Having problems with your Dishwashers ?

I have a ge triclean quiet power 1 dishwasher - I cannot reset the options. I close the latch and it hums but no water is coming in.


Answers :

It may be in a cancel drain. The humming might be your drain pump running. If you let it go through this most GE's the drain pump has to run for 2 minutes and it will then reset itself and you will be able to select the normal wash cycle. If its humming for more than 2 mins or so then you might have another issue. Make sure your shut off valve on the sink is turned on. You could also flip the breaker and kill the power to the dishwasher for about 15 mins to reset the controls. If none of this works then if you could give me the model number of the unit located inside the door usually on the left hand side. I might be able to find a tech sheet for the unit. Let me know if this helps _MJ_
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a ge triclean quiet power 1 dishwasher - I cannot reset the options. I close the latch and it hums but no water is coming in.


It may be in a cancel drain. The humming might be your drain pump running. If you let it go through this most GE's the drain pump has to run for 2 minutes and it will then reset itself and you will be able to select the normal wash cycle. If its humm ... Dishwashers

Inlet/drain light on. i know it drains OK because if i pour water into bottom and close door and turn on i can hear it draining water out. it wont fill. i have cleaned everything and taken base off and cleaned and checked float and all ok. i have tried every combination of holding buttons down and trying to reset but machine just makes low humming noise and after about 5 seconds the red light comes on again.


... Miele 24 in. G646SC Plus Free-Standing Dishwasher

My whirlpool quiet partner II is not quiet at all. When I start the cycle it starts humming and a little vibrating and I open it up and no water. I close it and wait it out every 10 minutes I open it back up and no water. The heating element is hot and stinky since there's no water. But once the wash cycle is over the rinse cycle works and theres water. What's the issue?


... Whirlpool GU2400XTP Built-in Dishwasher

Miele g892 scu plus, about 5 years old. when on, all it does is run some motor (humming sound) and flash salt or intake/drain. No program lights on. Sometimes can be reset so rinse light comes on and nothing blinks, but humming motor still runs and salt eventually blinks. I removed toekick panel; there is water in pan. I disconnect drain hose, only a little water came out. Any ideas?


... Miele G892SC SS Dishwasher

I need to know how to reset the "brain" the start button is flashing and won't stop when I close the door it makes a humming noise and no water is running. I turned off the breaker but it won't reset. Is there like a "hard reset" I can do


I don't think you may need to reset the dishwasher. All that might be happening is the float switch located in the base may be malfunctioning. It could be stuck. Try pushing it down and see if it lifts up by itself. It should only lift when water is ... GE Adora GHDA656LSS Stainless Steel Built-in Dishwasher

My hot point dishwasher is not draining,after all cylces are complete there's always 2 or 3 inches of water on the bottom of the washer, what is causing this? I have a Hotpoint dishwasher 24" built in. The switch won't come on just hums. When I oprn the door ther is 2" of water on the bottom? Any solutions . Where is the reset button on serial number hda430vww, hda400vba> Thank you!


... Dishwashers

Whirpool dishwasher Du1055xtss2 will not statrt or reset it keep draining even tho is not water in the controls don't respond,them after seconds it stop the i have to reset and once close the door the washing button comes on them stop again


... Whirlpool GU2400XTP Built-in Dishwasher

I have a Kitchenaide Whisper Quiet Ultima dishwasher. It will come on, but no water comes in. Is there a reset button or something that may be clogged?


Are you able to provide the model no. of your dishwasher please.\015\012\015\012NO water coming in could be either due to water inlet solenoid not working, the controller not working or the flood switch being triggered.\015\012 ... KitchenAid Dishwashers

I tried the steps listed at this website for the same issue I am having. http://www.fixya.com/support/t273954-kenmore_elite_dishwasher The steps worked to get the dishwasher to "reset" with all the lights coming on. The problem I am having now is that after the "reset" the dishwasher starts to run a small cycle for about 5 minutes. Upon opening the washer, nothing has happened inside (no water, no visible movement of parts, no soap container opening). Upon closing the dishwasher and trying


I think think the water fill is ok and the drain is ok as it uses a seperate drain motor . but what is not working is the main wash motor . so no water is moving and the wash arms are not going around and the lights ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a kitchenaid quiet scrub dishwasher that fails to function. When you close the door and press the start button the clean and cancel lights come on and the pump starts up. No water enters the machine and the pump keeps running.


Ther is a small impulse pump on the bottom of the unit. the diaphram gets old and it stops functioning but sometime then it leaks . so if it's not leaking , turn off water suppl and remove the fitting for incoming water some have screens right here ... KitchenAid Dishwashers

I just installed a new Kitchenaid dishwasher (Model KUDE60FVSS3). After filling with soap, closing the door and starting the machine, it fills with water, waits a couple of minutes and then I can hear low humming noices coming from down below. After opening the door it appears that neither spray arm has turned as if to wash. This dishwasher was purchased new a few years ago and kept in storage as our basement was being finished. This dishwasher has never completed one cycle. Any and all inf


If you have a garbage disposal, there is a plug in the dishwasher that has to be removed for the washer to drain. ... KitchenAid KUDE60FVSS 24 in Builtin Dishwasher

GE GSD2230 JUST RECENTLY I'VE BEEN HAVING TROUBLE GETTING IT TO START. I HAVE TO KEEP PLAYING WITH THE DIAL. IT'LL HUM BUT WON'T PULL ANY WATER. AFTER PLAYING WITH IT A WHILE IT'LL COME ON AND OPERATER CORRECTLY. I'VE NOTICED THAT WHEN IT STOPS, IT'S NOT STOPPING IN THE SPOT THAT IT USE TO. MY UNIT IS CLOSE TO FIVE YRS OLD.


