Having problems with your Dishwashers ?

Dish washer no power up and not sure about the board behind the control buttons, How does one go about testing it or ??


Answers :

Go to bottom off unit and see if the black and white wire is burnt . make sure the power is off
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dish washer no power up and not sure about the board behind the control buttons, How does one go about testing it or ??


Go to bottom off unit and see if the black and white wire is burnt . make sure the power is off ... Dishwashers

My 2008 frigidaire 24" dishwasher model #FDB1050REC is not washing during the cycle. I have run the test cycle and the tub is filling up and draining but no washing is taking place during the wash cycle. The dishwasher has an electronic control board and therfore no mechanical timer. I put test leads to check for voltage on the power leads to the main washing pump, which I have already replaced with a new one, and I'm only registering a low voltage of around 10 or 11 VAC. With the cycle off I'm


If you have replace the motor and this did not fix your problem then yes replace the control board ... Dishwashers

The power light is on but I cannot get any of the buttons to work at all - no lights on. One day worked and the next nothing! Does that mean the control board has gone in which case not worth repairing?


... Stoves 23 in. Q60DW Built-in Dishwasher

KitchenAid KUDC25CH Dishwasher Just installed a new control board, last week after some lengthy emails we decided it was probably the control board , control board in now in, as far as I know the dishwasher cycles thru all three of the small lite rinse buttons ad it may have finished completely, there wasno water in the bottom of the washer so all was pumped out and the dishs were dry......the large rinse button on the panel is blinking. I open and close the door but the light contiues to blink


The system does not allow me to view what other consultants have suggested to you about the problem with your dishwasher.\015\012\015\012Before you try anything else, get a Finish dishwasher cleaner kit from the supermarket and run the di ... Dishwashers

Dish washer 665.13592K600. Will not start. When door is closed you can hear the click of the latch then a relay on the control board. All buttons work except delay and start. You can push the cancel and drain button and the pump will activate. The start and delay buttons have no effect. Not sure if I have a control board or panel problem.


... Kenmore 13599 / 13594 / 13592 Built-in Dishwasher

Zanussi Dishwasher ZDT6053. Holding the On/Off button causes the indicator lights to work correctly, but as soon as you remove your finger from the spring loaded button, all the lights go off. Would guess that on/off button should electronically latch via the control board. Have removed mains power for 60 secs in the hope of a 'hard' reset, but no fix. Is there anything obvious to check or fix or must it be a replacement control board?


... Zanussi 23 in. ZDi6053SX Built-in Dishwasher

Replaced control board on my Kenmore dishwaser 665.13122k703. Still have problem with blinking lights and maybe one minute of operation, then stops and normal wash light blinking again. Cancle drain button only one that works, then normal wash blinks. I have another control board, however before I install it, should I be looking eleswhere the the problem ?


... Dishwashers

I have a Maytag MDB5601AWB dishwasher. all the switches except the heated dry switch are not working. I did the unlock thing and still nothing . Do I need to replace the switch panel or is there something I should try? I tested for power and have 120 volts coming into the circut board and through the door switch Comments: Aug 22, 2009 - I tested the door swich and I have power on both poles when it is closed. there is 2 switches on the latch but the one with power to it powers up the circ


... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Continuous alarm after a power failure an alarm started going off in the door of the dishwasher. the push button panel is not functioning. I opened the door panel and found an electronic control circuit board. It is this board that is making the noise. I unplugged the black and white pair of wires on the lower right side of the board and the noise stopped. this must supply power to board. Anyone know what this problem is?


I posted this under "Ben's" problem as well, but I had the exact same problem. I know which black and white wires you're talking about. I don't know what causes this, but getting new parts did fix it. The black box that all those wires go into on ... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

No power to washer control board. When power comes


1)check any loose connection with neutal/phase wire.\015\0122)check incoming fuse. ... Bosch Dishwashers

I have a Kitchenaid Dishwasher M/N KUDS25SHWHO. Had to replace the control board because the unit would not start. Installed the new board and the unit now operates, but not correctly. Once in awhile on the Normal cycle, it will get a third of the way through the cycle and just stop. Used to be, you could hit any of the Wash Selection buttons and than any of the Options butons and then hit the Start button to begin the cycle. Now, as soon as you hit one of the Wash Selection buttons, the un


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

We have a kitchen aid dishwasher model # kudso1msso -- quit working and the control panel button lights are out so i assume there is no power to control panel. we have power at the plug every else looks ok. . could the internal fuse at the control panel be blown or the circuit board blown.


Sounds to me like a 'breaker' must be thrown; ... KitchenAid Dishwashers

The buttons on my control panel no longer work. At first, it was just one button, then two. Now none of the buttons work. The model is a Whirlpool Quiet Wash Plus #DU920PFGQ2. Do I just replace the control panel? The dishwasher is receiving power.


... Whirlpool Dishwashers

LG Dishwasher (LDF6920ST) control panel is not working on any other cycle but the delicate cycle. Following power up only one button will light up/can be selected. It started with the normal cycle button going out then the power scrub went out along with the upper rank and rinse only.


