Having problems with your Dishwashers ?

NOT ENOUGH WATER FILLING UP IN WASHER. EVERYTHING ELSE WORKING BUT DISHES NOT GETTING CLEAN AS NOT ENOUGH WATER RELEASED INTO WASHER AT START. WHEN I ADD TO POTS OF WATER IN THEN WORKS FINE??


Answers :

The presostat or whater level sensor is not good
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

NOT ENOUGH WATER FILLING UP IN WASHER. EVERYTHING ELSE WORKING BUT DISHES NOT GETTING CLEAN AS NOT ENOUGH WATER RELEASED INTO WASHER AT START. WHEN I ADD TO POTS OF WATER IN THEN WORKS FINE??


The presostat or whater level sensor is not good ... Dishwashers

My Asko D1606 doesn't seem to be filling/retaining enough water to pump actively through the swing arms. When I add a litre or so of water in manually and hold in the door catch, I can see it appear to start working properly. The tablet is still sitting on the bottom of the dishwasher after the cycle has ended and the dishes are still dirty. The pump sounds all right and it is emptying fine. Also, probably due to the lack of water, the cutlery basket has melted right through, and I am sure any p


Check to see it the dishwasher has been pushed back ever so slightly. The water coming into dishwashers and exiting are on timers and if the hose is pinched this can affect it. Your dishwasher may appear to be in the same place but just pull it forw ... Dishwashers

My dishwasher does not fill with water but if you add water as the washer cylces it works fine. What could be the cause of not releasing water into the dishwaher?


Sounds like pump has packed up,switch of electric and unplug open back of machine see if pump drive belt has come off or is damaged its quite a common fault ... Dishwashers

Pressure Washer I have a Porter Cable pressure model no.PCH2401.It works fine for 5 minutes,then I can hear the motor loading down and then it stalls out. I tried to start it and it was very hard to pull on. disconnected the water supply and if was very easy to pull and started right up. I noticed the pump was very hot.This unit has a thermal relief valve on it,shouldn't it have released when it gets to a certain temperature .I was thinking maybe this is why it might be shutting the motor


Any leaks from connection at pump to gun and wand assembly if so the valve is detecting leakage and open up again without u squeezing trigger it builds up in the head.if your trigger gun is leaking internally then you will need to replace the gun thi ... Pressure Washers

The washer cycle stopped without warning, i thought the timer or the timer motor but it is not the timer works fine and so is the motor. but the timer motor runs til the washer motor starts than is the timer stops and the washer is working but not cycling so no rince or drain or soap etc... just pumping water. if you can tell me what might be the problem, thank you. like i said the timer stops when the washer motor start.


... Jackson JPX-300L Dishwasher

North star petrol pressure washer. working fine, then no high pressure, checked water feed, water filter , pressure relief valve and gun nosall well work sometimes and keep working, when you release the trigger and try in again the pressure gone again. please help, many thanks, richard


Sounds like the regulator is sticking or is airbound. loosen the water connection and then tighten it back. Could also be that the trigger gun is faulty or needs adjustment. Hope this helped ... Karcher 2500 PSI Pressure Washer

Briggs and Stratton pressure washer will not start. I have a 6.75 hp pressure washer that is only a year old. when I pull cord it turns over but does not start. I changed plug and checked it, I have spark when pulling. I have 40-50 psi of compression when pulling also. gas was drained and is brand new. it was working fine last time it was used. I have tried starting it without the water line or spray wand hooked up and no difference. After about 10 or 15 pulls, can smell gas when I am trying to


Hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,, ... Briggs & Stratton Pressure Washers

PRESSURE WASHER RUNNING BUT NO WATER COMES OUT WHEN YOU PULL THE TRIGGER??? IT WORKED FINE WHEN I FIRST STARTED IT. I THEN SHUT IT OFF TO MOVE IT. WHEN I STARTED IT BACK UP, IT STOPPED WORKING.


