Having problems with your Dishwashers ?

Leaky dishwasher I have a whirlpool lagan dw 110 w dishwasher. Following a wash cycle today it has leaked water over the floor and the light on the dishwasher was flashing. There seems to be no apparent problems and I can't find the manual ... any ideas?


Answers :

Check to see from where your dishwasher is leaking. First, wipe off all\015\012the area around and below the dishwasher and then check for the source\015\012of the leak. If the leak is near the door, give the gasket a look. If\015\012the gasket is loose or worn out, you may have to replace it.

If the gasket is fine, you may want to check the latch. A loose latch\015\012may be the cause of the leak. Unscrew the latch, and then screw it back\015\012in again tightly.

Check all the hoses inside the dishwasher. Ensure that they are not\015\012punctured. Also make a thorough check of all the screws inside the\015\012dishwasher, and tighten any loose screws yourself

Check beneath the door. If the leak is from under the door, the tube of\015\012your dishwasher may have been damaged. You may have to order a new door\015\012from the manufacturer and replace it.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Leaky dishwasher I have a whirlpool lagan dw 110 w dishwasher. Following a wash cycle today it has leaked water over the floor and the light on the dishwasher was flashing. There seems to be no apparent problems and I can't find the manual ... any ideas?


Check to see from where your dishwasher is leaking. First, wipe off all\015\012the area around and below the dishwasher and then check for the source\015\012of the leak. If the leak is near the door, give the gasket a look. If\015\012the gasket is lo ... Dishwashers

We've got an Meile Incognito dishwasher, model G 843 SCVi plus. It purges at the begining of the cycle and then seems to fill with water, but then the red Intake/Drain light starts to flash and the cycle goes no further. I've removed, checked, cleaned and replaced the triple filter and the drain pump but the light is still flashing. I spun the propeller both ways, no problem there. Any ideas for me?


... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

I have a SMEG dishwasher. Can't find the model number on dishwasher or manual. Had two flashing lights and referred to manual - indicates a blocked filter. Cleaned that out, but now when I try to put it on "light" cycle (indicated by wineglass symbol), that light flashes (but no others as would indicate a problem).. All the other cycles work fine. Any ideas? Thank you!


Hi.If only the crystal light is flashing and no other light is on, then that is not an error code. Problem can be a temporary malfunction, or a defective control module or keypad.The delicate (crystal) light flashing with last ... Smeg 24 in. STX2 Built-in Dishwasher

We have a Siemens dishwasher SE25M851. It had the check water light on, so we have checked all water flows which seem fine. There is what I think is an Aquastop connected to the water hose, which I have no idea if the problem is there, but when I now put the dishwasher on there is a burning smell coming out of it, so have had to turn off power supply. Can you shed any light to the problem?


... Siemens Dishwashers

FDW60 dishwasher - taken apart pump and that is clear. Seems that dishwasher fills, and empties and heats all OK but water wont go around the machine ie the motor pump doesnt start - any idea how to take this out and replace without having engineer around? Taken small pump apart and its clear. First of all the Eco and fast light flashed, then we took it apart with some direction from online discussion advice. Now Eco and Pre wash lights are flashing. Machine empties water, then fills with


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

FDW60 dishwasher Hi My dishwasher is about 15 months old and the problem I have is that it seems to stay on pump and the Ecco45 light is flashing.  A repair company looked at the machine and said that the motor looked like it was leaking and water was getting in the bottom setting off the micro-switch.  He contacted Hotpoint who fitted a new motor today at a cost of £89.85.  Went to use dishwasher tonight and we still have the same problem.  The dishwasher started the washing programme for about


I've just (as of 10 minutes ago) had the same problem. I followed the advice given elsewhere in this forum and removed the bottom cover - water running out so needed a big towel to mop it up. I stood the machine upright and restarted it - no problem! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

FDW60 Fault Hi, I have exactly the same problem. My dishwasher starts and washes ok but appears to get very hot during the drying phase and then the two lights fast and eco flash warning of a heater problem. I suspect either the heater, thermostat or control PCB. As the rest of the cycle seems of and the water gets hot then I'm assuming the heater and thermostat are OK. When the dishwasher attempts to dry is when the problem starts. Did anyone find out what there fault was? Thanks


Hold down the start key and you will re- set the D/W. Please Rate This !!! Thank YOU !!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Dishwasher We are having a problem with our Whirlpool ADP5540 dishwasher. We have just moved into a new house with this model dishwasher and have tried running it on a number of cycles. It always seems to stop part way through and the start button then flashes three times. Any ideas what the problem is or how to fix it?


If\015\012this is a blinking "clean light", this is a common problem with some\015\012of the Kenmore\015\012and Whirlpool models. I believe the problem is attributed to water supply\015\012temperatures being too low when filling. Apparently, th ... Dishwashers

We have a Kenmore Ultra Wash Dishwasher Model number 665-13859K601. The Normal wash and the Cancel (drain) buttons are flashing red on the control panel. No matter what we have tried, we have been unable to correct this problem. Obviously the dishwasher does not function. When you close the door the lights keep flashing and no button combinations seem to do anything. I have looked at the troubleshooting guide that came with the dishwasher, however there is no


... Dishwashers

Dishwasher won't start. Clean light keeps flashing. I have tried cancelling a couple of times, and it goes through a 2 minute process and goes right back to the flashing clean light and not allowing it to start. I have already tried shutting off the breaker as suggested by someone but it did not solve the problem. Any other ideas?


