Having problems with your Dishwashers ?

Our dishwasher lets the water in but does not spray the water on the dishes to clean them. It makes a thump type sound when we hand turn it to the washing cycle and does not pump any water out when we turn it to that cycle as well! Please advise! thks Bob Rupnow


Answers :

SOUNDS LIKE THERE IS AN OBSTACLE IN THE PUMP IMPELLER OR THE MOTOR HAS A PROBLEM. THIS IS FROM THE THUMP DESCRIPTION. THERE ARE OTHER POSSIBILITIES WITH THE RELAY THAT CHANGES FROM WASH TO DRAIN, BUT USUALLY HAS A DIFFERENT MALFUNCTION.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our dishwasher lets the water in but does not spray the water on the dishes to clean them. It makes a thump type sound when we hand turn it to the washing cycle and does not pump any water out when we turn it to that cycle as well! Please advise! thks Bob Rupnow


SOUNDS LIKE THERE IS AN OBSTACLE IN THE PUMP IMPELLER OR THE MOTOR HAS A PROBLEM. THIS IS FROM THE THUMP DESCRIPTION. THERE ARE OTHER POSSIBILITIES WITH THE RELAY THAT CHANGES FROM WASH TO DRAIN, BUT USUALLY HAS A DIFFERENT MALFUNCTION. ... Dishwashers

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Inlet/Drain light is on. I have cleaned the drain pump and non-return valve, rinsed under water, removes all foriegn objects, turned the drain pump impeller (which turns freely) and carefully replaced the non-return valve and secured it with the locking clamp. I tried turning off the dishwasher and teuned it back on. No warning light shows but as soon as I try the dishwasher on a wash cycle it fails to pump water into the machine and release the washing tablet door. The programme unit makes a no


Is the water inlet turned off by chance? Is there no water at all inside the dishwasher? ... Miele 24 in. G643Vi Plus Built-In Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

My dishwasher has stopped pumping water in the tub. You can turn it on to start the cycle and it comes on but it has stopped pumping water to wash the dishes. It will go all the way through the cycle and never wash a dish


... GE 24 in. GSD2220Z Built-in Dishwasher

My Kitchen Aid KUDS01FLSS2 dishwasher does not spray water thru the wash arms nor do they seem to turn. Additionally, one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" when rotated by hand. The spray arm assembly appears true on visual examination. The unit fills, cycles and pumps out in an apparent normal way. While on this site a while back I was advised to clean the unit and referred to a downloadable repair manual that was, in fact, not


Hi.The fact that "one of the the bottom arms hits the "cap, internal rear feed" where it clips to "feed tube assembly" would suggest a tubing problem. However there are more faults that will result in no spray. Testing in this case can be ... KitchenAid Dishwashers

Dishwasher Repair I have a Frigidaire dishwasher that came with the house. The house and washer are probably about seven years old. It woked fine for the first few months but now, when I turn it on to wash it fills with water but then it will not go into wash cycle (i.e. there is no water sent into the dish compartment). It will go through every cycle by filling and emptying through wash and rinse but no water goes into the dish compartment. Is there a pump that is perhaps not working? How is th


Ebers, you have a seperate wash and drain motor on this model. When you remove the bottom panel the drain pump will be on the right and the circulation (wash) pump will be in the rear. You are going to have to verify that you have power getting to t ... Frigidaire 24 in. FDB421RF Built-in Dishwasher

I have mod. # FDB1050REB0 the top rack wash/rise arm is not turning at anytime during the wash cycle--- We are not covering the hole into which the water is being pumped---- the bottom washing is turning---- this leads me to to believe the line to the top arm is obstructed from the pump to the wash outlet (in the top of the machine)---- what can I do to check the line?


Hi\015\012\015\012Please check if something is blocked near the top spray arm\015\012and also make sure that all holes are open. Use a sharp metal pin to clean the\015\012holes on the top spray arm. Make sure the water pressure is not low ... Frigidaire Dishwashers

Amana Dishwasher dishwasher will fill with water, then will proceed to just hum through the wash cycle, no water is pumping through the turning blades. It will stay humming until you turn it off by hand ( dial will stop mid way through cycle)


Sounds like something is jamming your wash inpeller start at the washer arm and go down till you get to the wash impeller and see whats sticking it like broken glass small peice of bone toothpick etc ... Dishwashers

Turns on, the entire cycle runs, but no water pumps through the sprayer. There is water present on the bottom....and I can here the water pumping in at the beginning of the cyle....but the dishes are not being 'washed' by the sprayers. I have disassembled and cleaned the entire inside and sprayers to no avail. Im thinking its a pump/motor issue but Im not sure because the sprayers spin, the heat comes on, the detergent dispenses....but no water is being sprayed. Thanks.


Yes i agree, your pump is not working as it should. J.\015\012\015\012That said if this machine is over 3 years old, replace it. The new ones are so much quieter, better, and cheaper to operate. J. ... Maytag MDBH955AWS Stainless Steel 24 in. Built-in Dishwasher

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

My Bosh Model# SHE4AM02UC/01 Is not cycling. Started with the soap dispenser not opening, progressed to the drain pump not staying on. When you turn it on, the pump runs for 2 seconds. water solenoid opens for another two seconds, and then the "clean" light comes on. If I go to quick wash, or to pot scrubber it might do a regular cycle. I did pull the pump to remove a piece of glass before this all started, but can't imagine that would be the cause.


