Having problems with your Dishwashers ?

Model # SRI45T25EUEI Unit starts to fill, float in matrix activates micro switch, then drains. Continues this cycle. No leak to base float.


Answers :

Hi,
\015\012 I think this is detecting another error condition, so skipping the entire wash cycle; Either that or the main program board is at fault.
\015\012
\015\012The fast way to sort this is to replace the main control board, and while it is out, check the heating element and temperature switches are ok.
\015\012
\015\012This can be done at the board connections without taking the unit out.
\015\012
\015\012From the look of it though - it's the main board, as it's skipping a lot of functions.
Hi,

It seems that the flapper breaks off or the spring cannot keep the drain port closed causing the water to drain as it fills,these are the usual defective parts.You might need to disassemble the pump and motor to get into the drain flapper area.

9a88c1f.jpg


Let me know, if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Model # SRI45T25EUEI Unit starts to fill, float in matrix activates micro switch, then drains. Continues this cycle. No leak to base float.


Hi,\015\012 I think this is detecting another error condition, so skipping the entire wash cycle; Either that or the main program board is at fault.\015\012\015\012The fast way to sort this is to replace the main control board, and ... Dishwashers

Hotpoint dishwasher HDA467-02 AD leaks suds/some water at the bottom of the door ONLY during the wash cycle. There is no leaking during the rinse cycle. Have replaced the bottom flange gasket (Part WD8X5100). The leaking stopped for awhile then started again. Float switch moves freely. Any ideas?


Tilt dw back ... Hotpoint 24 in. HDA2000Z Built-in Dishwasher

Bosch Classixx dishwasher: Initially no water feed and 'water check' light came on. Removed side panel, emptied water from base. Ran OK for a week or so. The problem then repeated so side panel removed, float switch operation checked (OK) drained water from sump below polystyrene float. Ran OK but contents came out dirty and cold - no heat. Side panels off again, water in base but no obvious leak when watched during cycle - still no heat. Help please.


Http://www.repairclinic.com/Dishwasher-Repair-Help\015\012\015\012\015\012\015\012 ... Dishwashers

I have a Bosch Exxcel dishwasher which runs the drain pump constantly even with the door open and despite there being now water in the machine at the cycle wont start. I have checked the warer amtrix and the ffed hose to the sump for blockages. The float switch operates OK but when the water drains down the float drops and the water is pumped in, then the float rises and water leaks out and the drain pump kicks in again and no more ater will come in unless you push the float down. Inside the bas


I am not sure about this model but most models run a drain cycle for a set period at the start of a wash cycle and then move on to normal filling and cycle of machine provided the various switches are at the low level it will carry on to its set cycl ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

Hello, my Bosch Classixx dishwasher SGS43E42EU/21 has me stumped. It starts by taking in water but when "filled" pumps out for a couple of seconds then refills for say 10 seconds more before another 2 or 3 seconds of pumping out. This cycle continues for ages without starting to wash. I've tried various things: - checked the Auto Stop valve isn't being activated by leakage (removing the polystyrene float and bottom tray makes no difference - there's no leak) - the valve seems to operate it


Hello Dave,\015\012\015\012Sounds like an overfill problem - the symptoms are consistent with a failed pressure switch. Water enters the dishwasher through a chamber which has a float arm connected to a small microswitch -this is the pres ... Bosch Dishwashers

Cycle interupted until pressure applied to door, near control panel. Fault is intermittent. Sometimes I need to lean a chair against it to keep it going. Door clicks shut nicely and does not leak. Cycle always starts but often will not complete without a thump. Is pressure inside bowing the door and activating a safety switch?


Problem on the safety switch\015\0121)try to adjust the safety switch to contact properly with the door.\015\0122)any screw is there on switch means loosen the screw &adjust to contact with door. ... Bosch 24 in. SGS43C02 Classixx Built-in Dishwasher

Bosch SMS4012GB dishwasher. Refused to fill. Found tray full of water in base of unit. Mopped up water about 2 litres. Machine works but lower reservoir on the side of the machine with float switch overfills and overflow leaks about an eggcup full each cycle. What is causing the overflow please?


An electric switch activated by air pressure. This device detects air pressure exerted on it through a flexible tube connecting it to part of a water tub. \015\012When activated, this switch then opens an e ... Dishwashers

Ikea/whirlpool dishwasher built in 851108915000 will not start the program rinse light flashes and the pot 70 deg light stays on i believe this error means float switch activated but the base is clear. any ideas?


... Dishwashers

Water Leak My dishwasher is an Ariston Advantage AF250: I have been told that internally its the same as a Hotpoint DF55. It intermittently leaks water onto the floor from the front at its base during use. At one time it ruined the motor which I had rewound and at the same time I made a new polystyrene float for the base pan overflow switch. All was well for months, but now its leaking again. I have blown through the tubes from the drain filter well to the pressure sensitive switch, but all


Hi there, dishwasher leaking might be due to either of these causes, check these:Main tub sealNote… If the main motor of your dishwasher is mounted vertically, beneath the center bottom of the dishwasher, the foll ... Hotpoint 24 in. DF55 Free-standing Dishwasher

Whirlpool DWF417W, Type 12155 A couple of weeks ago the machine failed to empty, leaving dirty water in the machine at the end of the cycle. Start a new program it emptied & all was then well. A couple of days ago we started a wash cycle as normal, shut the door, the pump normally runs for about 10 seconds then the cycle starts. However the pump just runs continuously?? After looking here there seemed to be a few links to the subject of water being in the base & the anti flood switch being ac


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

Asko Dishwasher starts the cycle by pumping out as it should. But does not stop pumping nor advances. If I click it forward manually it starts to fill and then before overfilling goes into pump out without washing then just repeats this. Pressure switch tubes and air trap chambers are clean and no leak to trip spill switch. I'm guessing It is either the timer or faulty pressure switch any clues ???


