Having problems with your Dishwashers ?

LEAKING FROM HEATING ELEMENT - Dishwashers


Answers :

Try to screw the nut, check the gasket(seal) or replace the heatimg element whit similar new one (if it is possible whit an original- that wil resist much longher) when you posting a help request please post more detail for an exacly recomandation!
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Small Burn spots on interior tub below heating element. These spots have small cracks in center of them, and leak right through the bottom of the tub, dripping water all over under the dishwasher. Nothing has falling into the bottom of the tub, and nothing has touched the heating element. What in the world could be causing this to happen? Kenmore Ultra Wash Quiet Guard 4 Mod.# 665.1603* Purchased new from Sears 2006


Hi,\015\012\015\012The heat from the element when the dishwasher is in the "drying" mode has caused the bottom to stress crack and become open so it leaks...\015\012Ultimately this will cause you to have to replace the dishwasher... ... Kenmore Dishwashers

I have a six year old dishwasher that started leaking water out of where the heating element is attached on the lower part of the unit. It appears as though the heating element has melted through the plastic. Is this a flaw in the design and is there a recall on this?


Dont use it!!!!!!!! ring the manufacturer with the serial number ect phone number should be on appliance booklet or get it from a dealer ... Dishwashers

My frididaire dishwasher is leaking at the heating element/burner (red wire). I have tried to tighten the connection from under the dishwasher but it continues to leak (very slowly). The clasp used to tighten the element does not hold it's tightness and will become too loose if tightened all the way. What do I do?


Replace the heater element. ... Dishwashers

I have a leak coming from my dishwasher from what what I think is the plastic melting from the heating element. The plastic is weakened and a very small hairline crack has formed. Any suggestions on how to resolve. The dishwasher is just over 5 years old.


... Kenmore 24 in. 17362 / 17364 / 17369 Built-in Dishwasher

The dishwasher is leaking water from were the heating element goes through the bottom of the dishwasher


The heater element got 2 screw legs that if it is a metal lock then they get rusty you need to replace the lockers for the heater legs and its not coast much what is your model # ? I get you the parts number so you can order them and do it yourself.. ... Whirlpool Dishwashers

Water leak THE WATER LEAKS WHERE THE HEATING ELEMENT GOES THROUGH THE BOTTOM OF THE DISHWASHER


TIGHTENED NUT ON UNDERSIDE OF DISHWASHER WHERE THE HEATING ELEMENT GOES THROUGH. ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

LEAKING FROM HEATING ELEMENT - Dishwashers


Try to screw the nut, check the gasket(seal) or replace the heatimg element whit similar new one (if it is possible whit an original- that wil resist much longher) when you posting a help request please post more detail for an exacly recomandation! ... Dishwashers

I have a whirlpool dishwasher DU915WKSO: when I turn the dishwasher on, the heating element comes on but no water comes into the unit. I recently replaced the garbage disposal and th dishwasher worked fine for a time or two. Since then I have only been able to get water in it once. Like I said, the heating element works but no water in the dishwasher. Thanks for any help.


... Whirlpool DU1055XTS Built-in Dishwasher

Heating element broken, water leaking


You have to pull out dishwasher to replace the element.The element is easy to replace once you have pulled dishwasher out.This enables you to reach the area that you need to reach.It is common for a element to brake.On a newer dishwasher ,I would say ... Kenmore 24 in. 15953 Built-in Dishwasher

My plastic tub on my Whirlpool GU2500XTPSO dishwasher seems to have a small dimple in the plastic below the heating element. It looks like a metal utensil or something may have fallen and was leaning


... Whirlpool Dishwashers

Kenmore Dishwasher Model 665.15912001 Heating element doesn't seem to be heating. Wash cycles are loooooong and the drying cycle doesn't exist. Easy fix or buy a new dishwasher? I haven't tested anything yet. Should I start with the thermostat or the element itself?


Hi. i would test the element first. this will be the likely issue.First, open the doorand look into the tub and locate the heating element (if it is covered, remove the lower dish rack and cover). The heating element has two termina ... Dishwashers

My dishwasher does not do a hot wash. Why is this? If I need to replace the heating element, how do i gain access to heating element on my Bosch classixx dishwasher?


Hi, a common problem with these machines is the solder coming away from the heater relay. A simple repair if your lucky. Run a continuity test on the element with a multimeter before replacing it, as it is a massive job to change it. I just changed m ... Bosch SHU9950 Dishwasher

I have a GE Profile Dishwasher, Model# PDW7880J03SS that doesnt dry the dishes. I pulled out the dishwasher and checked the heating element for continuity with my ohm meter and got a closed circuit reading. I tested the voltage going to the heating element and got a 124V reading. However the dishes are still soaking wet after the drying cycle. What am i missing, what else could be wrong with the machine that the dishes won't dry at all?


