Having problems with your Dishwashers ?

Unable to remove screw holding impeller mod, 665.15992


Answers :

Is this the model no. of a Kenmore dishwasher?
It may be a left hand thread. Did you try that?
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Unable to remove screw holding impeller mod, 665.15992


Is this the model no. of a Kenmore dishwasher? ... Dishwashers

I have Kenmore dishwasher Model # 66517795791, and I need to remove the impeller to clean underneath the screen. When I hold the impeller and turn the screw in the center counterclockwise, it does not actually unscrew up and out.


Hi,\015\012\015\012It sounds by your description that you are going about it the correct way, but the impeller is likely spinning on the shaft, i.e. the flat spot`s on the inside of the drain impeller shaft are rounded, hence turning the ... Dishwashers

Model # 66515772990rn Water will not drain, so I tried to remove impeller but screw in mote shaft will not unscrew. While attempting the moter turns and I have no way of holding the shaft. Is there a special tool for this purpose? Also is the dishwasher worth repairing, the moter works fine?


... Kenmore 16932 Built-in Dishwasher

How do I remove the screw holding the impeller to the drain motor?


(old question but might help someone in future)How to take screw of dish washer impeller:Impeller heats up when the heater at the bottom runs... so maybe impeller melts a bit and sticks on the screw.Heat\012 up the impeller with a ... LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher

I want to remove the white plastic wheel that propels water into the circulating arms. It is held with one screw which I cannot seem to be able to loosen. This white plastic wheel has 2 small holes in the surface which are perhaps there for some special tool to hold the wheel stationary in order to loosen the screw holding this wheel in place. Underneath this gray plastic housing is the heating element. I want to remove it in order to clean accumulated deposits of gunk.


It's reverse threaded. ... LG 24 in. LDS 5811 Built-in Dishwasher

Kenmore BuiltIn Dishwasher Stock 17512 Model 17512200 Type 575-0 Serail FM3309375 Probelm: Water sprays out of lower arm weakly, and not out of upper arm at all. Action taken: Unscrewed the 4 screws holding down the item underneath the lower spray arm, and then the small item under that. Found major refuse from years gone by, removed, cleaned. Reassembled, same issue. I suspect I have to get 1 more level down, to the intake for the pump? found 2 screws to remove, but was not suc


... Dishwashers

I have a GE Dishwasher model #GSD4134Z02WW. I am trying to remove the lower spray arm. Mine is cracked. There are no screws or bolts holding the arm in the dishwasher that I can see. The new piece appears to have threads on it as to indicate that you would just screw it in place. The old piece doesn't screw/turn. How do I remove this piece?


Whack it with a block of wood and a hammer ... Dishwashers

Drain Clogged I have a Kenmore Quiet Guard Plus dish washer. The water will not drain from the unti. I believe the drian in the dish washer is pluged. I removed the 8 screws from the pump/strainer unit at the bottom of the unit I removed the top that the screws were holding donw, but can't figre out how to get to the drain to unplug it. The center metal unit is exposed and nut head is exposed. What do I do next to get to the drain hose to unplug it?


You might try pouring liquid plummer in the drain part and jet it set it shouold eat through whatever is in there ... Dishwashers

I have a Whirlpool dishwasher model #DP840DWGX2 I need to remove the filter screen, but it's either stuck or has a screw holding it down. I don't want to break the filter screen by muscling it off if it is being held in place by a screw. My owners manual does not explain how to remove this screen. Thank you


From what I can see in the service prints, it just snaps into place. I see the screen as a round screen on the bottom of the unit. If it doesn't come out fairly easily, just use an old toothbrush to scrub the crud loose. It will go through the dra ... Dishwashers

I have to remove the outer white cover from my F&P DW920 dishwasher in order to locate the nuts that hold the hasp for the door latch. I've removed all the obvious screws but don't know ho


... Dishwashers

The dishwasher started making horrendous noises. I removed the bottom panel and narrowed the noise down to the motor (the noise starts and stops when the motor kicks on and off). How do I remove the motor to visually check it out? I thought I had all of the screws removed, but it feels like something is still holding it in place. thanks My model number is GSD4060N10SS (GE Dishwasher)


... General Electric GSD4060NSS Built-in Dishwasher

JENN-AIR Model number JD3B10AWX. Bottom of dishwasher is dirty, I want to clean it. I have removed six screws holding plate down, but cannot find any way to remove spinning blade. I think there's a filter underneath that I can clean or replace. Questions: 1. How to remove spinning blade? 2. Am I going about this correctly. Thank you


We have been having issues with our model where there is dirty sand deposited inside of glasses and dishes.You need a torque wrench for a triple square torque screw ... Jenn-Air Dishwashers

Dishlex Global Unable to remove heater element retaining screw


I have a simialar problem with the Dishlex 450 Global model, after searching for the heating element on line, I found a picture of the element (450 model), showing that the Stainless Steel screw is actually spot welded to the element bracket, hence y ... Electrolux 18 in. ESL4114 Slim-Line Built-in Dishwasher

How do you remove the M120 part to gain access to motor and pump? Cannot remove the screw holding in the M130 wheel in place?


