Having problems with your Dishwashers ?

High pitch electrical sound and silver spray bar under bottom dish rack doesn't appear to be rotating on wash cycle; also 2 inch round washer under where arm screws in disk has broken, could this be it?


Answers :

I would replace the lower wash arm hub and mounting components and check the silver arm for debris plugging the wash water spray holes while its off to replace the hub
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

High pitch electrical sound and silver spray bar under bottom dish rack doesn't appear to be rotating on wash cycle; also 2 inch round washer under where arm screws in disk has broken, could this be it?


I would replace the lower wash arm hub and mounting components and check the silver arm for debris plugging the wash water spray holes while its off to replace the hub ... Dishwashers

The spray arm, above the top rack, keeps unscrewing during the wash cycle. Just the arm comes off leaving a round plastic part attached to the top. This can be unscrewed and inside is a white 'washer'. The arm can be clipped back but comes off again in the next wash. The plastic 'washer' has to be turned over to allow re-attachment. Is a washer missing from inside?


Could the arm be mounted upside down and rotating the wrong way? Just an idea... Some of these can fit either way and the retainer will fit either side of the arm. ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

The disk washer doesn't drain at the end of the rinse cycle. There is a humming sound but no water is forced through the hose to the sink/garbabe disposal. At the end of the wash, there is a large amount of dirty water in the bottom of the washer. I removed the spray arms, the spray arm holder and the screen and then removed the water, and found a couple of pieces of plastic. But I don't see how I can remove additional parts from the washer bottom. What could the problem be? Is there a fi


Is the dishwasher drain hooked to the garbage disposer? If so is it new? If so did you knockout the plug in the disposer? If so then you either have something clogging the drain or pump. Or the pump motor is bad. ... Dishwashers

My dishwasher makes a banging sound, I've checked the arm & even when the washers is empty it still makes that sound. NOW I've ALSO got a sound like a "clothes washer in spin cycle mode" also in the wash mode of my dishwasher. Do I need a service call or should I just replace it since it seems to be falling apart....it's only 2 yrs with min use


Hi,This is quite a common problem. I would be able to help you, if you could provide few more details. When did you hear the banging noise i.e when filling, start of the cycle, mid cycle or it is always there?Thanks!! ... GE 24 in. Profile PDW7800 Built-in Dishwasher

- the dishes and glassware on the top rack are not coming out clean - I checked the course strainer to see if it is being blocked but don't see any thing there - I also took out the spray arm that sprays up into the top rack and ran water through it with a hose - it also appears to be free of clogs. - I don't see the spray arm spinning when I open the door during the wash cycle - - lastly, it may be unrelated, but the dishes are not coming out of the washer as hot as they used to be any i


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

The dishes in my dishwasher are not getting clean, particularly on the upper rack. It seems to be because the upper water arms are not spinning during the wash cycle. The bottom spin arm is working fine. I have cleaned out both upper arms as best as I could without removing them (above and attached below to the upper rack), as it does not appear that these arms are easily detachable. I am thinking maybe water is not making it up the line to the upper arms? I also have a lot of dirt in the b


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. First of all please check the\015\012Water temperature by using a thermometer inside the dishwasher to measure ... GE Dishwashers

Bosch dishwasher model SHV66A. New in 2004. Has worked well since then, but for last couple weeks something's up. Dishes aren't clean. Residue remains on everything. Food looks caked on & dried to plates. Silverware a little better but not much. Tried running a couple cycles with vinegar, no help. Took out strainers, etc. on bottom of washer & cleaned out; no help. Just ran a cycle now - - opened midway and it appeared the arms were both spinning. Also, water seemed warm (maybe not super


Hi\015\012\015\012If you are observing that the dishes are\015\012not clean, then you'll need to follow certain steps to be sure where exactly\015\012the issue. First thing to check for is\015\012the deter ... Bosch Dishwashers

My last rinse cycle did not completely drain. I have about 1 inch or so of water in the bottom of my dishwasher. I tried to restart the washer, but it will not turn on. I looked for some type of "restart" button, but could not find. My washer is not 4 months old.


... KitchenAid KUDS301V Dishwasher

I have a KitchenAid dishwasher KUDS01FLB6. The center wash arm assembly keeps falling off during the wash cycle. Two questions: 1. should the water release slots on the wash arm assembly be facing up toward the ceiling of the washer, or down toward the dishes? 2. why would the assembly keep coming loose - could the plastic connection be worn?


Yes the connection is worn or even brokenPlease rate/vote this response thanks ... Dishwashers

Dishwasher just started leaving food residue on dishes after washing. We usually don't rinse beforehand but even when we do this it's still happening. Can I run something thru a cycle to give the washer a good clean out? I've cleaned the filter (nothing there), tried to clean the spinning arm as well as I could and looked for any other food that might be clogging things up. Dishwasher came house - think it's about 6-8 years old. Otherwise works great.


Hi,The scum, film and white residue problems have started since the reduction of phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your ... GE Nautilus 24" Built-in Dishwasher

Noisey maytag We have a maytag quiet series 300 with the 3 racks. Just recently we have been hearing alot of noise from our dishwasher while it is in the washing and rinsing mode. We have checked the arms to make sure they are moving but doesn't seem to be a problem. Thought maybe there is a liquid that we could pour into the washer to run through it's cycle? Of course we know nothing about the inter works of a dishwasher.


