Having problems with your Dishwashers ?

I have a 6 month old CMA UC65E commercial dishwasher. It is stuck in wash mode. I think the green start switch is bad. Is there a way to bypass the start switch until Monday?

Answers :

Try unplugging it for a few hours. In the meantime of it being unplugged, press and hold the start switch for 5 full long seconds. Then wait half hour more and plug it back in. This should reset the system
To bypass any switch, you just touch the wires together
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a 6 month old CMA UC65E commercial dishwasher. It is stuck in wash mode. I think the green start switch is bad. Is there a way to bypass the start switch until Monday?

Try unplugging it for a few hours. In the meantime of it being unplugged, press and hold the start switch for 5 full long seconds. Then wait half hour more and plug it back in. This should reset the systemTo bypass any switch, you just touch t ... Dishwashers

Have a 6 month old UC65E. Machine continues to run. I think the green start switch may be bad. Is there a way to bypass the switch until Monday?


I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo

So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

I have a Whirlpool which just recently started leaking from the door occasionally and it is most unpredictable. It eventually stops, but before it does it will deposit about a pint of water. I have replaced the float and the float switch, thinking those were the cheapest parts and perhaps the switch was faulty and letting too much water in. That did not work. When this happens I checked the exhaust and hot steam is coming out. Could it be the water inlet valve? If the seal was bad I am ass

Hi\015\012\015\012The issue is with the water inlet valve that is bad and\015\012should be replaced. I believe everything else is working fine. Hope this\015\012helps...please post back for further assistance.\015\012\015\012Dani ... Dishwashers

Good afternoon, I have a miele dishwasher model G685SC. It's old but a good machine. It has a fault code of three dashes ( ie:- - - ) and will not start. I have tried switching on and off but it doesn't clear. Is there a reset available or a way of fixing this. I think mechanically it is ok. Thank you

... Miele Dishwashers

Whirlpool Dishwasher ADG 450. Start as normal and it keeps intermittentlly stopping and starting. Washs / drains fine, but sometimes cycle seams to last for a couple of hours. I think it is four beeps when it is stopping and then immediately starts again. We had a problem months ago where as the sink was draining into the dishwasher out pipe, so dishwasher wasn't draining / filling up. Fixed the problem by turning the pipe the other way so water couldn't flow that way - but I don't know if that

... Dishwashers

We've got Beko DE 2542 FW Slimline dishwasher. Everything switches on as it is supposed to but nothing happens. Rinse aid and Salt indicator red light is not on, because we've filled them up. Switched on dishwasher, green light for "On" comes on. Selected programme level, pressed start. Green light comes on for "Wash" Nothing happens - we've left it overnight but nothing happens. What seems to be the problem? Look forward to hearing the solution.

... Beko DE2541FW 18 in. Portable Dishwasher

Low Pressure with no hose attached, pressure is good, attach hose without wand and pressure drops 50%. Have had pump apart 10 times, have checked bypass valve, have even removed bypass and filled passage way so water could not bypass wihout any change. Am down to thinking pump casting is cracked allowing bypassing to happen. Does each of the three piston chambers have a check valve so one piston is not pumping back into another piston chamber?

I worked at a tool rental while attending college and had the opportunity to work on a variety of pressure washers, however, they were of the commercial type. Commercial washers are slightly different in that they usually have seperated components fo ... Karcher 2500 PSI Pressure Washer

With Kitchaid dishwasher KUDS01FL, it wont run. All control buttons seem to work (by lighting up when pressed) except "start". When press "start", it doesn't blink or start. Does this indicate a bad start button switch or something else? Is this something I can replace? Thanks.

Hi Thanks for using FixYa. To resolve this you will have to reset the console. Do this by closing the door and press these buttons in sequence...-high temp wash - ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a maytag dishwasher mdb5601awb. when I hit the start button nothing happens. I have found the instructions to do a manual test which is hitting the heated dry button 5 times and then the start button. Thinking it will run some test which I have no idea what to look for, it actually runs the machine's wash cycles and clean, dries and tells me it clean with the green light goes on. How do I reset/reboot the machine so it starts by just hitting the start button again?

... Maytag Dishwashers

We have a Whirlpool ADG 7560 dishwasher which has recently started playing up. When switched on for a normal wash, after a short time the machine starts to beep. If you open the door the green programme light is on the pre rinse and the start light is flashing. After starting the cycle the few times eventually it works normally. Have cleaned all the filters etc.

