Having problems with your Dishwashers ?

I have a kenmore dishwasher. Model 665.13793K601. The unit will not swith out of the wash cycle. Runs continuosly in wash cycle. will not advance to drain and dry.


Answers :

Hi. This is a simple control fault that may be resolved by unplugging the unit for five minutes. This is called a hard reset. The hard reset will DE-energize the unit and reset the core logic sector for the control board. Now, if the unit continues to become suspended in the wash cycle, after the hard reset, this will confirm the apparent damage that will require yo to have the affected part replaced. The correct part number for your replacement Control board will be W10084141

Replace the main control board if the hard rest fails to correct the issue at hand.


Hi
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks for using FixYa. If the\015\012cycle doesn't complete, check these:
\015\012\015\012Water-heating\015\012cycle
\015\012\015\012Many dishwashers heat the wash\015\012and/or rinse water to a higher temperature, as the cycle calls for it. In these\015\012cycles, the dishwasher pauses after it has filled with water, waiting for the\015\012water to reach the pre-set temperature. What happens next depends, as follows:
\015\012\015\012
\015\012\015\012On some units, the pause is timed\015\012and the unit continues after the allotted time.
\015\012\015\012
\015\012\015\012On others, the cycle can't\015\012continue until the water reaches the higher temperature. If you have this type\015\012of dishwasher and the water isn't being heated (say, because of a problem with\015\012the heating element or thermostat), after the unit stops at the heating cycle,\015\012it never continues. When you repair the heating-system problem, the "cycle\015\012problem" is fixed too.
\015\012\015\012
\015\012\015\012Timer
\015\012\015\012Timers don't often fail. But if\015\012every other part of the dishwasher seems to be working properly and the timer\015\012knob seems to be stuck in one place--doing one function continuously--the timer\015\012may be at fault. Dishwasher timers can't be repaired. If yours is defective,\015\012replace it.
\015\012\015\012
\015\012\015\012
\015\012\015\012Please do accept the solution\015\012if the issue is resolved or else revert for further assistance.
\015\012\015\012


\015\012\015\012Thanks
\015\012\015\012Rylee
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a kenmore dishwasher. Model 665.13793K601. The unit will not swith out of the wash cycle. Runs continuosly in wash cycle. will not advance to drain and dry.


Hi. This is a simple control fault that may be resolved by unplugging the unit for five minutes. This is called a hard reset. The hard reset will DE-energize the unit and reset the core logic sector for the control board. Now, if the unit continues t ... Dishwashers

Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.


This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher

I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one


... Ariston Technologies Dishwashers

Kenmore Elite dishwasher Model #665 1597 2992 Machine fills with water but thereafter it neither washes nor drains. Machine will not drain when I advance the cycle by pressing the Cancel/Drain button. There was a report that there was some noise when the machine first failed. I do not hear anything when I try to run a cycle. What might the problem be? How does one turn the motor manually to see if it is bound up by something? If it is the motor do I want to pay an extra $70 to $100 and


... Dishwashers

All of a sudden, my Kenmore dishwasher (Model 363.1411691) will not cycle. When I lock it shut and try to set it to wash, all I hear is a click--no motor running, no water sounds. As I advance the timer knob, I just get clicks where each cycle should begin. There is standing water in the bottom of the dishwasher which does not drain out. Any advice would be much appreciated, for sure.


Hi.The clicks are simply the relays in the timer board that try switching on. The control module is likely working.The cycle does not start because of a different problem.If no light is coming on, then ensure that wall socket ... Dishwashers

Leaking dishwasher There is standing water in the dishwasher when it's not being used. Recently we had a garbage disposal installed and was wondering whether this may cause the water from the sink to settle in the dishwasher. Also, the water rises and leaks on the floor. We have to run a wash cycle to drain and dry out the dishwasher. What do you think the problem is?


It sound like while the assembly of the garbage disposal, you placed the end of the drain line pipe in a lower position than it was before.\015\012Good luck! ... Kenmore 15129 Built-in Dishwasher

Dishwasher runs forever - I have to manually drain it by pushing 2 buttons on front at same time - never gets to dry cycle - makes no difference what wash cycle i am in - however the rinse & hold cycle seems to work


Hello,Welcome to FixYa ... Thermador DWU244 Dishwasher

I have a Kenmore Elite Dishwasher, Model # 665.13119K701 that is just over a year old. It does not cycle through the washing/rinsing/heated dry cycles. It continually runs in the ''washing'' mode. It only drains if i press ''cancel/drain''.


Replace this: ... Kenmore Dishwashers

Kudco21rbl2 model Dishwasher continues to run in the wash cycle, it will not advance to the rinse or dry cycle.


