Having problems with your Dishwashers ?

PROFILE 3 GE DISHWASAHER LOCATIOM OF FUSE RREQUIRED THANKS


Answers :

Thats a easy one go to searspartsdirect .com and give them the model# and you can order part from them. you can also see an image of your unit. let me know if i have been of any help and post me back with a 4 thumbs up rate
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

PROFILE 3 GE DISHWASAHER LOCATIOM OF FUSE RREQUIRED THANKS


Thats a easy one go to searspartsdirect .com and give them the model# and you can order part from them. you can also see an image of your unit. let me know if i have been of any help and post me back with a 4 thumbs up rate ... Dishwashers

I have a GE Profile Triton Dishwasher and it has worked fine for about 8 years. Suddenly it will not reset. The reset light blinks after reset but you can not choose a normal cycle afterwards. I shut of the machine by pulling the fuse box. I turned it back on but again it will not reset?


Hello, how are you?\015\012It sounds like you have a stuck key on the keypad, preventing you to push any other key.\015\012I've seen this problem many times in the past 4 years.\015\012Good luck.\015\012Ned ... GE 24 in. Profile PDW7800 Built-in Dishwasher

GE Profile GSD4010202AA Built in Dishwasher acts as if no power


1. turn breaker off to diswasher. 2. remove bottom access cover. 3. remove cover over electrical connection box on right side. 4. hold each wire nut connector and firmly tug on one wire at at time to make sure none of the wires pull out of the wire ... GE Dishwashers

GE Profile Dishwasher PDW7300 Died on me!


Thanks for the pointer on the arcing. Funny thing is .. I did the electrical myself and I always make sure things are tight and connected properly. Was a little shocked to see the melted wires and caps. I soldered them this time .. if it happens agai ... GE Dishwashers

Bimetal fuse The incoming power was blinking off and on due to a storm, it caused the bi metal fuse to fail in the dishwasher when it was not operating, the fuse was replaced with kit #w10258275, now two weeks later the fuse has failed again while operating.These fuses are expensive, I would like to know the value (amps) of these fuses so that the system can checked to try and find out the reason for failure, or maybe you might have an idea where to start. Thanks Tad


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Dishwasher 66513752K601 keeps blowing the thermal fuse. (Bi-Metal W10258275). I have replace the Thermal fuse several times. After i replace the fuse for some reason after a few months or less it will blow it out again. I have also replace the front panel assembly after it stopped working correctly. I would like to know how to test the dishwasher to find out the root cause of the fuse issue. I don't want to be replacing the fuse every time and don't have the $$ to buy a new dishwasher. Everythin


... Dishwashers

Dishwasher I have had above integrated dishwasher which is intermittently tripping the mains fuse. Power is getting to dishwasher and the washing cycles work until a certain point (not the same time) where a loud bang can be heard and the main fuse is tripped. Reset the main fuse and power still gets to the dishwasher and it works again. It has just started to trip the fuse when its not running any cycle (just when power is getting to it). I've checked the fuse on the spur and it looks ok. I hav


Its quite common for the interferance filter to fail on these models its situated in the base of the dishwasher connected to the mains block usually when they fail you can see black dust around it, ... Neff 24 in. S5456 Built-in Dishwasher

Hotpoint Dishwasher BF1620 blew the main fuse circuit in fuse box during mid cycle wash? Re-set main power fuse circuit but now as soon as Dishwasher switched on immediately blows main kitchen power fuse in fuse box? What is problem?