Hi, i had the same problem twice and both time there was some plastic stuff in the shredder. Remove the screw in the middle and remove the cap and you will probably find some pieces near the blades. ... Maytag 24 in. MDB5651A Built-in Dishwasher

Lg adora model no.ghda696pss serial no.sr800098c dishwasher takes in water but no washer arms are going round and the soap container does not open at the end of the cycle the dishwasher empties and heats the utencils which have not been washed.


Hi.Ensure that there is water getting inside the machine. If there is no water, then the water level switch or the water valve may be defective. The door lock switch must also be tested.If there is no water getting into the ap ... LG Dishwashers

All of a sudden, my dishes are not coming out as clean, especially the top rack of glasses. They have a white film on them.. I changed the detergent and that didn't help. We have lived here for 20 years and have had this dishwasher over 3 years? I feel as if the upper arm is not rotating during the cycle. Could this be broken?


There are many probable causes of failure .A dishwasher's water inlet valve is its most common part to fail. When \015\012your dishes are not being fully cleaned, quite often a faulty water \015\012inle ... Frigidaire PLD2855RFC Dishwasher

My dishwasher is not cleaning dishes... The cycles work but the dishes do not get clean an sometimes are more dirty if that is possible. I have tried adding jet dry and extra cleaning liquid but get no results. Also there are times that the bottom of the washer fills with water unexpectedly and will even leak on to the floor. It doesn't leak when the dishwasher is running... I just don't know what to do other than clean out the spray arms. Please help.


Best off to call a certified repair company such as Sears. ... Kenmore 15899 Built-in Dishwasher

My dishwasher is not cleaning dishes... The cycles work but the dishes do not get clean an sometimes are more dirty if that is possible. I have tried adding jet dry and extra cleaning liquid but get no results. also there are times that the bottom of the washer fills with water unexpectedly and will even leak on to the floor. It doesn't leak when the dishwasher is running... I just don't know what to do other than clean out the spray arms. Please help.


Hi,Check your heating element.. Dishwasher ... Kenmore 15899 Built-in Dishwasher

I have a Kitchenaide dishwasher which, when all the cycles have run, there is about 1 inch of water left in the bottom of the washer. what could be the problem and how do I fix it?


... KitchenAid KUDR25 Dishwasher

The spring loaded catch that locks the flap on the rinse aid compartment has broken on my dishwasher, this coincided with the tablet not being dissolved as the washer went through its cycle. is this connected or a seperate issue? Also can it be repaired or is a new machine needed.The model is Whirlpool ADG722


The catch should be replaceable. \015\012The timing is most likely coincidence. ... Dishwashers

Tub leaks, with a partially filled tub (2.5 inches measured from the lowest point over the pump assembly.) Promblem occured after the washer was idle for 3 weeks. Have just replaced the main water inlet valve. The fill tube is not the source of the leak, the top arm feed is fine also.


I am assuming leaking when it is running, not sitting idle. Leaking from the door? Fill and run unit for 1 minute with no detergent. Open door. Are suds present? Suds turn into water when they drop to the floor. Suds can flow over the lip of the tub ... Maytag MDB7100AWB Dishwasher

GE Dish Washer GSD 2800 DO3 runs a partial cycle...(even empty) and then beep and gives a message on control panel "washer arm blocked". Even ran without dish rack in washer still got the message. Push reset button and washer starts back runs a couple minutes and then stops and then beep and gives the same message on control panel "washer arm blocked" again. There is "NOTHING BLOCKING" the washer arm!


The rotating arm has a magnet in it to let the controls know if it is turning. Yours is not turning so \012\012\012\012check the jets for blockages... you might have to remove the arm to clean them properly ... Dishwashers

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

I have a Bosch dishwasher, stainless steel front- with buttons on the inside top( same as display, and the washing cycle won't start. Water seems to be running into the washer, as I can hear it, but the cycle never starts. Recently, I had clogged garbage disposer issue that has been resolved. The dish washer drains into the disposer, and I had free standing water left behind in the washer for 2days during this time.. Could this be the issue? Can you help me figure out this problem? Thanks!!


... Bosch 23 in. SHU 8805 Built-in Dishwasher

I have a De Dietrich DV640JE1 built in 45cm Dishwasher, working fine for over 3 years. After replacing the connection under the sink to fix a leak it has stopped working. But I dont think this is related. I run a cycle and it fills water in the bottom of the machine, it drains it out in the end but the 2 arms are not rotating and no water comes out. I checked the arms and they are not blocked. A faint clunking sound can be heard at some part of the cycle. I did also run a cycle with the dr


Hello Benny,\015\012\015\012It's highly unlikely that replacing the connection under the sink is related to this problem.\015\012\015\012From the symptoms you describe, it's almost certain that the circulation pump motor has f ... Dishwashers

Hi there I have a Bosch SGV4313GB/17 Dishwasher the problem is there insuffient water pressure to feed the washer arm and they are not rotating Ihave cleaned the arms and circulation pump impeller with white vinegar ,I have also overriden the door switch and operated the dishwasher with arms removed and the circulation pump seem to be working but with insuffient pressure also the machine does not fill to the depth it did when it was fine! How does one tell if it is the impeller or the


Ours is a SHU3300UC/06 model, basic model which we bought in 1999 so have had 9 years of trouble free service.Recently\015\012we noticed that there was soap left in the soap dispenser after the\015\012machine had finished all the cycles. On fu ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1786 seconds