Having problems with your Dishwashers ?

Not getting anypower checked the breaker and that's working fine


Answers :

You need to check that you have power going through the breaker. you do that with a voltmeter.once you know you have power through the breaker you have to check you have power at the Dishwasher with the voltmeter.if you have power there you could have reset on the motor. or the clock has gone bad.I have seen some feed out of a GFI outlet to the dishwasher.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Not getting anypower checked the breaker and that's working fine


You need to check that you have power going through the breaker. you do that with a voltmeter.once you know you have power through the breaker you have to check you have power at the Dishwasher with the voltmeter.if you have power there you could hav ... Dishwashers

I have a GE Quiet Power 3 that has completly died. I cannot get a light to come on or anything to beep when pressing buttons. I checked the circuit breaker and outlet and they are both working fine. I tried pressing and holding the reset button on the front control panel and nothing. It seems to have just died at 2 years old. Anyone have a solution? GE wants $80 just to look at it.


A dead set simply means a cut off of power supply. Open the back cover of your dishwasher . Locate the area where the AC cord is located and look for the plastic fuse holder which is usually installed in one of the AC cord line open it and replace t ... Dishwashers

Bosch DW model SHU53A05UC/17 was working fine until yesterday evening. Went to turn it on and now get nothing. No lights, no power zip. It's on its own 20amp circuit. Checked the fuse and it's not blown. Flip the breaker on/off a few times anyway to make sure. I was installing a floor and used my miter saw on the sump pump circuit (diff from the DW circuit). It blew the fuse a few times. Any chance, on a diff circuit, it spiked and damaged a board in the DW? What part (part #) would


... Dishwashers

I have a GE Quiet Power 3 dishwasher that was working fine last week. Over the weekend I ran it and we could hear a banging noise, so my boyfriend opened it three or four times in a row (during the cycle) to figure out what it was. The fourth time, it went dead. I checked and it had tripped the breaker. I reset the breaker and the dishwasher seemed to be working again, however the lights on the front were flashing (they hadn't previously), and now it will run for about 10 minutes but no water ru


Were you able to figure this out? We have the same problem here! ... Maytag Dishwasher

Amana Dishwasher Model #ADB1500AWB3 (Purchased 7/2009) worked fine on Friday, and last night would not turn on, no green lights at all. We check circuit breaker, and electrical outlet but they were working fine. Do you know what might be wrong?


... Dishwashers

I have a Bosch SMU2046Uc/14 about 15 years old. Sometimes it works, sometimes not, for the last couple of months. Now it has stopped working completely as if no power. Checked the breaker. Another problem - one of our kids just today jammed the door lock on it and we cannot get the door to latch at all. Can you help with any one of these problems? How do you fix or reset the door latch??? What else can we check to troubleshoot the dishwasher? Thanks!


... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

I have a Kenmore dishwasher (363.16222100) that isn't getting water into the unit/tube. All the other cycles seem to be working fine. I've replaced to water inlet valve and it's still not getting water into the tub to start the wash. Checked the water line and it's fine. Any ideas?


The only thing left is to replace the main control board ... Dishwashers

Two days ago my LG dishwasher model lDF 7810BB worked fine. Yesterday I loaded it and the display panel will not light nor show any sign of power. I check the circuit breaker several times and all other electrical items work fine in the kitchen. The 2 year warranty expired 9/08/08


Check for voltage with a multimeter at the wires very near the front, just behind the kick plate. Follow the incoming electrical wire in and remove the little plate the covers the wires/wire nuts. I have seen wires that appear to be connected prope ... LG 24 in. LDF7810 Built-in Dishwasher

My dishwasher so my dishwasher seemed to have quitworking during a cycle. like breaker triped or something. i checked the breaker and thats fine. it seams like its hard wired in though. Would that be right? and is there a fuse or something that could/would blow during a wash? I dont know what model it is or anything it was in the house when i got it. The dishwasher is built in and it seems decently old its a kenmore ultra wash and it has like 10 buttons for the differend cycles on the left and a


Sounds like the fuse on the control blew. you can replace the fuse for\015\012around $20 or you can cut and splice the wires for free. If that doesnt\015\012work then you may have a loose conection in your junction box under the\015\012dishwasher. ... Kenmore 24 in. 15932 Built-in Dishwasher

My SB908WL Westinghouse dishwasher is tripping the switch when it goes to pump out the water. What are the likely problems and solutions please! If anyone has some expertise that would be great. (I have recently checked the soldering on the main panel and touched one point up, the rest are fine it seems). The element is working as there is hot water in the unit. We have small kids so maybe something is jammed in there? How do I get access to check. All input helpful. Thanks!


... Dishwashers

I was using my Karcher 350M pressure washer working fine but it just stopped having tripped the power boards circuit breaker. The breaker now trips each time I switch on the washer. There is no smell of burnt motor and the electric did not get wet when last in use. Appreciate any suggestions or tests that can be made. I have a decent multimeter. Thanks.