... LG LDF6810ST Stainless Steel Built-in Dishwasher

How do you remove the impeller from the main pump on a Hobart C44AW. I have taken the nut off the end of the shaft but I don't know if the impeller pulls off or screws off.


It pulls off. Just use a small/medium sized gear puller and it'll come easily ( there is a lip on the impeller for the purpose of pulling). ... Hobart 40 in. AM14-254 Free-standing Dishwasher

I have an electric karcher pressure washer. Motor not working and I need to check the wiring inside. What tool do I need to remove the screws holding the top and botton cases. Screw drivers wont work.


... Pressure Washers

I have a Bosch Dishwasher SHU3302UC/14 that will not drain. We initially thought the problem was the disposal because water kept backing up into the sink. We replaced the disposal, removed the dishwasher plug in the disposal, but the dishwasher still does not drain. I would like to check the drain line, but am unable to access it. I removed the kick plate and the screws that secure the dishwasher to the underside of the counter, but the dishwasher will not move. Can you access the drain li


... Bosch Dishwashers

GE model GSC 3407 POOWW How is the lower spay arm assy removed? I want to clean the sump parts. By the way, the impeller was in the bottom of the sump, but I was able to fish it out.Is it a problem to screw the impeller back on the shaft so it will not come off again? Thanks for any assistanc you can provide. Doug Smart


... GE Dishwashers

How do I access the soap dispenser grommet on a Whirlpool DU920QWDB3 Quiet Wash Plus? I removed the 8 hex screws holding the plastic inside panel, but the panel seems to be still connected near the top underneath. What is still holding it on and what do I need to do to release it?


The vent grill has to be removed to release it. The diagram is here: ... Whirlpool Dishwashers

Kenmore ultra wash #15765 will not drain. purchased 1996, web says no such model exist, but i have the manual, and it does, i need help . I have taken out the lower sprayer arm and the spinner that chops up the food left, even removed about 10 screws that hold down what looks like a filler but it did not allow me to remove it. How do i access the drain to see if it is stopped up. Do i need to pull it out from the counter and go from the drain hose,or somehow go in from the bottom??


... Kenmore Dishwashers

How do you remove the lower spray arm on a Kenmore Ultra Wash (665.17019.402)? I was told to hold on to the plastic screw and spin the arm counterclockwise to remove, but I've been spinning and spinning, at leat 100 rotations, and it is not coming off. I've uploaded pics so you can see the apparatus. http://picasaweb.google.com/gregoryor/Dishwasher?feat=directlink


Hi, In the center of the spray arm is a threaded piece of plastic/bolt.\015\012Use pliers and turn that tab on the bolt. If it doesn't turn easy. Holt the bolt and try to turn the spray arm with you hand.\015\012It will release the spray ... Dishwashers

Drain Clogged Drain is clogged. Have standing water. I removed the 6 screws holding the top part of the strainer/drain motor on the bottom, but can't figure out what to do next to get to the drain to remove the clog


The strainer should have trapped all the big particles. Are you sure the drain is clogged? More than likely the evac. pump is shot. ... Kenmore 24 in. 17602 / 17604 / 17609 Built-in Dishwasher

I am trying to clear the drain on my ge portable dishwasher. I have removed the 2 screws for the drain cover but my dishwasher has another part on top attached to the spray arm that is holding my cover on . I can not figure out how to remove this part. the model # is gsc5511pooww


... GE Dishwashers

Dishwasher will not start upon lowering the door. appears to have some kind of magnetic sensor on the door that is cracked and falling off the door. Unable to tichten the screws holding this sensor


"Universal Duct tape". Apparently, one needs to be channeled through a Hobart distributor.Am still checking that out to see whether they will ship me the inexpensive part (Guess <$20)or whether it will be necessary to have a Hob ... Hobart 24 in. LXIH-3 Built-in Dishwasher

I'm trying to take apart a kitchenaid dishwasher door model KUDP01ILWH0 to replace the dispenser assembly. I removed all the torx screws holding the outer and inner door panels together, but they don't want to separate. Anyone know what the trick is here? Thanks


You can get assembly diagrams of your system. Go to;\015\012http://www.appliancepartspros.com/partsearch/model.aspx?model_id=503 ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0719 seconds