Having problems with your Dishwashers ?

Indesit 535 runs all programs but water fails to heat


Answers :

Heat element damaged or a wire intrerupted or the termostat is out of function. call asistance
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Indesit 535 runs all programs but water fails to heat


Heat element damaged or a wire intrerupted or the termostat is out of function. call asistance ... Dishwashers

Whirlpool DWF417W, Type 12155 A couple of weeks ago the machine failed to empty, leaving dirty water in the machine at the end of the cycle. Start a new program it emptied & all was then well. A couple of days ago we started a wash cycle as normal, shut the door, the pump normally runs for about 10 seconds then the cycle starts. However the pump just runs continuously?? After looking here there seemed to be a few links to the subject of water being in the base & the anti flood switch being ac


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

Asko D1996 Dishwasher - Tank fills with water but it "washing" cycle never starts. However, the heating element begins the work and with no water running over the heating element it smells like something is burning. I have tried changing the programs from Pots and Pans to regular wash but the same results. Nothing happens


... Asko D1776 Stainless Steel Built-in Dishwasher

Upon selecting a wash cycle and closing the door the machine starts normally (heating water stage) but never clicks to allow water in and wash the dishes. Fails to advance to the wash cycle and just runs without doing dishes. There was water in the bottom after the last wash, filters are clean?


... Bosch SHV46C03 Built-in Dishwasher

I have an Indesit IDL500 dishwasher. It had stopped heating the water up, it looked as if it had short circuited and so i replaced it, i have power going to the element. A couple of forums state that it may be the pcb behind the timer/selector switch. Does this pcb control the program selection and heating of the element? or is there a thermostat that controls the stop and start of the heating element? Any help would be greatly appreciated


Hi\015\012\015\012The unit\015\012has two thermostats and you can test both of them for continuity before\015\012replacing, no continuity replace the thermostat. Hope\015\012this helps...please post back fo ... Indesit 24 in. IDL500 Built-In Dishwasher

I have a Diplomat ADP8242 Dishwasher that continues to run during its wash cycle. The machine starts and heats up correctly but will not switch to its rinse cycle and just keeps running with 2 intermitent beeps. I have tried to reset the programe which does pump the water out and resets the control panel, but unfortunatly does not clear the fault. Can you help?


... Dishwashers

HI dishwasher will not drain if i remove all the water will run thro cycle and stops with a couple of cms of water left have tryed to find filter inside and failed, removed sides and can see a pump on right hand side can turn impeller easily, is this the drain pump? if not how do i get at pump and or filter. is it possible that plastic chamber on left hand side could be blocked assume this transfers heat Robert


... Bosch 18 in. SRS55L02 Logixx Slim-Line Free-standing Dishwasher

Hi, for the last couple of weeks my Indesit 63 has not always been emptying water at the end of the cycle. Then this morning there was a bang, & some smoke from the control panel. turned it off but then turned it on again and it was running but not heating the water. Can you advise me please?


... Indesit 24 in. D63 Free-standing Dishwasher

My Bosch integrated dishwasher(model SGV56A03 GB/12) runs through the cycle but doesn't stop at the end of the cycle. It continues to heat water and it sounds like the motor is running even though the time indicator shows 0 minutes. I have to manually switch it off. Any ideas before I call out an engineer. I have checked all the filters etc included in the troubleshooter info anf there are no blockages.


... Bosch Dishwashers

Dishwasher cycles through all programs but will not drain or turn off at the end of cycle. I do not know if it drains inbetween. It just continues to run on 0 minutes and when I turn it off and open there is standing water


Underneath the machine there is a donute shaped styrofoam item called a flood safty switch .makke sure there is no debri underneath..mice will drag animal food or chew on this and will lodge it leaving debri under it causing it to trigger a false flo ... Bosch 24 in. SHU43 Built-in Dishwasher

Bosch SGI4345AU/17 shows 2H on the display, it does not seem to matter which program is selected, the unit runs continually. It does not heat the water or finish any cycle. The washing tablet covers the dishes and is not rinsed off. Any thoughts


The Control unit on your Bosch has a burnt out heat circuit. Just about every dishwasher has a number of "thermal holds" during the wash and rinse cycles in which the controller waits for the water to be heated to a specific temperature ... Bosch Dishwashers