This is happening because you have a very bad fault, a Phase to Earth short, problem. Leave machine UNPLUGGED, Breaker/Fuses OUT. do NOT use it, nor Touch it, It is possible to get severe electric shock. PLEASE get a registered serviceman to inspec ... Hotpoint 23 in. BFI62 Built-in Dishwasher

WHAT ARE THE THERMAL FUSE SPECIFICATIONS FOR KENMORE ELITE MODEL 66513122K701SERIAL NUMBER FY1211868 AND WHAT IS THE PART NUMBER FOR A THERMAL FUSE KIT? WE HAVE HAD TWO FUSES BLOW AND THERE DAMAGE TO THE WIRING ON THE LEFT HAND SIDE OF THE CONTROL PANEL THAT CONNECTS O THE SWITCH. THEIR IS DISCOLORATION ON THE PARTS AND WIRING. WE HAVE SEEN EXPERTS STATE THAT IN ORDER TO CORRECT OUR ISSUE WITH THE FUSE BURNING OUT WE NEED A THERMAL FUSE KIT AND WE NEED THE SWITCH AND THE WIRING THAT CONNECTS TO


Http://appliancejunk.com/ge/dishwasher/31-9137.pdf\015\012\015\012A ... Dishwashers

Have kenmore quiet partner 1 dishwasher. Fuse failed a year ago after 1 year in service, panel has no lights, suspect fuse again. Need to know fuse location and description of fuse


You didn't list model number. remove screws on inside of door to have access to controls. There should be a thermal fuse square object with two wires attached. Some brands now come with short pigtail wires, so bad terminals are eliminated. IF it's a ... Kenmore 24 in. 16222 Built-in Dishwasher

My Whirlpool GU2400XTP dishwasher keeps blowing the fuse. It sat up for 6months because the control panel went out and I couldn't afford to get a new one. Finally replaced the panel and the thermal fuse blew during the first wash cycle. I tried to put a 15AMP fuse in it's place to check it out before I bought a new thermal fuse and it too blew during the first cycle. Any ideas?


Are you replacing the wires along with the fuse? It is important to change the wires too as they are usually the cause for the fuse blowing. Be sure and get the fuse kit that includes the wires. \015\012\015\012Is your water too hot? Hot ... Whirlpool GU2400XTP Built-in Dishwasher

I have a kitchen aid dishwasher model number KUD101TJBLO. I have had the thermal fuse replaced numerous times. It may run two weeks ir it may rub two cycles then the fuse blows. My serviceman has given up on finding a solution.He has replaced the control board and the door switch. However it continues blowing the fuse. I read on the internet that you need to replace the entire wiring kit that comes with the fuse but my repairman says this will not fix the problem and refused to replace the kit.


Hi\015\012\015\012\015\012Thanks for using FixYa. Please check for the short on the wires near the heating element. Also check the resistance of the heating element, it should not be more than 1.6 K ohms. Also ma ... KitchenAid Dishwashers

IDL750 - Fuse trips when turned on. HELP! We had some electricians here to install a new electrical socket for a new fridge. They put the new socket in the same wiring as for my existing dishwasher!! The first time I tried to start the dishwasher cycle with the new fridge plugged in, the circuit box fuse tripped. Now, even with the fridge turned off, the dishwasher makes the fuse trip when turned on. Is there a fuse inside the dishwasher that has blown and needs to be replaced? or a ground brea


Hi.The first step is understanding if the problem is the socket or the appliance. Find an extension long enough to reach a different socket. Move the appliance to reach the power cord, and connect the dishwasher to a different power sock ... Indesit 24 in. IDL700 Built-In Dishwasher

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti


Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher

Kudc10fxss4 I have a KitchenAid KUDC10FXSS4 w/o any power. Circuit breaker is on, and it's getting power. But there are no lights on the display. I called a parts place to see if I could order a thermal cut off fuse. But the representative stated there is no fuse listed for this model. Any ideas on what would be causing a loss of power? Seems odd/wrong to me that there wouldn't be a fuse. If there is a fuse, would it be located in the door (the control is built into the door, such


... KitchenAid Dishwashers

When on/off button de-selected large flash from top of door. Main consumer unit tripped and fuse in plug found ruptured. Fuse replaced cb reset but dishwasher has no power. Fuse rechecked found to be good.