... GE 24 in. GSD2230Z Built-in Dishwasher

Flashing lights My GE model # GHDA455L00CS Quiet Power a dishwasher's lights are flashing when I start it, will not reset or in-take water. I've tried unplugging it and restarting. Nothing. Tried removing door door screws and press down door latch. Still nothing. HELP!!!!!!!


... Dishwashers

Flashing lights My GE model # GHDA455L00CS Quiet Power a dishwasher's lights are flashing when I start it, will not reset or in-take water. I've tried unplugging it and restarting. Nothing. Tried removing door door screws and press down door latch. Still nothing. HELP!!!!!!! IT WILL NOT PROGRAM. IT HAS A FLASHING LIGHT. WE HAVE BOUGHT EVERYTHING BUT STILL DOES THE SAME THING


It mite be the circut board problem..just  re-soldered a few of the pins in it and things will be back in working order. ... GE Profile PDW8400J Built-in Dishwasher

Something was stuck in the latch, which made the machine not start. I removed item, however, the lights come on, the heat comes on, bot no water or the rest of the cycle begins...help.. I have held down start/cancel and the heat dry buttons. I have unplugged the power for three minutes... I have taken the front covers off, looked through the latch mechanism but found no other issues. There is a little water left in the basin, so I checked to see if there was a clog, by blowing air into th


Hi,Sorry for the delayed response. Your problem dated 30th Sep 2009 was reposted today on FixYa. I am sure by now some other expert must have responded to your question and solved your problem.If this is not the ca ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Our dishwasher seems to have stopped working over night. The power button comes on and the unit beeps to acknowledge start, but then there is only a very light hum & the unit does not start. No water comes through the unit and it just hangs at the light hum. We have not turned off any water but just checking if there is a simple solution? Adam Hdw100sst


Suspect pump.on start the pump will activate to remove condense water from drying the last load.if the pump does not start then the next step of adding water to start wash cycle will not happen.ensure pump is not blocked ... Dishwashers

Hi I have a Bosch dishwasher model SGS43T72GB/09. It has been working normally until lunchtime today and we noticed water pouring out of the door. We emptied the water and realised that the fitler was blocked with grease. We have cleaned the filter and tried to reset it. There is no water in it but all three lights are on check water, active & end when we try to reset it. If we put it onto a cylce active light comes on and you can hear it doing something but its not filling with water. Can you


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Asko D3530 water inlet fault code, water valve is on, water comes in but after water comes in for a couple of minutes we get a (inlet water fault code) check power at circulating pump no 120v unit will not run reset system it will drain and start cycle again with same result


Hello,\015\012\015\012It is common for these valves to "appear" to be ok, meaning they begin to allow water into the unit, but then one of the two coils or plungers inside fail, or are clogged with mineral deposit from the water or other ... Asko 24 in. D3530FI Built-in Dishwasher

Bosch SHX46A (6 years old) Selected regular cycle, pressed On and closed door. Cycle did not start normally. Pump runs, but no water is coming into the DW. I confirmed the water supply line is turned on. I opened door, turned off On/Off switch, then poured water into drain. Then turned On/Off switch on. DW began pumping water OUT of the DW. Also, it doesn't matter if the door is open or closed - if you turn the DW on, the pump will run. I suspect a problem with the electrical controls, or perha


From your description, I doubt that the problem is door latch is the cause.\015\012\015\012The first thing that a modern dishwasher does before it begins to fill with water is run the drain pump.  It appears that this DW is not progressing ... Bosch Integra® 500 SHX46A0 Dishwasher

Humming noise i have a GE nautilus GSD2200 model which has not been used more than 4 years that is giving me trouble.  it's making a loud humming noise (the noise comes and goes, comes and goes) which seems to be coming from the motor area at the bottom of the unit.  I stopped it in the middle of the cycle, but the water seems to be stagnant at the bottom.  any suggestion on fixing the problem myself?


I have seen this SOOOOO many times in my 35+ years in the appliance repair industry.......it is very typical....here you are this is an answer I provided someone with the exact problem not to long ago..............This is a t ... GE Nautilus 24" Built-in Dishwasher

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

I have a GE dishwasher model GLDL560N10SS. I noticed a burning smell coming from it the other day and then realized that although I can hear water running into the dishwasher when I start it, it never actually runs in the sense that the water is pushed through the various outlets to wash the dishes. I'm assuming that it is because the unit is dry and the heating element is still coming on that it is causing a burning smell. If I open the unit and reset it, it pumps the water back out into the si


The problem sounds like it is in the water inlet selonoid. Pull off the bottom panel and this is the part that the main water line hooks to there is a selonoid and it has a plugg inconnection to it unplugg it and check for power when the unit is supp ... Dishwashers

Latch problem...? When I close my dishwasher and attempt to latch the door, The latch does not appear to engage and no lights come on, and no cycle begins...? I believe the door is closed all the way, but........?


Make sure nothing is blocking the latch or the door. ... Kenmore 24 in. 16539 Built-in Dishwasher

Aeg bs45e water heater, heats water for 5 mins and then 'trip' light comes on and pressing reset button does nothing, heater must be turned off for 5 to 10 minutes b4 it will heat water again


... Dishwashers

Bosch sg14305au/12 dishwasher fills with water then just hums. the water does pump out when reset


... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1373 seconds