Hi\015\012 \015\012Thanks for using FixYa. If the clean light flashes 7 times, pauses, then repeats...When the dishwasher doesn't sense a water temperature increase, it stops working and locks t ... Dishwashers

Quick Rinse light was flashing at end of cycle. Opened and closed door and pushed Start. Quick Rinse and Cancel/Drain light are now flashing and machine won't start. Turned off power supply (30 seconds) / turned on power supply and then tried again to start the dishwasher, but same problem. Control panel seems to be frozen at the Quick Rinse/Drain mode and will not cancel. Help! Thank you


Ok try this, open the door and then hit these buttons in the following combination. HI TEMP - DRY - HI TEMP - DRY...then close door and press cancel...then wait for the pump to shut down. you should be able to run a cycle after this...If this fails ... Dishwashers

Hello, I have a Bosch SGS43A42UK dishwasher with a problem in that the cycle does not seem to end - it seems like the dishwasher is still trying to remove water long after it has been extracted. I pressed both buttons together and the *End* light flashed and then the cycle ended. Help, please?


... Bosch Dishwashers

FDW60 Hello, I have a Hotpoint FDW60 dishwasher. It seems to have the usual quality issues but the actual problem is different to most I see on here. The machine has only been used about 20 times, but yesterday the following happened, I loaded and selected intencive program, when I pressed start the machine made a shriek/chipping sound, it seemed to run for about 5 seconds then stopped with the power and prewash lights flashing erraticly for about 3 seconds then was totaly dead, no power light o


Tom,\015\012If your dishwasher is still under warranty, best thing will be to contact Hotpoint's service center for repair the problem. ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

My Kenmore model 665.16022401 has the problem w/ the clean light flashing. I tried the bottom combo of hi temp wash, heated dry, high temp wash, heated dry and it re-set my dishwasher but then after I tried to run a new load it doesn't seem like it finishes all the way through because there is still soap left in the soap dispenser and the dishes arn't all clean, plus the green clean light begins flashing again. Don't know what to do.


... Kenmore 24 in. 16022 Built-in Dishwasher

Whirlpool Gold Quiet Partner Model # GU980SCGQ2 The dishwasher normal light flashes on and off continually. The dishwasher won't stop cycling now, everything seems to work normally other than it won't stop cycling. I've attempted turning off the breaker- no luck. Attempted resetting the dishwasher- no luck. Any assistance would be appreciated. Is this a problem with the control module? The thermal fuse?


... Whirlpool 24 in. GU980SCG Built-in Dishwasher

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Hi i have a Candy CDI 1012/B Intergrated dishwasher and 4 lights are flashing during the first programme then system drains and stops showing four lights lit. We have no instruction manual or service manual this would be good to get hold of as we have serveral of these machines. any idea what the problem is to save us time investigating it. Thanks Paul


Hi. The four leds flashing quickly at start of the cycle means that there is an inlet problem. Check that the inlet hose is not bent, blocked or kinked, ensure that water has sufficient pressure. The inlet valve can be tested reading Ohms at valve te ... Dishwashers

Fdw60 dishwasher yet again my dishwasher has broken again, now it is trippin my electric in the house, the problem that was starting up was a eco light flashing i read on here what to do and that seemed to of fixed it, but since i did that it starts up and as soon as water starts to enter it trips my electric and advice would be great


Hold the start key down and it should re-set . Please Rate This ! Thanx!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Hello, My Kenmore elite dishwasher model 665.17282.400 seems to have a problem. The CLEAN light is flashing and can't do anything else with it. Do you know what thew problem is, or how to reset it. I tried cotting off the power to the unit but to no avail. Please help ASAP


Try pressing the heated wash then heated dry one after the other about 5 times. this should reset the unit.\015\012\015\012\015\012--------\015\012in some machines there is "Hi temp scrub " and "air dry" so press this ... Kenmore 24 in. 17282 Built-in Dishwasher

Have a whirlpool G2P DWI / 1 WH integrated dishwasher - when put on [70C] it seems to work ok and washes dishes but then after what seems to be the full cycle it just beeps continuosly - when opened the start button is flashing and the green light is on under the pre-rinse symbol. There are two bar codes down the side: 8542 347 15810 and 33 0451 014488. It's been in for about 3 years and have had no problems with it. Can't find instruction manual.


... Whirlpool Dishwashers

Our Miele 75 carat dishwasher won't drain. The red light comes on, but nothing seems to empty it. We've checked the drainage pipe, but the problem seems to be inside the machine. We've tried using a drain cleaner, but it has had no effect, even after 24 hours. Any ideas?


Just on the offchance, try the following. throw down an old towel, and tip the appliance right onto its side. If the anti-flooding switch has got stuck, you may be in luck this may reset it. (Have successfully used this technique several times on our ... Miele Dishwashers

Have a whirlpool G2P DWI / 1 WH integrated dishwasher - when put on [70C] it seems to work ok and washes dishes but then after what seems to be the full cycle it just beeps continuosly - when opened the start button is flashing and the green light is on under the pre-rinse symbol. It's been in for about 5 years and have had no problems with it. Can't find instruction manual.


... Dishwashers

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers

Hi - My Electrolux ESL63010 dishwasher seems to be stuck mid programme. It was part way through a programme when we had a pipe burst. Pipe all sorted now but the dishwasher just makes a noise like it is asking for water but nothing happens. When you open the door, it makes three short beeps and the light flashes on the programme menu. Any ideas how to solve? It definitely is not the pipes as the washing machine feeds from the same pipe and is working fine. Help!


... Dishwashers

Whirlpool Quiet II (DU110XTPB1)... Two problems (maybe it's one)... Start/resume light flashing and won't stop. I have tried on the different button combinations from this website and other websites and none of them seem to make a difference. The flashing continues. That's problem number one. Problem number two is that it seems to go into some sort of washing cycle in completely random intervals. When it's in one of the random washing cycles the following lights are on; Normal Soak and scour


Hope it's under warranty, maybe logic board, poor motor design causes main PCB failure ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2413 seconds