or kinked. If so then clean and straighten the drain\015\012hose(s). Also check that the filters are not blocked. If so then clean the\015\012filter plate/drain filter and unblock the drain hose(s). Otherwise this issue\015\012can also be either due to a faulty door latch or door lock switch which is not\015\012engaging itself. And, if the door latch will not engage the dishwasher will\015\012sense it as open door and will not start the cycle. And the sound might be\015\012coming from the door lock solenoid (a hum/buzz sound).
\015\012\015\012
\015\012\015\012The light\015\012also blinks when the dishwasher detects a no-fill\015\012condition. You’ll need to get access to the fill valve by removing left\015\012panel, look at back to see where valve is when you get to it remove one of the\015\012wires and set meter to ohms setting and put a lead on each tag on valve. The\015\012reading should be about 3.6k ohm. If you don’t get a reading then the valve is\015\012at fault. I'll also suggest you to check the detergent dispenser\015\012solenoid for this issue. Remove the door panel and see if there is a round\015\012item at the dispenser assembly with two wires attached to it. Put the\015\012dishwasher into a cycle and when the noise appears, gently press on the\015\012solenoid to see if that is where the noise is coming from.
\015\012\015\012
\015\012\015\012Please do\015\012accept the solution if the issue is resolved or else revert for further\015\012assistance.
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks
\015\012\015\012Rylee
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a Fisher& Paykel dishwasher with 2 drawers -- one on top of the other. Model DD603. The bottom drawer works fine. But the top drawer is not working properly -- it repeatedly stops in the middle of the cycle and there is water left in the drawer. Previously when this happened, we called a repairman; he removed the top drawer from the machine, said it was "off track", flipped some lever, and put the drawer back. He seemed a little embarrassed by having to charge for a service call for


Are you able to provide a bit more information on what you see when the dishwasher stops in the middle of the cycle -\015\0121 - is it displaying the time remaining in the cycle and is it always the same time?\015\0122- do you get any fau ... Dishwashers

The dishwasher was recently removed for floor refinishing and reinstalled. The bottom rotor works but the top rotor does not. I asked the re-installer, who worked for the moving company, if he had connected everything properly and he said there was just one water line going into the machine and assured me he had connected it properly. Is there something else that needs to be done to make the top rotor operational? Thanks. John M


... Jenn-Air JDB3610 Built-in Dishwasher

Just looking for some advice on removing the drawer from my servis washing machine, sorry I dont know what model it is. I need to clean the powder drawer but cant find any way to remove it from the machine. There is no internal part marked push that i can see and im wondering if i need to unscrew the four screws around the drawer. Help please! Cheers


Send an email to this address asking for the user guide for your model \015\012\015\[email protected] ... Servis Dishwashers

Fisher paykel Hi I have a fisher paykel dd603 dishwasher. when I run the bottom drawer on its own ,,it also fill the top drawer with water ! so after the dishwashing cycle , im left with water in the top drawer. im guessing that a valve should close on the top drawer to stop this happening? is there a part I could order and replace myself? thanks [email protected]


Check your email ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

The top drawer is leaking apparently from calcium and/or lime deposits on both the top of the drawer and the rubber gasket on the lid. I need to get the drawer out but can't see where to disconnect the hoses to allow for drawer removal.


There are small tabs at the front of the drawer.. one on each side, down at the bottom of the drawer... push in on those tabs. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Middle and top spinners do not spin The pump is pushing water up the back delivery tube. There are no dishes in the unit and I was able to trick the door into thinking it was closed so I could watch what was happening. Or Not Happening The spinners are completely free of calcium or soap build up and both top and middle are easily spun with a finger. While the pump and bottom spinner were working, I pulled the top drawer out partially and there appeared to be a good flow of water coming out of


Hi,\015\012 Remove each spray arm and check it is clear of food particlesat the jets. The next problem may occour at the rotating joint . If the seal is not good, you can loose a lot of water out of this point.. If both of these seem reasonable ... Dishwashers

Fisher Paykel top drawer lid interferes with opening and closing of drawer. Have top drawer removed for inspection. What to look for?


... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

BOSCH SGS46M78AU Help. How do I remove the top to my machine so that I can get it under my existing work top.. I can't seem to figure out how to remove.


Its like your cabnit draw \015\012lift litle up when that all is up ... Bosch SHU3305 Dishwasher

Fisher Paykel Double Drawer DD601v2. Half way thru a cycle the alarm went on both drawers even though the top one was not inuse or switched on. The error on both drawers is F1. If we push the power button on both after a few seconds they both start up making a whirring noise and both drawers flashing. We have to unplug the machine to stop the irritation. What is wrong and how can we mere mortals fix it ?


Hi,The F1 error means that the sensor that is located in the pan at the bottom of the machine has sensed water.It does not want either machine to run with a leak so it will shut down the operation of both drawers. ... Fisher and Paykel Dishwashers

I HAVE A TWIN DRAWER MACHINE ABOUT 5 YEARS OLD THE TOP DRAWER IS WASHING DISHES BUT LEAVING WATER IN THE BOTTOM OF THE DRAWER WHICH I AM NOW HAVING TO EMPTY MANUALLY HOW CAN I FIX THIS PROBLEM


Have you tried running the rinse cycle to check if the water drains out?\015\012\015\012If you are not getting any fault codes, then it might be simply a matter of cleaning the base filter plate and the sump. The user manual will tell you ... Fisher and Paykel Dishwashers

DD603 Double drawer dishwasher: How do you take the clear coverplate completely off the top drawer in order to replace the motor? I can't figure out how to remove the part that attaches to the front of the drawer.


I am assuming you are fully conversant with the unit and have taken out the drawer from housing rail.\015\012\015\012To get the wiring cover off you then have to..\015\012Carefully release the four wiring cover clips from the fro ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

I have a Fisher and Paykel dishdrawer model ds603. Not sure eactly what happened but my son says that the cycle stopped last evening (and only tells me this morning!). Dishes though appeared to be clean and there was a small amount of water at the bottom. I tried opeing the washer and it was hard to open as though the drawer was stuck on something. I removed the drawer and checked the rollers and they are fine. I realised then that the drawer is getting stuck on the inside lid that provides the


The best thing to do is to remove the rack,drawer completly,and close it up,see if it will come on,and run all threw the cycle.If it does,then put the rack,drawer on the track.The rollers could be,well,not snapped all the way on.It will be in that ar ... Fisher Dishwashers

On my dishwasher a MDD8000AWS the bottom drawer does not feel drawn in like the top drawer. When I took the drawer out it only seems to be pulling in on the left sided track.


... Maytag MDD8000AWS Builtin Dishwasher

The bottom drawer on our DSC 2 drawer built in dishwasher does not clean on any setting. The top drawer cleans just fine. It's not the removable filters as we have made sure they are clean.


... DCS DD-124PH Built-in Dishwasher

I have a fisher & paykel dishwasher. It has 2 drawers and the top drawer is stuck. It will open if I force it, so i'm using the bottom drawer. It just recently happened. Is it hard to fix?


The lid seal of the top drawer is broken or has come off. To get to it you will have to take the two drawers out carefully along with the cables and hoses intact.\015\012\015\012Then feel the top underside of the cabinet for the lid seal. ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Our 2470scvi has caused all of our glassware to turn white. we use very little soap and we always use rinse aid. It seems to me that it is not rinsing properly. It actually has a sound for about 10 seconds that sounds like a motor is stuck.. This sound occurs twice in each cycle. It seems to wash ok but not great of which I would expect for a supposedly top of the line machine. This problem has always happened and the machine is 3 years old.Is this normal for a miele? If so its not the machine w


Hello macit. I do not blame you one bit for being disgusted about this machine. Let's do this. Empty it out and pour in 2 fulll cups of white cider vinegar. Close the door. Let the hot water run into the kitchen sink until it is as hot as it wil ... Dishwashers