... Dishwashers

Ariston LSI 41 dish washer had intermitant problem of green light not coming on when main power switch turned on and machine not working, the circuit had beed repair before. I played around and got the machine to go through a full circle once then would not go again. So I have put a new circuit board with switch etc. still the switch panel light dose not come on, i found bad connection in connector which comes from small plug on circuit board, (two red wires )I have checked for power to board. W

... Ariston Technologies Dishwashers

I have a Kenmore model 587.1610 dishwasher that doesn't fill all the way when starting a load. I checked the float switch and it is working fine. The fill soleniod is also working fine and is clean. It just seems to time out before it fills all the way.also to compound the problem it doesn't seem to want to start all the wash cycle even after I have re-started the machine and it has filled to capacity. please help thanks Danny

... Dishwashers

Model KUDS30FXSSO, Unit attempts to start. Blue light on the front of the door comes on indicating the cycle is starting. Pump runs a few seconds as normal. Then the maching sounds like it trying to start the next step three or four times. The blue light goes out. The washing cycle then switches to cancel/drain, ( I opened the door to see which control lights were on.) runs the drain pump then stops. The green light on the front panel does not come on indicating the cycle was completed.

... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Program stops When the machine is switched on it runs for a minuite or so then stops and bleeps and shows blanks - - - - I switch it off and again re-start and it again repeats this as above the filters have been cleaned and the water was drained and again it persists, the machine is 3 yrs old. I tried a sequence described as switching the programm button in 4 quick times but this didnt work either. Is there any other way we can re-programe this dishwasher or is it that there is a fault where so

... Smeg 18 in. DWD409SS Built-in Dishwasher

Our 2 drawer Fisher and Paykel dishwasher is automatically starting its own washing cycle (well, motor starts, but no water appears to be entering), then it shows F1 error message and a spanner icon flashes. Within 30 secs of this occurring on one drawer, this starts on the other drawer. Only way to stop is to switch off at power socket. Any idea what the error message is telling me?

... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Hi there, Just moved in to a new place and loaded up this dishwasher. First set it to "normal wash", dry "off", "start". Made noises but after a couple of minutes I heard no water and think I smelled the beginning of something overheating. Think I checked to see if the water was turned on under the sink (turned all the way to the right?). Still nothing but noise. What do you think? Lorraine

Lorraine.. It sounds like the water valve under the washer is stuck or maybe partially shorted. It is a solenoid coil activated shut off valve. The coil may be overheating, and valve not opening.. so motor is running dry. \012If you want to ta ... GE Nautilus 24" Built-in Dishwasher

I wanted to heat up a cup of tea. As I've done many times before, I pressed Time, then 1:20 seconds, then I pressed Auto Start, but fear I may have touched the button below it, which says Start in small red print. The oven wouldn't switch on, and I noticed a small green u-shaped mark had appeared at the base of the 1: I pressed Clear, and repeated my movements, making sure this time that I pressed Auto Start. Again, nothing happened. I've cleared the touchpad several times, but the oven won't

... Danby 22 in. DDW399 Free-standing Dishwasher

I have a whirlpool adp6600 dishwasher. the green light just keeps flashing (i think it's 7 times in a row each sequence) and the cycle won't start. have tried turning it off at the wall, clean

Dishwasher is in fault mode hold start/pause button for a few seconds this will reset the unit run your cycle again if dishwasher faults again call you local service man.good luck ... Whirlpool Dishwashers

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?

... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My CDA CW497 has developed problem. When i select a program say 70 degrees and press the start button and close the door the dishwasher starts in the the normal way bit after about 15 seconds the dishwasher stops making any noise and beeps once. When I open the door the green on/off light intermittently flashes. Any thoughts what the problem is please?

... Dishwashers

Dishwasher will not start when pressing the start button. Timer light flashed numbers and went off. None of the lights and buttons work. Circuit breaker in electrical panel is working. Does the on/off switch need replacing, or is it possible a mini circuit board is bad? Dishwasher installed in 2000 and is used on the average once per week.

As it is nearly 10 years old i would suggest you replacing the circuit board. To test exactly we would need the help of an continuity tester and multimeter. ... Bosch 24 in. SHU53 Built-in Dishwasher

Hi, I have a Fagor 1VF-453IT dishwasher and one day I switched it on - it did nothing else but all the red LEDs (5, I think) started to flash. And that's it, it doesn't run. No idea why, but I'd appreciate a hint before calling a mechanic or starting spending huge amounts for parts and repairs. Any chance for a reset or something? Thanks a lot!

... Dishwashers

How do i turn on the water for my washer?I just moved in to my place, tried to start the washer but it started spinning before any water came in. I think the water must be switched off. There are two taps opening pipes going into the washer, a blue and a white one. Should I try opening one of these?

Yes open both of them they are the feed lines for the washer ... Dishwashers

Hi my hobsrt amx-70 doesnt fill with water automaticaly but when i switch it to wash mode the motor starts so i think the washer thinks it is full oe water-help

Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the l ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1361 seconds