Having problems with your Dishwashers ?

I have a Whirlpool dishwasher model DU1055 and it wont start. Some led in the front panel are flashes. i asume they are a code problem. Can you help???


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Whirlpool dishwasher model DU1055 and it wont start. Some led in the front panel are flashes. i asume they are a code problem. Can you help???


... Dishwashers

We have an Asco type DW 95.5 built-in, model 1885. During operation, it stops, all the lights across front panel flash. Code F2 flashes. Although stopped, something electric still runs. When I pop the circuit breaker, all is stopped. However, when power is restored, the lights and code flash as above, and, again, something electric runs. My email: [email protected] Thanks for any help...


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Based on your description " During operation, it stops, all the lights across front panel flash. Code F2 flashes. Although stopped, something electric s ... Asko Dishwashers

My Whirlpool Quiet Partner IV has alternating flashing lights across the front panel where I make selections for the type of cycle. When these lights are flashing, the dishwasher will not operate. We have already replaced the circuit panel and the problem persists. We have shut off power at the circuit box several times with no success. Please help!


Here is the tech sheet\015\012http://www.servicematters.com/docs/w...%208530866.pdf\015\012\015\012Here is a manu ... Whirlpool Dishwashers

My dishlex dishwasher is a model 560 silent range with eco save and has a printed circuit type switch arrangement it has man code of b8833ww or 88833ww the problem is that the pause start button activates but dose not latch in I suspect that the problem is with a latching relay behind the switch panel as i have had the front off and cleaned the contcts with contact cleaner! all of the buttons work including pause ! any advise would help as would a wiring diagram and or a operation or workshop ma


Hi.The switch on this machine's control module is electronic. I do not think you will find a relay. In normal conditions the button is not supposed to stay latched If the button is defective you may get the same problem when ... Dishwashers

My dishlex dishwasher is a model 560 silent range with eco save and has a printed circuit type switch arrangement it has man code of b8833ww or 88833ww the problem is that the pause start button activates but dose not latch in I suspect that the problem is with a latching relay behind the switch panel as i have had the front off and cleaned the contcts with contact cleaner! all of the buttons work including pause ! any advise would help as would a wiring diagram and or a operation or wor


Latching relay or door lock assembly need for you to check on that model number 560 silent range wont come out on dishlex's site should be a dx followed by some numbers try also to shut off the main power for 7 minutes to the unit to reset the contro ... Dishwashers

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

I have a dishlex global 300 on which I removed the front cover a black wire came loose and I didn't know where it came from thanks to jyackle5 I have fixed that issue. The problem I have now is the eco light flashes and that's it (nothing else functions). I removed the front panel as the bottom door seal had blown and junk oosed behind the front panels I washed the junk out and cleaned the hole washer while I was at it the bottom of the washer (where the heating element is) over filled so I tipp


Easy fix, Use a bit of force and pull the dishwasher out.Get a few towels and tilt to the left. Water will drain out. Push back in. wait 10 mins and turn on.\015\012\015\012\015\012\015\012Regards ... Dishwashers

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher

Candy csd-68-80 all four lights on front panel lit, started flashing within few seconds of switching dishwasher on, no previous problems,dishwasher not overfilled, checked manual which said too much inlet water unsure what this means or how to check it. do all usual cleaning,salt,arms etc. had dishwasher about 14 months and use it every day never had any problem before


... Candy Dishwashers

Hi , I have dishwasher Frigedare #fdb 4315lfco .The control panel is flashing and before when I press the cancel button the problem disappearance but now only flashing and does not work . Please help my .


There is a most likely a faulty in the main control itself it it is not functioning. Is there power to it? You can check with VOM voltmeter. If so, it is likely faulty. You can check with a voltmeter to see if there is any power being sent out. ... Frigidaire Dishwashers

Hi , I have dishwasher Frigedare #fdb 4315lfco .The control panel is flashing and before when I press the cancel button the problem disappearance but now only flashing and does not work . Please help my .


Try unplugging it for 5-10 minutes to reset it. Someitmes the electronics just go bleep and need to be reset like you PC... This should clear it up it there are no contol panel or control board issues.. ... Frigidaire Dishwashers

Mod# mdb7601aww.... When I press cycle key, say heavy duty, then close door the 2H light flashes. I press the start button and the unit will not start. I have shut it down electricly and get the same results. what can be the problem? The front panel with the start/delay buttons or the inside control panel? I like to figure this on out the first time because each of those parts are $100+.