... LG Dishwashers

I have a KitchenAid Whisper Quiet Dishwasher. Has been working fine. Circuit breaker seem to be working but control board is now not lighting up and buttons do not respond. Seems like no power to control board.


I may have leaked water into the mother board ciruitry. This can happen when there is a tiny leak or when steam gets in. Check with kitchenaid, that is a good product and kitchen aid will stand by thier equipment. ... KitchenAid Dishwashers

I have a hobart LX18C. I purchased a new control board and as I found out its factory set to the h model. How do I change the board over to the c model. How do I program the machine for the different wash cycle times, I have one that is working but its on the 140s. cycle and only heats the water to 80 degrees. I see the push buttons on the control and wonder what they are for.


Here is a Hobart link that may help. https://feg.hobartcorp.com/resourcecenter/ProductDocumentation/F18615%20Rev%20I.PDF ... Hobart 24 in. LXIH-3 Built-in Dishwasher

Model mdb7601awb diswasher . Nothing works , no buttons torn on or work when pushed, no action. 1.Have checked power to unit and is ok 2.checked door switches (2) and both work properly. 3. no visual discoloration on circuit board. There is a blue dot on the wiring harness from control board to button panel.When evaluating with magnifing glass I believe this to be blue ink droplet and not any burnning of harness. Need a Guru.


I have had the board replaced 5 times and the entire dishwasher replaced once. It was necessary to go to the state attorney general to get Maytag to extend the warranty. Just called the service center for the sixth time, after this the warranty will ... Maytag 24 in. MDB7601AWS Stainless Steel Built-in Dishwasher

I have a MDB6759AWS3 that is one year and two months old. This morning I went to the control panel to press the buttons and some would light up and others would not. I disassembled the inner panel and looked at the "computer like" flat ribbon that connects the control panel to the main circuit board and noticed that some of the wires in the flat ribbon had deteriorated. I put it back together and pressed the buttons and they flash very dimly for a few seconds and got the dishwasher working bu


You may want to check the warranty iif it is a maytag or whirlpool, some have a 5 year warranty on the control and board. If not you can go to www.searspartsdirect.com to l ... Dishwashers

I have a Maytag dishwasher MDBM601AWW. The control lock on the control pad will not unlock. I replaced the electronic control board and it worked for one wash. Control lock engaged again. I shut down the power and pressed the control lock for 3 seconds as directed by the owners manual. No luck. Please help Rich.


You have to power the unit back up and then holld the lock in for three seconds, if ths does not reset it then the console not the control bord needs to be replaced it comes with a new touch pad ... Dishwashers

I have a Whirlpool Gold Model GU2700XTSBO its only 4 years old. About two weeks ago i noticed that the green lights were flashing and it would not run, I unpluged it for an hour and pluged it back in and the lights went away and it worked ok for the last two weeks. Last night I went to use it and there is no power at all to the washer, I checked the power source to the outlet and there is power there, so I dont know if there is a reset button or some control panel problem?


... Whirlpool GU2700XTSB / GU2700XTSQ / GU2700XTST Built-in Dishwasher

No Power Hey everyone, I have power at the wall, but no power at the dishwasher. the garbage disposal is on the same circuit and it is working. I pulled the fuse behind the control panel after cussing several times seeing that I broke the ribbon cable for the buttons in the process. I do not know how to visually tell if the fuse is blown. Thanks,


If it is a Kitchenaid KUDS25 series, there is a thermal fuse located on the upper portion of the electronic control panel. You will need a continuity meter to test it with the power OFF. In addition, check that the door latch switch closes properly ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

I have an Asko 1585 dishwasher. It drops the inlet valve on step (step 12), and the recirculation pump (next step) tries to pump with no water. Later at about step 47, the inlet valve begins to work again and the dishwasher finishes the cycle without a problem. I have had the board checked, and all of the power supply and transfer circuits are good. That leaves the processor. Is there any combination of buttons to press which can completely reset the controller board?


... Asko 24 in. 1585 Built-in Dishwasher

Our craftsmen electric pressure washer stopped working while in use. We have power - red light on gfci and we tested the master switch - has power too. So what can be the problem? One post mentioned a jammed pump switch. What is that and where is it? We used it 2 weeks ago and it worked fine.


The pump switch they spoke of is an internal switch. It is activated by a valve so that when you let go of the trigger, the machine shuts off. This valve is stuck or the switch is bad. Usually the valve is the problem. I would go to Sears and get ... Pressure Washers

'Dead' DU1100XTP The dishwasher will not start - no lights at all - no indication that anything's working (although I confirmed the unit has power). I've seen numerous posts regarding the control board - is there a problem with these in general? My unit is just beyond the warranty (naturally!) so I'd like to know if there's been any concession made by the manufacturer due to the number of problems. I'd gladly replace the board if Whirlpool would send me one. Thanks.


This may sound simple but... make sure its plugged in all the way. ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

I was using my Karcher 350M pressure washer working fine but it just stopped having tripped the power boards circuit breaker. The breaker now trips each time I switch on the washer. There is no smell of burnt motor and the electric did not get wet when last in use. Appreciate any suggestions or tests that can be made. I have a decent multimeter. Thanks.


... Karcher 1750 Psi Elec Pressure Washer
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1480 seconds