Having problems with your Dishwashers ?

Kleenmaid DW8 top washer does not operate. Apparent blockage in the water supply tube which runs up from the bottom water supply. How do I remove the bottom assembly comprising the main filter, waste trap and micro filter? I appears that these must be removed to access the water supply tube mentioned above.


Answers :

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kleenmaid DW8 top washer does not operate. Apparent blockage in the water supply tube which runs up from the bottom water supply. How do I remove the bottom assembly comprising the main filter, waste trap and micro filter? I appears that these must be removed to access the water supply tube mentioned above.


... Dishwashers

Frigidaire Dishwasher model # FDB520RHB2 Stopped prematurely last night while on light cycle, now will not respond at all. Noticed water at bottom of tub; tried draining manually through drain tube, removed lower arm, glass trap, and filter, and water remains; tried electronic reset by switching off breaker for several minutes; all to no avail. Electronic controls (cycle/option select) will not respond at all.


This is not a uncommon problem and it sometime's is the pc control panel but i find that it is more often the interlock ( latch assembly .) i would change // there has been a improvment and i belive this will solv ... Dishwashers

My Bosch dishwasaher model SGS53 has stopped working and has water in the bottom of it , i have cleared this and checked the small impeller for blockages - this is ok. i have also checked the water inlet filters and the drain tube is clear . I have the top and left sid panel of and when i lift the red rod it allows watrer to come in but stops if i release the rod thr lever in the base of the machine int which the red rod fits appears th be at its lowse level and therefore the red rod cannot be p


... Dishwashers

I have a Kitchen Aid KUDS03CTSS3 dishwasher. Dirty water is staying at the bottom and nothing comes out the drain hose during the entire cycle. The drain hose is looped above the kitchen P-trap, although for a time it wasn't. I use a wet vac to get the water out but there is still water below the fine filter. I thought if I could get the fine filter off, I could clean out the bottom as I think that it's full of crud down there that may be blocking things. I can't figure out how to get the l


Hi,Thanks for the follow up. I am glad it worked out for you. If I can Help in the future let me know. http://www.fixya.com/support/c64627-kitchen_aid ... KitchenAid 24 in. KUDP02FR Built-in Dishwasher

I have a Miele 590G dishwasher. Everything appears to work except for water supply. Any suggestions about what I could do or what could be broken? I opened the supply connection (the small gray box) and checked the filter - all seems good. But still - no water supply! Thanks in advance. Ross


You must to check also the tap of water which connect water to this small box may the water pressur out from tap is weak .\015\012you can use a small pan to help this test.\015\012 thanks ross ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher

I have a LG Dishwasher LD 14AW3 it fills and runs for about 30 min. It then appears that when it tries to rinse it cannot get water and flashes "1E". I disconnected the unit and when I moved it out of its position water was leaking from the bottom of the unit. after cleaning out the inside filter & the hard water filter I re-connected and found it worked. I ran a dishwasher cleaner through it at high temp. After a few loads the problem has come back. It is now located in MY garage waiting for me


Found a leaking component that was causing the foam float located and attached to the inlet valve to shut down the water inlet and the water inlet Solenoid was also sticking. I found out this simply by tapping it while it was trying to get water for ... LG Dishwashers

Hi! My bosch SHE43 built in dishwasher is about 2.5 yrs old, dishes aren't getting clean anymore. We have *really* hard water so I use the max rinse agent, but doesn't help. I clean the little canister filter with each wash, and just washed off that grate in the bottom. I also just cleaned the trap under the sink, but it didn't look bad at all. The problem is a grit left on glasses and things just not getting all the way clean. When I remove the grate at the bottom, there's a bit of water


Hello. Let's begin by tossing two cups of vinegar into the empty dishwasher and running it on it's hottest and longest cycle. Always run the hot water in the sink faucet until it is as hot as it gets before starting up the machine. Let that cycle ... Bosch SHE43C02UC Dishwasher

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Asko 1996 appears "dead".....no lights flashing, won't respond to repeatedly pushing on/off button. Some water left in the bottom...siphoned it out, cleaned filters, no blockage there. Almost like it's not getting electricity, but breaker is on. Noticed this when I went to empty clean dishes, and noticed that detergent hadn't dissolved and dishes weren't clean and about a gallon of water was still in the bottom.....


Don't know if this will help, but my dishwasher has a "propeller" device above the top and bottom racks that spins while dispensing the water. If the dishes on either rack are stacked too high (i.e. if even one plate comes in contact with that ... Asko D1996SS Built-in Dishwasher

Machine just started leaving dirty water in bottom of machine. cleaned filters,had machine apart,removed and cleaned waste pipe. pump runs and impeller feels ok.only time i could get any water to drain into bucket was when shook waste pipe very hard?


Check that the pump is clean and not loose. Make sure pump, impeller, and waste pipe are in alignment with each other and are clean. If it works when you shake the pipe, then there is still a clog inside or the pipes aren't aligned correctly and some ... Dishwashers

The check water supply indicator is alight. I have checked the incoming supply and this is ok, the filter is not blocked. If I try to run the dishwasher I just end up with water at the bottom of the machine and the programm will not progress any farther.


My phone has frized and i forgot the pasword ... Neff 24 in. S5555X0GB Built-in Dishwasher

I have model DU810SWPU3 Whirlpool dishwasher that is 1 yr old. Plastic dishes appear to have a film on them when cycle is complete. The water also seems to drain slowly. I assume that what appears to be the filter needs to cleaned but I'm not sure how to remove it to clean it. Is the plastic area with all of the square holes on the bottom of the appliance the filter? That part is what seems to be clogged. Thanks!