... Karcher 1750 Psi Elec Pressure Washer

Kenmore 665.13599k600 was working fine and just quit in the middle of a cycle nothing lights up i checked the breaker its fine..


... Kenmore 13599 / 13594 / 13592 Built-in Dishwasher

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Wont start I've had the washer for many years with minimal problem. Yesterday when I closed the door no light went on and the washer would not start.  After 20 minutes or so it suddenly went on and worked fine.  I thought that it might have not completed its last cycle. Today, however, I had the same problem and it's been over an hour and still hasn't started. (I checked the circuit breaker and it's fine)


Give it a firm push over the door latch once you've closed the door..it might be the door switch not activating. oops.... first and formost isolate from power for 5-10mins and try ... Bosch 24 in. SHU43 Built-in Dishwasher

OE Error I'm getting an OE error which is a drainage trouble error. I checked the hose and the drain, and everything is clear. My diswhwasher runs 98% of its full cycle and usually with 2 minutes to go I get this error. I have 2 opinins as to why this is happeneing. 1. Maybe the clog is in my trash compactor, however that seems to be working fine and my sink is funning with no slow down. 2. My 2nd theory is I have to reset the progam within the dishwasher. Like how sometimes I


Had the same problem and had the pump replaced ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

My frigidaire washer has no power.I check the circuit breaker and everything is fine. The unit was working 2 days ago, it just stopped working.


Have you checked the main wiring under the dishwasher.if the is good and you have power to that point then you need to change the main control board.i hope this helps your problem.get luck ... Frigidaire 24 in. FDB635RF Built-in Dishwasher

I have a model PW 2200 gas pressure washer. It suddenly lost it's high pressure the other day after working fine for @10 minutes. It's getting plenty of water, but the engine doesn't seem to rev up to give it the high pressure. The operating instructions say to check the oil in the engine, and the PUMP before starting, but I haven't found any place to check for an oil level in the pump????Any ideas, I'm very confused.


... Pressure Washers

I have a Miele model G892SCU Plus Type Hg01. There are no lights on the panel and it will not start. It was working fine last time I used it a couple of days ago. It is hard wired to the circuit breaker panel. (No plug) I checked the breaker. It is on and did not pop.


... Miele G892SC SS Dishwasher

My GE Profile dishwasher which may be 10 years old has worked perfectly until today. We push start and nothing happens. We have checked the breaker box and all appears fine. What else should I check?


Check for a blown fuse or ... Dishwashers

No power I went to use my dishwasher today and it wouldn't come on. it's like there is no power. it was working fine. this is all of a sudden. the breaker is fine, it is pluged in. is there something else that i should check like a reset button or something?


Perhaps you should check the fuse in the plug and in the breaker,if there is still no power maybe a circuit has blown in which case you should call yhe manufacturers for qualified technicians. ... Frigidaire GLD2445RFC Stainless Steel Built-in Dishwasher

One day the diswasher was working fine...the next time it turned it on it ran for about 3 min. then shut off and seemed to have no power. I checked the breaker...it was fine. A few days went by and all of a sudden the lights were blinking on the panel. So I pushed the cancel drain button. The water drained out and I then proceeded to load the dishwasher and turn it on again thinking it was just a fluke when it shut off earlier in the week. It did the same thing...ran for about 3 min and then shu


... Whirlpool GU2200XTSS Built-in Dishwasher

Compressor will not engage.the engine runs fine but i can not get any high pressure.happenned suddenly while it was running.i have checked the wand for clogs.also,where is the unloader and how do i unstick it if thats the problem?


Here is the English version of what FLC Florencio said (to the best of my trx abilities :) \015\012\015\012First you must purge the system. Connect the hose to the water intake without starting the machine and squeeze the pistol trigger t ... Karcher 2500 PSI Pressure Washer

Noisy dishwasher My Kitchenaid dishwasher has always been very quiet -- now, it's making a fairly loud grinding noise. It still works fine, water coming out, arms turning -- I'm just wondering if I should get it checked out. Thanks.


... KitchenAid 24 in. KUDP02CR Built-in Dishwasher

Dishwasher not getting water in checked all the water lines, nothing clogged all other aspects of the dishwasher are working fine what could b the problem?


... Estate 24 in. TUD6700KQ / TUD6700KT / TUD6700KB Built-in Dishwasher

I'm trying to get my GE GSD1200G00WW to work. When it is put on the wash cycle, I can hear the pump running but the tub does not fill with water. I checked the float and it seems fine. Water valve maybe?


Confirm 120V across the water valve terminals in a couple of minutes into a wash or rinse cycle. (when you turn it on at the beginning of the wash cycle it will drain first, and then will energize the water valve to fill up.)If there is 120V ac ... GE GSD1000 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1493 seconds