... Maytag Dishwashers

DD602I USA v2. Runs approximately 10 min then beeps continuously and on the front panel the middle light is red and on the inside panel the "Del" "Fast" and "Rinse" lights are red. What is this fault code indicating? I have made sure spray arm, impeller assembly, are clean and not blocked. No kinks in drain line. Induction motor sounds a bit noisy. This is only a problem with lower drawer, top drawer works fine. Thanks, Keith


... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Quick Rinse light was flashing at end of cycle. Opened and closed door and pushed Start. Quick Rinse and Cancel/Drain light are now flashing and machine won't start. Turned off power supply (30 seconds) / turned on power supply and then tried again to start the dishwasher, but same problem. Control panel seems to be frozen at the Quick Rinse/Drain mode and will not cancel. Help! Thank you


Ok try this, open the door and then hit these buttons in the following combination. HI TEMP - DRY - HI TEMP - DRY...then close door and press cancel...then wait for the pump to shut down. you should be able to run a cycle after this...If this fails ... Dishwashers

I have a GE dishwasher with front control panel and at first the wash and dry lights stayed on and it was beeping every 30 sec. when I turned the breaker off for the required 30 sec. the lights started flashing and it is still beeping. The control panel seems to be frozen as it is not working and wont do anything.. everything was working fine before this. I bought it at Home Depot on 3/14/07 and had it installed by a licened electricion. Help


Call ge @ 800-386-1215 for service ... Dishwashers

My kenmore ultra wash quiet guard deluxe is having problems. The clean light flashes and the machine will not run, this did happen once before. Unfortunately, I can not find the code that was given to me. It is a sequence of buttons to push can someone please help me?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. If the clean light flashes 7 times, pauses, and then repeats then\015\012it means the dishwasher doesn't ... Kenmore Dishwashers

I have a Baumatic BDW 45.1 slimline dishwasher, the unit will power on but I cannot select a program. I was able to place the unit in to reset mode once by holding down 'P' and power cycling the unit. This then allowed me to choose a program and complete a full wash cycle. Now I cannot repeat this steps and the unit remains with just power light on. There are no Error codes displayed at all. Could this be a problem with the front panel?


... Baumatic 18 in. BDW45.1 Built-in Dishwasher

I have a Kenmore UltraWash QuietGuard Model # 16632. Yesterday after 8+ years of problem free operations, it stopped working. When I went to unload it, the dishes were completely dry, the inside of the unit was still warm but there was about 1.5" of water in the bottom of the machine. None of the front panel light or buttons work any longer and I have verified that there is power to the unit. Help?


... Kenmore 16632 Built-in Dishwasher

My dishwasher KUDSO1FLSS6 doesn't work, green sensor next to clean indicator on the panel keeps flashing . If you can tell me what the problem is I'd be very thankfull . In case you need to contact me by phone my number is (631)672-9096 , thanx in advance for your help


... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher

Diswasher A couple of days ago my dishwasher would not start, there are lights on the front panel and it starts a washing programme but doesn't actually wash anything. I removed the filter from inside the dishwasher and it is full with water, it seems like there is a blokage somewhere. Would a blockage cause the diswasher not to start. Any help on this problem would be greatly appreciated.


Jhgf ... Whirlpool 24 in. ADP6940 Dishwasher

Kitchenaid KUDi01ilWH My Kitchenaid dishwasher has stopped responding. On the front panel, the Cancel, Rinse Only, and Hi-Temp Scrub lights aer flashing regularly and un unison. Cannot find any indication of what these error lights mean. Thanks for any help.


... KitchenAid 24 in. KUDI01IL - Multiple Color Free-Standing Dishwasher

My 1998 GE dishwasher leaks. Into the floor, now I see stains on the ceiling below. What to check? Door seal is fine. The dishes get washed. Pressure is good to go. No water out of the front of machine, seems to be coming from below. Take panel off and inspect connections? How about line from sink? Is there a site with illustrations or video repair about this specific problem out there? Any help is greatly appreciated...


Check the water connection at the valve to the dishwasher. If the dishwasher only leaks when used then the motor seal is damaged. If leak is constant the the leak is at the supply to the dishwasher from the water supply at the valve\015\012 ... Dishwashers

We have a Kitchen Aid model# KUDP02IRBS1 serial# FT1404764 The dishwasher will not work and the "Normal" light is flashing. We have had the control panel replaced once already with this similar problem and it worked for a while. Any suggestions? Thanks for you help!


... KitchenAid 24 in. KUDP02IRBS Stainless Steel Built-in Dishwasher

I have a 8 yr old model 16879 that stops apparently during the drain cycle. At this point the lights on the panel flash in what appears to be a coded sequence. Pushing the cancel button seems to try to start the motor for draining but immediately shuts off. Do I have a controller problem or something in the motor/pump area? David


Hi,It could be either...I would tear into the drain pump first and verify that nothing is stopping it from turning, then go for the controller if that seems to be okay...\015\012Dishwasher Problems - ... Kenmore 16879 Built-in Dishwasher

Just purchased new bosch (SMU 6805au) dishwasher. Starting cycle and front display panel shows E - 17 after a few minutes into cycle. THe manual is less descriptive on problems than first anticipated. Please help.


Have you turned the inlet water tap on?\015\012also check if the inlet water pressure is within the rated range in the manual.\015\012Some Bosch dishwashers will only work with hot water connection. What is the water temperature required ... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1505 seconds