... Bosch SHE4AM02UC 24 in. Built-in Dishwasher

Whirlpool dishwasher part #3385181. Machine had gone thru wash cycle and was starting to dry. Smelled electrical burning smell, opened washer door and washer was filled with smoke. Turned everything off, cleared smoke, and the washer water dispenser is very hard to turn. Washer has symptoms of burnt up motor that turns water dispenser. Machine is 12 years old. With cost of replacement motor and possible part (pump?) that might have clogged and caused motor freeze up, is it worth fixing or junk


... Dishwashers

Asko 1605 cycle stopped, pump keeps running, water pumps out but will not progress to the rinse and wash cycles. Timmer will turn and detergen dispenser will open. Pump keeps running


Thanks my Asko did the same and tilted it forward, drained excess on the floor, even though I thought i'd bailed the whole lot and woolaa fixed - thanks x ... Dishwashers

Dishwasher wont fill with water. just before it stopped filling i was turning the dial (a lot) between the wash cycles back and forth to attempt to get it to fill and drain (I didn't let it go through a cycle). We also removed the hose from the machine as it had split and replaced it and we had the machine tilted on it's side. the dial still clicks round but it sounds like the pump is going and it doesn't seem to be filling with water. Help


Hi. I suspect that the timer mechanism will be the culprit here, but i recommended to inspect and test the water inlet valve, before replacing the timer. The valve is a known problem area, as well. Follow the valve inspection procedure below, careful ... Fisher DS603W / DS603B / DS603I Dishwasher

I have an indesit dishwasher dif16, suddenly it stopped going through its washing cycle, at present it will fill with water and the powder door will open it makes a noise as if a motor of some sort is running and thats it, it will not wash, if i switch it off the appliance the water will pump out, please can you advise what i need to fix this


... Indesit 24 in. D61 Free-standing Dishwasher

Dishwasher malfunction MOST OF THE TIME it shuts itself down before fully filling with water - SOMETIMES it doesn't shut down until the minute the wash pump starts - SOMETIMES it washes for 10 or 20 minutes before shutting down - SOMETIMES it will even run a whole cycle, BUT it doesn't open the soap dispenser door - tried doing a diagnostic run but after it turned on all the lights on the panel it started to fill with water and shut itself down......... HELP


Follow this steps and fix it. God bless youFloat Switch\012\012\012The float switch may be hung up and this can cause the dishwasher to be stuck in a cycle. Check the ... Dishwashers

I have a Bosch SHX43M05UC Dishwasher. To wash, you select the cycle and then close the door to start the wash. Now when I push the on button, the pump turns on. I can't tell if it's pumping water or not but it's not supposed to start until the door is closed.


... Bosch SHX43M05UC Built-in Dishwasher

Bosch SHX46A (6 years old) Selected regular cycle, pressed On and closed door. Cycle did not start normally. Pump runs, but no water is coming into the DW. I confirmed the water supply line is turned on. I opened door, turned off On/Off switch, then poured water into drain. Then turned On/Off switch on. DW began pumping water OUT of the DW. Also, it doesn't matter if the door is open or closed - if you turn the DW on, the pump will run. I suspect a problem with the electrical controls, or perha


From your description, I doubt that the problem is door latch is the cause.\015\012\015\012The first thing that a modern dishwasher does before it begins to fill with water is run the drain pump.  It appears that this DW is not progressing ... Bosch Integra® 500 SHX46A0 Dishwasher

We have a Bosch Model SKT5102GB/07 and the problem is as follows; we load the dirty washing and start the washing process, the machine then goes through the full cycle of wash. Once finished you open the door and notice that the washing is still dirty and a large pool of water is laying in the bottom of the machine. We have had an independent engineer look at the machine and he has advised that the pump needs changing. Look forward to your reply, thank you. Regards Michael Ballard.


Replacement parts are available here\015\012http://www.repairclinic.com/SmartSearch/SmartSearch.aspx\015\012\015\012on the narrow ... Bosch Dishwashers

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

DISHWASHER WONT GO INTO WASH CYCLES,WHEN I PUSH START GOES CANCEL/DRAIN,CAN HERE PUMP RUNNING THEN IT WILL TURN OFF,THERE IS NO WATER IN THE BOTTOM,SEEMS LIKE STUCK IN DRAIN CYCLE


... Whirlpool GU2300XTS 24 in Builtin Dishwasher

My hobart lxi pumps down after each wash cycle Already Tried: Cleaned all three water level probes Checked water inlet solenoid (all good) Checked inlet water pressure (all good) Checked drain pump which is supposed to pump out 3/4 of a gallon at the end of each wash cycle but it pumps 2-1/3 gallons then pops up the infamous wrench!


... Hobart 24 in. LXIH-3 Built-in Dishwasher

Dishes not clean after running. Dishes and glasses have a white residue on them after drying. Water is turned on and seems to ok. When I open the washer after the wash cycle starts there are several inches of water in the washer and the jets seem to be functioning. Thanks for your advise.


Hi If you are noticing that the dishes are not clean, then there are a few things to check for. Check the soap powder if it's kept in a dry environment. Also try replacing the powder with something like a gel or liqu ... Bosch SHU9925UC Built-in Dishwasher

Water sounds like its comming to dishwasher after awhile dial turns(timer) disher wsher goes in to dishcharge pumping out water but inside of dish washer seems dry like no wash cycle took place


Look inside the dishwasher for large plastic mushroom-shaped thing in the bottom.\015\012This is a float.\015\012Sometimes a knife or fork or something else gets in the bottom of the dishwasher and won't let the float go down. When the float is up li ... Asko D1706 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1880 seconds