Having problems with your Dishwashers ?

Keeps bringing C3 error code what is it the machine is a WT55DRG


Answers :

Water in the bottom tray of the casing will trip the leak sensor
this stops the cycle and engages the pump which will run until the water has gone (ie forever)
you need to dry the casing taking care not to get water onto the electrics, this will reset the switch
but you also need to find out how the water got there (leak etc.) otherwise it will reoccur
hope this helps
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Keeps bringing C3 error code what is it the machine is a WT55DRG


Water in the bottom tray of the casing will trip the leak sensorthis stops the cycle and engages the pump which will run until the water has gone (ie forever)you need to dry the casing taking care not to get water onto the electrics ... Dishwashers

IE error code, machine keeps on draining


It sounds like the flood switch in the bottom of the washer is activated. check for water in the base as the machine if maybe leaking. This is a Dishwasher? ... LG 24 in. LDS 5811 Built-in Dishwasher

Hope you can help me with my Lg ld2060wh dishwasher. I keep getting the error code te on the display panel, I understand that this is related to an issue with the thermistor, I'm not where I should be looking on the machine to locate this part or if any one can direct me to a service manual for my machine.


... LG Dishwashers

I have an LG Dishwasher model LDF9810ST. Error code E1 keeps showing (Water Leakage Problem) NO water problems anywhere to be found. I have a hard time shutting down the machine. It has had a new MAIN BOARD, and a NEW MOTOR. This unit is not 1 year old yet. Any suggestions?


Are you draining the unit in the basement or under the kitchen sink?\015\012\015\012If you are draining the unit to the floor you will need a new drain hose with a syphon breaker. This drain hose is factory installed on all new LG dishwas ... LG LDF9810ST Built-in Dishwasher

I have a Eurotech EDW154E dishwasher. I keep getting an error code 4. The previous owners said there is a way to reset the machine. Any ideas?


Eurotech Dishwashers are notorious for the E1 and E4 faults. The problem is with the solenoid they use for filling the dishwasher. The problem is something called the "Venturi Effect". The Venturi Effect is the reduction in fluid pressure that result ... EuroTech 24 in. EDW154E Built-in Dishwasher

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Hotpoint SDW80G displaying error code AL10 - machine only 6 months old so under warranty but if there is an easy fix or something external to the machine then I'd rather sort myself. Any help appreciated in deciphering AL10 error code Thanks John


... Hotpoint Dishwashers

I have an Asco D3350 dishwasher. When the cycle starts the machine fills with water and when there appears to be the right amount of water in the machine an error code F4 shows on the panel. 3 clicks can be heard during the first 5 seconds of the F4 code showing. If I cancel the cycle and start it again it pumps out the water and then fills again and the code returns. Any ideas?


... Asko 24 in. D3350 Dishwasher

Miele Coffee Machine CVA5065 CVA4066 keeps showing the error place water container in to the machine


... Miele CVA4066SS

AEG OKO_FAVORIT 6281i dishwasher - error code 20 (Siphon blocked). Out of the blue after 6 years of reliable once-a-day family use, my AEG OKO_FAVORIT 6281i dishwasher started OK but about 3 minutes into the cycle began flashing error code 20. At which point there was a litre or two of cloudy water sitting at the bottom of the machine. Since then I've tried redirecting the drain hose into a bucket, after disconnecting it from the kitchen drain. Same symptom, and no outflow except what was al


... AEG 23 in. Favorit 50750Vi Built-in Dishwasher

Electrolux EIDW6305GS1 will not run , keeps flashing error code 11 which indicates drain valve problem. I have replaced drain valve, wash pump, float valve and reed switch but no luck, still flashing error code 11


... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

My whirlpool adp 750 has error code 4, the manual says it's maybe overfilled and there may be a problem with the water inlet,but even when I reset the machine, the error stays and the machine is b


... Dishwashers

Smasungdishwasher DMT610RHS error codeCE showsup. eventhough the is not locked in, it still runs with error code CE, but the water is not coming in. but the motor is running. unless I plugged out, it keeps running. I shut off, but not responding power ONOFF.no response to any button on the control pannel. but keeps running.


... Samsung Dishwashers

I have an LG dishwasher, model LDS 5811ww. The machine fills with water, then stops filling when the error code IE comes on. I have cleaned the inlet filter and the whole inside of the tub, by taking apart the sump filter. There is good water pressure filling the tank. When I turn off the power and restart any cycle, the pump will empty the tank, then begin filling the tank again...until it is stopped by the error code IE again coming on. The other thing I notice is the water level in the tub.