The water admittance valve is stuck. The spring loaded valve lets more water into the pump when the pressure drops when you trigger the wand. Take the valve apart, clean the bore with crocus cloth on a dowel rod. Replace the O Rings and lube with ... Pressure Washers

I have a McCulloch FH160B power washer and it no longer builds up pressure. I haven't used this very much at all. I tore it apart and cleaned everything I could find. When i pull the trigger for the spray nozzle, I get line water pressure. When I release the trigger, the power washer sounds like it starts to build up pressure. When this was working correctly, the pump would shut off when the trigger was released. Any suggestions?


... McCulloch Pressure Washers

I have the Kitchen aid KUDS01DL dishwasher. It was working fine until last week. When starting a cycle, the washer fills with water. Once filled, the motor makes a humming noise and does not circulate the water. I end up stopping the cycle and the discharge pump empties the water. I took apart and cleaned the basin this morning. I did find some random garbage but it did not seem blocked. Do you have any ideas?


... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher

GLD6260L00SS My dishewasher is not filling up with enough water to turn the middle and upper arms. When I add an additional quart of water during the wash and rince cycles, it works fine. GE service has been out and replaced the inlet valve, arms and computer board and it hasn't helped.


... GE Dishwashers

Hi, I have a bosch SGS43E02Z dishwasher that dont seem to wash clean. It would seem that some times the presure from the spinning washers arnt working well enough as it dont even move rice from plates stacked next to each other. i have checked all filters inside the machine and if you start a wash program the sprayers work and the water is splasing. please help with sugestions.


... Bosch Dishwashers

Bosch shu9925 At the start of the cycle, the washer is in pump mode. It remains that way. No water flows into the washer.. It just continues to pump. We checked the drain, some debris and checked to see how the pump was working, it is fine. Any suggestions?


Take bottom front panel off to expose the bottom tray. you will find there is water in it. mop water out and appliance will operate ok. turn off at mains first.\015\012\015\012if fault reoccurs, you have a leak which will have to be trace ... Bosch SHU9925UC Built-in Dishwasher

My Delonghi Dishwasher keeps turning off. The dishwasher is turned on at the power point. The water is turned on. Okay When I press the POWER botton on the front it wont stay on. I have to keep my finger on the POWER button and then press the START button for washer to work. If I do this it will then pump out any water in the bottom and start to work. ***BUT when you take your finger of the POWER button the washer just turns off and stops working. Do you have any idea what could be the problem p


Yes, the power button is faulty. by pressing the power button forcefully, you are in effect allowing the contacts to close. Replace it. ... Dishwashers

I have a F&P Model DD602I. I had a repairman out to change out hoses that were bad and now I have this problem: When I just run the bottom unit, it works fine, but a bunch of water ends up in the top unit that I have to drain out. If I just run the top unit, water collects in that unit causing a default. Now if I run both units together and I start the top unit about 3 seconds after starting the bottom unit, both units work fine! When I look at the hoses under the sink, they loop down quite a bi


Try to isolate the drain hose of the top drawer by disconnecting from the U hose. Run the bottom drawer. \015\012\015\012Similarly isolate bottom drawer and then run top drawer.\015\012\015\012See if problem is linked to back ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

I have a 2500 craftsman power washer with a Briggs and Stratton engine. I used it about a month ago and it worked fine. Took it out yesterday and I could not pull the rope to get it started. I took out the spark plug to release the compression but I still could not pull the rope out it is locked any advice.


It sounds like the pump is seized. Make sure any pressure has been released by pulling the trigger on the gun. Sometimes this will allow you pull the cord. If the pump is seized, a new pump would be in order. ... Briggs & Stratton Pressure Washers

I have a Kracher K 4000 GS pressure washer and it seems to have been fine until today. When I start it and squeeze the trigger there is nor pressure, water comes out but as it would normally from the hose. The engine does not even seem to be under load. I used it the other day and got pressure when I picnhed off the soap hose but that did not work this time.