Our kudco3fv550 continues to blink start/resume. It will not start\015\012please advise ... KitchenAid KUDC02IRB Dishwasher

My dishwasher won't drain. It runs through the whole wash and dry cycle...and when I open it to unload the dishes the bottom is filled with standing water. None of the lines that I can see appear to be kinked, and I'm not sure what else to check. I inistalled the dishwasher myself becasue my husband was working out of town...this was about a year ago. Haven't had any problems with it until now. Thanks for any help or suggestions you're able to offer. Christine Fitzpatrick


If you hear the drain pump run after wash and rinse cycles then it is likely the problem is in the kitchen drain end. Have you got a disposal unit in the kitchen sink. Sometime it is full and causing a block.\015\012\015\012If you don't h ... Dishwashers

My dishwasher skips the final drain cycle. The lines are all clean and there is no clog. It drains just fine in the beginning of the wash cycle. Every time I do a load of dishes I have to run the full cycle, then leave the machine open for 3-4 hours and start the cycle again and listen for the drain at the beginning of the wash to drain the machine from the initial wash and stop the machine after it is done draining so it won't fill up again. Sometimes we have to unplug it and wait about an hour


... GE Nautilus 24" Built-in Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

Bosch dishwasher My Bosch dishwasher finished a wash cycle and was showing the "END" light on, however, the motor was still running as though it was stuck on the drain cycle (there is a gurgling sound from where the eater drains off beneath the filter. Subsequently turning the washer on just repeats the apparent drain cycle with a constant gurgling sound (it does not kick into wash mode). The number on the manual is & 258 (7705).


Is all the water draining from the tub? if not the pressure switch will not reset and it will continue to try and clear it self...check drainage system.\015\0122. pressure switch is jammed on..build up in the sensing chamber..commo ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!!


The Timer might not be bad. If one of the two thermostats is bad, the Dishwasher will exibit the same symptom. The thermostats are 141 deg. F and 161 deg F.They only cost $20 each. The Control Module is close to $200. ... Bosch SHU4006 Dishwasher

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

My Maytag Dishwasher mdbd880awq wont finish a wash cycle. It will wash and rise then when there is 32 minutes left it wont drain and wont dry the dishes, It just makes a clicking sound. I have to dry the dishes by hand and then use the rise only cycle to get the tub to drain. The drain only doesn't work either


... Dishwashers

My 2008 frigidaire 24" dishwasher model #FDB1050REC is not washing during the cycle. I have run the test cycle and the tub is filling up and draining but no washing is taking place during the wash cycle. The dishwasher has an electronic control board and therfore no mechanical timer. I put test leads to check for voltage on the power leads to the main washing pump, which I have already replaced with a new one, and I'm only registering a low voltage of around 10 or 11 VAC. With the cycle off I'm


If you have replace the motor and this did not fix your problem then yes replace the control board ... Dishwashers

Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?


... Dishwashers

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

Dishwasher works fine except that after the drying cycle, water slowly builds up in the bottom of the dishwasher. It did this a few years ago for several months, but then it stopped doing it altogether. I did nothing to fix it. Now it's started doing it again. I run the dial around to a point where it drains, let the water drain and then turn it back to off before the drying cycle begins.


Hello,\015\012\015\012This would mean that the dishwashers water valve has failed. This is a simple repair to make yourself. The lower access panel would need to be removed, four screws. You can purchase the part from the link below.\015\012 ... GE Dishwashers

We have a n eight year old fully integrated asko dishwasher. Only the rinse cycle works, so I rinse many times - last rinse with detergent and then run the short program which does not wash, but will dry the dishes. The circuit board was replaced once before under warranty($500.00 labour) and I suspect that we may have to do the same again. Can we find this on the internet and do it ourselves; we have good electrical knowledge. Thank you in advance.


This is most likely an issue with the timer. Timers\015\012don't often fail. But if every other part of the dishwasher seems to be\015\012working properly and the timer knob seems to be stuck in one\015\012place--doing one function continuously--the ... Asko Dishwashers

Yes I have a whirlpool DU1345XTVB1 dishwasher. Just got in July. After each wash cycle the dishes are not dry. I have been using Finish gelpacs w/jetdry & also have a off brand drying agent in reservior to help dry dishes. The water temperature is set pretty hot & washer is draining good. I have tried checking wash cycle a few minutes into 1st cycle to see if water is in filling & heating. Didn't know if maybe heating element going out or thermostat not working? Thank you for your time.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers

Ref: NEFF Dishwasher S5555XOGB/70 (FD No. 8602) Problem: Does not drain at end of wash cycle. Checks/Symptoms: 1. No blockage in whole of drainage system, system and filters are clean. 2. Pump does operate mid wash cycle ? drainage tube can be felt pulsing and pipe gets warm right through to the main drain connection at the ?U? bend. 3. At end of wash cycle the pump appears to still be trying to run but there is no flow, even when the door is opened. If machine is emptied by hand the pum


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2770 seconds