Hi\015\012\015\012Check if the dishwasher is draining and filling properly is water temperature. Water temperature should be between 120 and 140 F. If water is not hot enough then heating element has gone bad, to check the element you'll ... Dishwashers

I have an Indesit IDL500 dishwasher. It had stopped heating the water up, it looked as if it had short circuited and so i replaced it, i have power going to the element. A couple of forums state that it may be the pcb behind the timer/selector switch. Does this pcb control the program selection and heating of the element? or is there a thermostat that controls the stop and start of the heating element? Any help would be greatly appreciated


Hi\015\012\015\012The unit\015\012has two thermostats and you can test both of them for continuity before\015\012replacing, no continuity replace the thermostat. Hope\015\012this helps...please post back fo ... Indesit 24 in. IDL500 Built-In Dishwasher

Maytag MDBH970AWS Heating element won't turn off. Dishwasher heating element won't turn off. Have to shut off the breaker to make it cool down. Heating element gets hot as soon as you flip the breaker back on


The heater relay is located on the control board, a faulty relay or a faulty control board would cause the problem you have described. The fix is to replace the control board. Parts for your unit should be available from most appliance parts retail ... Maytag 24 in. MDBH970AWS Built-in Dishwasher

Dishwasher zdt 6053 Heating element not working......sometimes!!!! tried all three cicles nothing, heating element not working then its fine again for a couple of washes ????? anyone ever come across this problem, faulty thermostat ,faulty heating element,gremlin in the circuit board?????


... Zanussi 23 in. ZDT6252 Built-in Dishwasher

Westinghouse Dishwasher Model SB907W5*08 the dishes are not getting cleaned & it appears that it is not heating as i bought a bottle of dishwasher cleaner & the dishwasher is supposed to heat up enough to dissolve the lid off the cleaner to let the fluid out. after putting the cleaner through a cycle the cleaner lid was still there. i think this must mean that the heating element is broken? this is out of warranty & can't remember how much it cost us so don't know whether better off gettin


Hi\015\012If you are observing that the dishes are not clean, then you'll need to follow certain steps to be sure where exactly the issue. First thing to check for is the detergent cup and spray arms. Check if the dishwasher's spray arms are w ... Westinghouse 24 in. MDP531 RF Free-standing Dishwasher

Nasty dishwasher there is nasty wet grunge at the bottom of the door, around the place the heating unit in the bottom of the dishwasher. half the time the dishes are clean in the bottom of the dishwasher. half the heating element is melted..for some reason...what do i do. the dishwasher still works, if we make sure the dishes are clean before they go in. using more for a sanitation thing than a dishwasher. can ya'll help me?


Sounds like your heating element is broken and you should replace it to prevent a possible fire hazard. \015\012You can replace the element easily for not alot of cash. You'll need to pick up a new one at an appliance parts store, just bring them the ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

HEATING ELEMENT IT SEEMS THAT THE HEATING ELEMENT IS NOT HEATING. THIS CAUSES THE DISHWASHER TO RUN LONGER AND THE DISHES ARE NOT CLEANING PROPERLY. I WAS WONDERING HOW TO TROUBLE-SHOOT AND FIX THIS PROBLEM.


Hi\015\012\015\012follow the manual:\015\012http://www.kitchenaid.com/assets/pdfs/product/ZUSECARE/8574093.pdf\015\012\015\012if it dosent work then as you mentioned the heating unit is bad\015\012you can replace it by yourself by buying it and insal ... KitchenAid 24 in. KUDI01IL - Multiple Color Free-Standing Dishwasher

My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.


... Dishwashers

The heating element stopped heating in my Maytag dishwasher, Model DWU8860BAE. I put in a new heating element, but it doesn't heat.rnWhat might be the problem? What should I do?


... Maytag Dishwashers

Smeg Dishwasher DWD 63.1 SS, not heating; I have Smeg dishwasher that is sticking in its cycle (wash phase), water was cold, so I assumed the element had failed (or tank termostat), so I have replaced both element and tank thermostat in turn. No change, water still cold and dishwasher sticks in the wash cycle. Any ideas? (Note, no diagnostic leds on this model)


... Dishwashers

I have a dishwasher model 66516979200 it doesnt dry the dishes i saw the heat sensing light on an opened it and felt the heating element and it was not hot at all ive checked the water temp at the sink and it is at 120 could the heating element be the problen or something else


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Bosch dishwasher shx46b02uc has stopped drying. Per online comments, they seem to point to either a corroded wire or a bad heating element. We've replaced the heating element and all the wires looks fine. All other functions work - just not the heat. Open to suggestions.


Hello,Welcome to FixYa.Based on your description ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Dishwasher is model DWD1SSE type11045 Initially the dishwasher leaked water on the floor On investigation the bottom tray under the dishwasher was wet The motor was wet Tested the motor which was fine although the capacitor on the motor impellor was dead. Replaced capacitor, now no water going around the spray heads so found the impellor inside broken. Replaced that. No hoses are leaking. Machine now works fine heats up etc etc but over fills and the E5 fault shows


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1279 seconds