If has "mother board" then water could have got in.\015\012\015\012Here Asko is low cost make so check cost before serviceman calls & charges & charges and so on. ... Asko D1706 Built-in Dishwasher

Neff 4456 water resevoir not filling. Checked float switch and all OK. Checked water supply and all OK. Filled resevoir manually from top of resevoir and program cycle starts but stops when rinse is required.Have stripped down and cleaned switch with float switches as I have had that problem before getting clogged. Any ideas


... Neff 24 in. S4456 Built-in Dishwasher

I just installed a Bosch shx43R55UC/64. Upon starting all lights are on and I cannot select a cycle. When I shut it the unit starts but will not fill with water. The float switch is working, No wat


U need to clean out the water chamber on the left hand side and the diofram too ... Bosch SHX43R55UC Dishwashers : Built in Dishwasher

Roper Dishwasher leaks from float or float switch onto floor


You could be usiong way to mauch soap try filling only one of the soap trays or even try doing one wash without any soap at all\015\012 this unit tends to do this if you have to much soap in the unit left over from the last load...\015\01 ... Roper 24 in. RUD4000M Built-in Dishwasher

I am trying to fault find a Hobart AM15 ML-130038 dishwasher. Wash cycle does not start automatically after the water level activates the level switch & energizes the contactor? To get the wash cycle to start you need to open and close the door.


... Dishwashers

When I start the wash cycle it does not get any water, but will continue through the entire cycle. I have checked and replaced the water valve, check teh float and float switch. The handle is working correctly. The selector panel is all elcetronic and I do not know what else to do to trouble shoot. Any help??/


I would first check the water valve is it turne on? then are you getting power to the water valve ? if not problem might be in electronic panel. ... Dishwashers

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

I have a Whirlpool which just recently started leaking from the door occasionally and it is most unpredictable. It eventually stops, but before it does it will deposit about a pint of water. I have replaced the float and the float switch, thinking those were the cheapest parts and perhaps the switch was faulty and letting too much water in. That did not work. When this happens I checked the exhaust and hot steam is coming out. Could it be the water inlet valve? If the seal was bad I am ass


Hi\015\012\015\012The issue is with the water inlet valve that is bad and\015\012should be replaced. I believe everything else is working fine. Hope this\015\012helps...please post back for further assistance.\015\012\015\012Dani ... Dishwashers

Over the past two years, the machine has occasionally stopped in mid cycle, while the pump continues to run, but the cycle stops advancing. Each time there has been water in the plastic pan under the pump, valves, and other mechanisms. The float switch has been tripped, stopping the cycle. Occasionally. but not always, the pump inlet has been partially obstructed by food waste. After bailing out the pan, the machine will run normally for weeks or months. There is no indication of a leak into th


Please post the exact make & model # so we can be more exact.\015\012THanks!! ... Dishwashers

WHEM I START MY IGNIS DISHWASHER IT STARTS TO FILL THEN FROM THE RIGHT HAND CORNER CLEAN WATER STARTS TO LEAK OUT . I LOOKED AT THE DOOR SEALS AND THEY SEEM FINE I HAVE ALSO PUT IN A NEW FLOAT SWITCH AND STILL THE SAME PROBLEM ! COULD IT BE THE INLET VALVE ? HELP THANKS MANDY


It sounds like it overfilling,it may be a preesure switch problem.if you turn the dishwasher off the valve should stop if it doesnt then its the valvle.you may have to try cleaning the sunp under the filter.it may be clogged with sludge stopping the ... Dishwashers

I have a Kenmore model 587.1610 dishwasher that doesn't fill all the way when starting a load. I checked the float switch and it is working fine. The fill soleniod is also working fine and is clean. It just seems to time out before it fills all the way.also to compound the problem it doesn't seem to want to start all the wash cycle even after I have re-started the machine and it has filled to capacity. please help thanks Danny


... Dishwashers

Own a KitchenAid dishwasher, model KDC-21AD. Unit stopped shortly after startup cycle began. When cycling thru the various wash cycles, I hear a slight hum when selector switch is at the "pots/pan" selection. About 2" of water is standing in base of dishwasher and it will not start. Checked the KitchenAid site and they do not list my dishwatcher. Would like to be able to repair myself or have it done at reasonable price.


... KitchenAid Dishwashers

I have a Kenmore Model 665.15955792 dishwasher. Water is leaking out the bottom of the door. I changed the door seal and the defusers but it continued. I took off the front of the door and I see the water filling into the base of the machine. When the dishwasher starts the cleam cycle, water is pushed up into the small square holes in the bottom of the door and then splashes up over the lip of the door and out onto the floor. It has never done this before, just started recently. I have had the d


... Kenmore Dishwashers

After it cycles I open up dishwasher and the soap tray is open with soap leaking out and on dishes. How can I tell if this is a problem with float switch or water inlet valve because I think it's not getting any water? have maytag MDB3700AWE. also checked to make sure nothing stuck in float.


Try this link it should help http://appliancehelponline.com/dishfloatwaterinletvideo.html ... Maytag 24 in. MDB4600A Built-in Dishwasher

Hi there, we have had our dishlex 300 dishwasher switched off for a while and today I turned it on. I started a cycle and it stopped after a few minutes and then the Eco button started flashing. I opened the dishwasher to find it full of water and leaking out of the button. Please help! Regards, Pania


Hi just read your posting.Now the reason these dishwashers flash ECO is because there is either water in the bottom tray or your drain pump is open circuit.Is the machine making a pumping noise when it is flashing the ECO light,or is it completely si ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1790 seconds