Hi, I have a Kitchenaid KUDI01TJWH0 dishwasher that failed. Any of the front control buttons like Heavy-Normal-RinseOnly or even the HiTemp-EnergySaver .... when you press any of these, the corresponding light for it will blink three times and go off. Normal operation that light for that button will come on and stay on. but none of the lights stay on. If you press start, the 'water heating' light will come on and you will hear the pump run for about 10-15 senconds, and then everything goes off


Hi Your Problem is Probably The Control Panel. Not The Electronic Control. The Plastic Piece Across the Top of the D/W, Which Tells the Control What to do But You Must Realize These Parts Can Be Very Expensive. John H. Been in this Business 35 Yrs ... KitchenAid Dishwashers

Dishwasher problem Indesit 320 dishwasher will not run through the program. It fills up starts washing, & continues washing. Fills with water & will not empty or dry. I have checked & the waste is not blocked. Have had a good feel around the bottom (internally) & there do not seem to be any obstructions. Can anyone help? Could it be the "control module" if there is such a thing? Many Thanks


Try taking the drain pump off, easy job just tip machine back remove 3 screws from front of base then remove the single screw from pump and twist to remove check impeller is free to turn chances are its not and is probably jammed with broken glass or ... Dishwashers

I have a zanussi ZSF2440s dishwasher, runs a program ok but wont heat water or dry, heater and wiring all ok, have changed controller but fault still persists


Looks like the program detects the water is already heated. Have you checked the thermostat element?\015\012\015\012Please post a comment so that I can help you further. ... Zanussi Dishwashers

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

I have a Siemens SE25A836GB/35 dishwasher. the program is running and it sounds as if the pump is running all the time. I have tried resetting the program but to no avail. I have checked the filter CLEAR and the water supply is okay. The display in the front which state time to run on the program is blank can you solve the problem?


... Siemens 24 in. SE25A836GB Hi-Line Free-standing Dishwasher

Kenmore Elite Stainless Steel 24 inch tall Model 66577963K701. The heating element works for "heated dry" but not for "Hi Temperature" wash. It used to do so and when I opened the door a nice blast of steam would come out. My hot water tank is a great distance from the washer so we usually run the hot water tap in the sink for a bit until hot water comes... but the heating coil no longer kicks in on any of the cycles (Smart Wash / Normal Wash ). The high limit switch works and as I said, th


... Kenmore Dishwashers

My dishwasher DW60 does not complete the program and drain the hotwater leaving hot water in the bottom of the dishwasher however when I run a prewash cold water cycle the water does drain away and the dishwasher program works correctly do you know why it drains cold water okay but not hot water


... Dishwashers

We currently replaced our water heater, after we replaced it all our water is running fine hot and cold, and i went to turn on my dishwater and no water is running, we checked the valves and everything is opened but when i opened it up it was heated up and no water was going through can you help!


Hi,Reach inside your d/w and jiggle the mushroom shaped float switch\015\012located on floor of d/w. should move freely up and down if its stuck\015\012up(or something lodged under it your unit wont fill with water)....Check a ... Asko 24 in. 1805 Built-in Dishwasher

Leaking from under dishwasher. Has run great since 1996. Under counter model in manufactured home. Chnaged to drop in pellet dishwasher detergent and it ran great. There is no water inside the dishwasher circular drain. We never use the heating coil to dry the dishes. We have turned off the water supply line under the sink to the dishwasher. Cool clear water is running out from under the bottom right corner. The hot water heater is right next to it and everything is dry and warm under it which i


Hi,Depending on the model you have this could be a couple of things. The most likely suspect is the water inlet valve. What I would recommend to do is take the bottom toe panel off, typically there are either 2 or 4 screws holding this pa ... Dishwashers

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

SORRY FOR MY ENGLISH .I HAVE A FAVORIT 54750 WHEN I START ANY PROGRAM IT FILLS NORMAL WITH WATER AND THE MOTOR BEGINS AND RUNS BUT AFTER A FEW SECONDS THE LIGHTS VORSPULEN-REINIGEN-SPULEN STARTS WINKING I HEAR AN ALARM SOUND AND THE PROGRAM STOPS. THE MOTOR HAS TWO YELLOW WIRES THAT TELLS THE PROGRAM IF THE MOTOR RUNS .I TRY TO MEASURE THIS WIRES WITH A MULTIMETER IN OMMS AND SEEMS NO CONNECTION BETWEEN OF THEM.


... Stainless Dishwashers

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1713 seconds