I have a Braun combimax 650--it is fairly new. It was working fine last time I used it, but this time, the dial that turns the machine on seems to be stuck. The little button for the pulse does work. I read the instructions, which said that this might happen when the machine overheats and to wait fifteen minutes, but it is definitely not an overheating problem and the last time I used it was weeks ago.I love this machine and now need to use it for quite a number of things--any help you can provi


... Braun K-650 CombiMax Foofs Processor FOR 110 VOLTS

Removal of worktop top to machine


... Bosch SHU3305 Dishwasher

Top drawer seems to off track, tough to close, etc


Check to see if wheel rollers are broken . Or off track . Then if off track allign it . ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Jackson jp-24b purchased this machine used, cant figure out how to work it. I flip the auto cycle on, and then the power switch. The fill light turns green and i assume water is filling up in the machine. In the meantime there are two small red external hoses that hot water comes and i currently just have those hanging in the sink. At the same time, nothing is happening during the wash cycle, the wash gauge doesnt even move only the rinse gauge. Also when i try to drain it nothing happends (begi


It needs a new drain relay box 120 volt the drain is stuck open the jp 24 were not very good machines the red lines are drain lines if you plug up the drian lines at fillup the machine will wash but now it will never drain a new drain box is not c ... Jackson JP-24B Built-in Dishwasher

Top drawer would not open. I got it open unplugged unit and now it opens and closes fine but the lock indicator is on and the drawer will not turn on. When i press the Lock button nothing happens.


The child lock has engaged. Press the lock button for 4-5 secs and hopefully it should disengage.\015\012\015\012Please post a comment to say if this helped.\015\012It would also be helpful to know under what conditions the drawer l ... Fisher and Paykel 23 in. DD-603 Built-in Dishwasher

Hi, I've got a Fisher & Paykel DD603i which is very nearly 3 years old. The top drawer runs through its cycle and end with a continuous beeping, and some water left in the drwaer, although the dishes seem to be cleaned OK. I have folowed step 2 on page 7 of the manual as described in your response to a similar-ish problem, but didn't completely remove the drawer (as I wasn't sure how to get the clear plastic cover on the electrics underneath). However, at this point I had already disconnected t


Hi,Does it show Error U1 on the display. If yes, follow the below. I am hate to say, however user manual does not contain all the details.If that would have been the case, there is never a need to service manuals, bulletins or even tech's ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

We ran a cycle with 'Lemi Shine' a hard water treatment (Lime remover). After that cycle, the tub will fill and drain, but the water does not reciculate. So, I assume the deposits loosened and then clogged either the recirculation pump or a sensor that activates it. I don't know how to determin that or how to access the senors/floats. I do know if it's the pump that's clogged, I have to remove the thing and flip it on its top to access, but don't know the details.


Hi. Both the drain hose and recirculation hoses should be checked, asap. These hoses are connected to the pump assembly and they can also both become obstructed, as well. I would purge these hoses and check the pump filter and fine particle screen fo ... Bosch 24 in. SHY66C05 Stainless Steel Built-in Dishwasher

We have a fisher Pakel dd603 2 drawer , the top draw wont close so we r trying to remove it to see what is blocking it can't figure out how to take top draw out


Hi!There are two small clips down in the front of each drawer, one on each side. You depress these clips/tabs which are attached to the drawer slides, and then the drawer can be lifted away from the rails. You need to be very careful not to dam ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dishwasher FDB4315LFC0 Error code ER uo Second time it has happened. First time, a repairman came and said I needed a new "vent assembly", but I asked if he could "un stick it," so he took it apart and fiddled with it, and it worked for about a month. Now the error code is back, and he warned that if it came back, I should have it replaced. I've only had this NEW machine 10 months -- this shouldn't happen, right? Any suggestions? Thanks.


Who's to say what should or shouldn't happen?Sounds like you need a new vent assembly. ... Frigidaire Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0848 seconds