Sounds like you either have a dirty or faulty water level sensor or water temp sensor. Most likely a dirty or faulty water level sensor ... Dishwashers

Our GE Dishwasher gsd4425 model has an error code of C3 - drain sensor not functioning. We have hit reset several times and this error code just keeps blinking. I believe the dishwasher was purchased in 1997. Tips on fixing?


... GE Dishwashers

On my bosch shu66 diswasher the error code indicates a number 1, aqua sensor I think. There is a screw missing in the soap dispensor and it's been letting water into the door interior. could this be repaired by replacement of the screw and drying out the interior insulation and wiring The solution I tried didn't clear the error code on the panel. Is there a reset or do I need to replace the aqua sensor or ? The machine still won't start and displays a #1 on display. There is no water in the whi


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

A feew weeks ago Smeg STA6047 dishwasher stopped in the beginning of the programme after approx. ten minutes, and gave the error code E9. There had been clearly water in the machine, but maybe not enough and the detergent box was not open. However, when technician came by two weeks after, the dishwasher worked and he said it was in order. But only after being used only once, the same problem reappeared. First the washer gave the error code E8, on the second try E9. And now it does not start at a


As you know E9 is linked to the water inlet problem. \015\012\015\012There are two scenarios here - 1) Are you using the Aqua-Stop safety system? If this is trigerring then it can shut the inlet water. The reason it can trigger is if the ... Smeg Dishwashers

Error codes PROBLEM WITH MY AQUARIUS FDW60 ERROR CODES 3 AND 5 KEEP FLASHING


Pump or heater ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have an LG LDF7811BB dishwasher. Keep getting the "LE" error code. I have replaced the entire motor/pump assemble, main PCB, and both of the other PCB's still getting the "LE" error code. Was very pleased with the performance until this. Am I missing something?


Hi,\015\012This seems to be a very common problem withe these dishwashers. The LE error code (locked engine) is not allways indicative of a motor problem. Sometimes one of the gray wires which runs the length of the door panel was pinched and b ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

Error code I keep getting an error code R02 on my Indesit DE 73 dishwasher, can anyone tell me what this means


... Indesit 24 in. DE73 Evolution Free-standing Dishwasher

Dishwasher FDB4315LFC0 Error code ER uo Second time it has happened. First time, a repairman came and said I needed a new "vent assembly", but I asked if he could "un stick it," so he took it apart and fiddled with it, and it worked for about a month. Now the error code is back, and he warned that if it came back, I should have it replaced. I've only had this NEW machine 10 months -- this shouldn't happen, right? Any suggestions? Thanks.


Who's to say what should or shouldn't happen?Sounds like you need a new vent assembly. ... Frigidaire Dishwashers

When I turn on my Turbo dishwasher it goes for about 3 mins then comes up with an E1 error; I've tried resetting the machine, but then the display shows "1h" and "05" flashing three times each. The machine starts and error code above happens again.


... Dishwashers

Error code OE; dishwasher stops with error message 2 min into cycle, drainage seems OK, water doesn't appear to pump into machine - any advice?


Hi,The most common cause of an OE error code on a modern LG dishwasher is: 1. Blocked drain hose 2. Obstruction in the sump area (beneath the filter, which needs to be removed to check for onstruction) 3. Failing drain motor.& ... LG 24 in. LD-12BW5 Free-standing Dishwasher

Leaking dishwasher leaks intermittently. I removed the side panels and there is no sign of water in the base of machine. Door seal seams to be intact. What else can I check. Seal that needs replacing? Machine is 18 months old. seams to leak on the right side of the machine. Please advise. many thanks. My dishwasher showed the error code either OE or E1, I think it was more OE. I stuck my hand in the filter in the bottom of the machine and then it was okay but the next time it was used it leake


What sort of soap powder do you use\015\012some soap powders foam a lot in machine causing dishwasher to leak through seals\015\012also check that the machine is square that is the door is closing parallel with cabinet\015\012do no ... Dishwashers

We just installed a Fisher & Paykel DD603 dishwasher. Intially it would not drain correctly. And, proceeded to flood the bottom and set off the F1 error code. I dried out the bottom to get the F1 code to stop, which it did. After adjusting the leveling the dishwasher drained both drawers correctly, once. A few minutes after the rinse cycle had finished and the drawers were empty of water the F1 code started again. Now it will not go away unless I unplug the machine. I dried out the bottom very w


HI. The original code(f1) is in reference to a overfill condition. This may be a clogged drainage Assembly. This condition will usually cause the control sector to short out if not corr ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0636 seconds