Dishwasher stripped down and found MAIN WIRING HARNESS chaffed agains door during opening and closing. New loom in region of £100 so repared old loom. ... Dishwashers

Hi I have the Kitchenaid dishwasher KUDIO1FLSS2 and all the buttons work except the two most important ones, the heavy and normal cycle. I had a service person out about 6 mo. ago and he said the control panel was about to go bad and replaced a fuse. He ended up coming again a week later and replacing the fuse with a stronger fuse. Now it's acting up again and I'm sick of hand washing dishes and don't feel like handing over another $300 or more if I can do it myself or maybe I just need to buy a


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

KitchenAid dishwasher: KUDS01FL - I have had to replace the fuse every year and now I can't even get through on cycle with the fuse going. It is now dead again! It almost makes it through the full cycle and then stops (fuse blows)- no power - and there is some water left in the bottom which I have to physically remove. I spent a fortune on repairs every year since I bought it and would like to try to avoid another charge. I appreciate any help that you can offer. Thank you, Carol


I would check the pump. It may be slightly jammed or have debris which is causing it not to fully move or cause it to move very hard popping the breaker. Also with a jammed or broken pump, that can also cause water to be left in the bottom of the mac ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a Whirlpool Quiet Partner 3. It sat up for a few months because the control panel went out and it took a while to save up and order a new one. Now it blew the thermal fuse. I put a 15amp automotive fuse in it to try it, and it runs until it fills up and blows the fuse again. I am trying to figure out how to test the motor and the heating element to see if they are shorted. My local repair shop told me that they want to replace my new panel with their panel first, and that after that


A 15amp automotive fuse is rated for a 12VDC system in an automobile, not a 125VAC houshold electrical system in an appliance. I don't think your automotive fuse can handle the start current being drawn by the main wash pump as the dishwasher starts ... Dishwashers

Hi, i use a karcher hds601c for valeting. Today for sum apparent reason, halfway through my job, the power cut out, realised the fuse had gone, an hour later i replaced the fuse but it tripped again. i went through about ten fuses, sumtimes it would work, then trip again. do you think it could be the motor or water pump. its only 18months old.. thanks


... Karcher FactoryReconditioned 1400 PSI 13 GPM Electric Pressure Washer K

Hi I have a whirlpool diswasher which is about 7 uears old which has blown the fuse (and the mains trip) half way through a cycle. Replaceing the fuse has resulted not resulted in the restoring of power to the unit. Is there anything simple I could check (in line fuses etc.)? Cheers


Some whirlpool models do have a thermal fuse in the consloe mounted to the main control board housing, might looke to see if it has one and if it is good ... Dishwashers

Bosch exxcel Last night when i turned on my dishwasher it tripped the fuses in the house. I have changed the fuse in the plug, but it continues to do it. The lights on the display flash up once and then the fuse box trips again. Not sure what else to check. Can any one give any suggestions?


The likely cause of this is a failed heater element which would cause the fuse to blow. You will need to get the heater element checked out and replaced if necessary. A visual inspection of the element may reveal the problem jf not an electrical test ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Kitchenaid model kudso1dj blew a fuse and will not respond after a new fuse was installed in the fuse box


Good day,hope this link below will solve problem.kitchen ... KitchenAid KUDS01DJ - Multiple Color Dishwasher

My GU2500XTPSO would not start. The panel wouldn't light up. My husband ordered and replaced the thermal fuse but the new fuse burned out immediately. Can you help? It will not start or light up. Should I look at another problem causing the thermal fuse to burn out?


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

I have model number KUD 101TJBL0. I have spent about 300.00 on repairs. It keeps blowing the thermal fuse. I have had it replaced sev. times. My repair man has given up on solving the problem. I did read on another website that you need to replace the wiring kit that comes with the fuse. Me service man never did that and when I asked him about it he said that is not the problem and would not replace it. So, before I just scrap my diswasher and but a new one I thought i would order another fuse k


Hi,This applies mainly to Kenmore Dishwashers with the model number\015\012665.15835791 but also to any Whirlpool or Kenmore dishwasher with an\015\012electronic display. There are several possible trouble makers on this\015\012dishwasher ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0319 seconds