... Karcher G3025OH Pressure Washer

I HAVE AN EXCELL PRESSURE WASHER-MODEL EXPRO 2530-HONDA ENGINE GX200QX2-IT HAS A CAT PUMP MODEL#2SFX30GZ1. IT IS VERY HARD TO CRANK UNLESS YOU DEPRESS THE HANDLE ON THE SPRAY WAND WHILE CRANKING.ONCE STARTED IT WORKS FINE UNTIL YOU RELEASE THE HANDLE AND THEN THE ENGINE QUITS.IT DOES NOT GO INTO BYPASS MODE.


... Caterpillar Cat Pump Pressure Washer Pump 3SP30G11

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

A feew weeks ago Smeg STA6047 dishwasher stopped in the beginning of the programme after approx. ten minutes, and gave the error code E9. There had been clearly water in the machine, but maybe not enough and the detergent box was not open. However, when technician came by two weeks after, the dishwasher worked and he said it was in order. But only after being used only once, the same problem reappeared. First the washer gave the error code E8, on the second try E9. And now it does not start at a


As you know E9 is linked to the water inlet problem. \015\012\015\012There are two scenarios here - 1) Are you using the Aqua-Stop safety system? If this is trigerring then it can shut the inlet water. The reason it can trigger is if the ... Smeg Dishwashers

GE Nautilus My dishwasher is approx. 6 years old. It has recently started having this problem. On the second cycle (the one where the little door inside opens and release the soap) does not want to work right. The door will open, but it is like there is no water spraying to spread it out. The soap (I've tried both liquid and powder) sticks and drys, running down the door and in the bottom of the tray. I have to open the machine and add the soap to the bottom of the machine if I want to get my di


Smoking from GE (Model:gsd3725f00bb) dishwasherWe moved in an old house, the dishwasher had been installed. but today we found smoking from the dishwasher and smells burned plastic. Could you have any resolution for me? or this problem is popul ... GE Nautilus 24" Built-in Dishwasher

I have a Karcher K3.91M pressure washer that pulsates when the trigger is released (off). It works fine when turned on, pressure seems OK. Before this started the unit would just turn off until I again wanted to use it. Is it a problem ? Correctable? All connections seem tight & I see no leakage.


... Karcher K 5.85 M Electric Pressure Washer

My Bosch diswasher water inlet work fine, when the wash motor or cycle need to start nothing happens. The timer is advancing normal. Water outlet(drain pump) is also working fine. There is no woosh sound (start of wash cycle) and arms is not rotating.


Hi,\015\012\015\012it sound's like the wash motor is either seized or just stuck, let's hope it's the later. Bosch had issued a service tip about this problem several years ago titled "Loosening Frozen Impellers" strange choice of word's considering ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

I HAVE A BOSCH SHU5305 DISHWASHER THAT WHEN IT IS TURNED ON IT WILL NOT DRAW WATER FOR THE WASH. IT JUST SITS THERE AND HUMS. HAD A BIT OF WATER FROM THE SINK BACK UP IN THE DISHWASHER AND SPILL OVER ONTO THE FLOOR YESTERDAY. I CLEANED THE DISHWASHER FILTER WHICH WAS COMPLETELY CLOGGED. I THINK THE DISHWASHER WORKED FINE PRIOR TO THIS INCIDENT BUT THIS COULD ALL BE COINCIDENCE. I DON'T KNOW IF I HAVE A PLUMMING PROBLEM OR A WASHER PROBLEM. THE SINK WATER WORKS FINE. I CHECKED THE ON/OFF WATER VA


If the solenoid valve is humming and calling for water, you probably have a plugged screen in the valve, some you can get to and clean, some you have to replace. ... Dishwashers

Briggs and Stratton Troy Bilt gas pressure washer one year old. I can get water thru pressure washer and bleed the air, water comes out the hose just fine until I start the pump. Then, I lose all water flow. Pump runs fine but when it's running, no water goes through.


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1589 seconds