The problem is hard water. There is a new product out called the dishwasher filtration system. It filters the water before it enters your dishwasher. It works amazing and has a money back guarantee. You will love the ... Tappan 18 in. MDR251RE Built-in Dishwasher

After running our dishes through a wash cycle we noticed there was still a lot of food stuck on the plates & glasses etc. We cleaned out the trap but due to the murky water in the well, we also pulled out the racks & removed the bottom plate. The underside was greasy and had a lot of grim stuck to it as well as the bottom of the drawer itself. We washed the filter trap, swing arm and plate in the sink. We loaded it with the dishes that previously did not come clean and ran a full cycle. The


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have error E:15 with a flashing water tap sign - I've tried the following: a) Clean filter at the bottom - now flushes out with b) remove power - return power c) remove and clean fiter for incoming water at a sort of valve Nothing! when I attach power it continues to flush out (even without water) if I put water in it evacuates without problems. The tap does supply water I've check and with more than sufficent flow and pressure! ...Help .....Thanks Gary


Hello Gary,\015\012\015\012You didn't specify the brand or model number of the dishwasher, but I suspect it's a Bosch, in which case the E:15 error with the flashing tap sign and the drain pump running continuously means the anti-flood pr ... Dishwashers

Check water light stays on rendering machine unuasable.checked water supply.all filters .googled problem told me to switch water supply on and off rectified problem for 10 minutes then check water light came back on. water remains in bottom of appliance.


... Bosch Dishwashers

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

My chef classic dishwasher is not completely cleaning the dishes. There is no obstruction to the tablet/powder door opening, although there is a small amount of powder left at the end of the cycle. Both top & bottom spray bars are clear & rotate, the water is heating & there appears to be plenty of water getting water into the machine. Drain filters are also clear.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Magic Chef CDB6100 Built-in Dishwasher

Hi I went to put my Bosch dishwasher on this morning only to find that it would not come on . there was water in the bottom of the dishwasher so i cleaned all the water out and cleaned all the filters but my dishwasher would still not work it was only when i went t o disconnect the dishwasher from the water supply did it come on Can you please let me know what problem i have with my dishwasher and is it likely to happen again


Hello,\015\012\015\012This video will help you fix your ouch dishwasher.\015\012\015\012 ... Bosch Dishwashers

Sandy glasses The dishes on the top rack come out with a sandy residue on them....we have tried running it with the jet dry dishwasher cleaner, the vinigar and baking soda...have taken apart and checked all filters and water supply...no help with any of that. I also wonder how much water should be in there when it is running...shouldn't it cover the heating coil in the bottom? My water level is just below the coil.


A simple cleaning with any form of citric acid(tang0 on a regular basis(depending on how hard water is) will cure this "proublem"\015\012\015\012Cleans the internal filter and breaks up hard water residue(calcium) ... Whirlpool GU2400XTP Built-in Dishwasher

Kitchenaid dishwasher - small pieces of food are left on otherwise clean dishes. Water level comes to about 1 inch below heater coil. I ran it without dishes (or soap) and added about a quart of water so that level came to about 1/4 inch below heater and that's when I noticed food pieces on drain surfaces (nylon filter under bottom spray arm unit and circular plastic "trap" surrounding it). Spray arms holes are clear and water is hot.


It sounds as if you figured the solution out. The holes in the spray arm(s) get plugged by small debris, (tooth picks, seeds, bits of plastic like candy wrappers, etc) and the water does not reach the dishes to wash and rinse effective ... Dishwashers

I have an LG ldf7811st dishwasher. My bottom arm spins with water, my middle arm does not spin but does have water coming out, and my top arm doesn't spin or have water. I have just finished taking apart the arms, the supply to the upper arms, the filters and the impeller. I cleaned everything and nothing really seemed clogged. I have tested it since and it still has the same problem. I know that they aren't spinning because i placed them in a certain position before i ran the test run. They


I'm thinking like you're thinking, that it's something affecting the water pressure, but you've done everything in the upper section, so the problem must be from below, unless you have a leak somewhere you haven't noticed and are losing pressure beca ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

No water going in dishwasher, have checked water supply and small filter at the back of machine. water coming from bottom of the machine


This happened to a GE machine of mine once, and the problem was a stuck float..Inside the dishwasher tub, in the front-left corner under the silverware tray, there's a float that keeps the dishwasher from overfilling. If this is stuck in the " ... Bosch Dishwashers

Hi my dishwasher keeps tripping the electrics. it's always the same place in the cycle. there doesn't appear to be anything blocking the filter. there's always water in the bottom after a trip and the water is hot. please help


Hello there, If this unit is tripping the breaker lets say on the pump out drain cycle, then you for sure have a problem in the motor and pump assembly.Anytime a breaker trips, if the breaker isn't worn out, it indicates that it is drawing more amps ... Dishwashers

I have a Whirlpool DU810SWLQ0 that will not drain. I've pulled the unit out, snaked the drain tube, pulled the motor/pump, and pipe assemblies, and cleaned the food trap, which I also removed. I've run the dishwasher with a bit of bleach, and the water will pump in, get processed by the agitator, and be heated. When the rinse cycle comes, dishes get covered in food, and are never clean. Waste water was being used for a clean rinse. I've run the dishwasher with the drain dangling in a bucket,


Refer the wash system assembly dwg. Check if the ball (item 21) is sitting correctly. If it is out of ali ... Dishwashers

My miele G665 SC is not draining all the waste water away at the end of the cycle, i've taken the filter part out of the bottom and it's all clear and even run a cycle without it, is there another filter that i haven't found? Does anyone have a solution for this problem? Thanks James


Check for any kinked hoses and check the drain spigot under the sink where the drain hose connects into the u bend. Usually this is where food gets trapped due to the spigot not being drilled out large enough. This then causes a blockage. Also ... Miele 24 in. G665 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1805 seconds