Having problems with your Dishwashers ?

The dishwasher will not start. It had been running, I opened the door and then closed it and that was it.


Answers :

Cycle the power at your circuit breaker to attempt to reset it.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cranky dishwasher I have to admit my wife's solution is the only one that works. Our ten-year-old Superba built-in usually starts a normal cycle part-way through, at the wash part, without filling or opening the dispenser door. Therefore the dishes come out with the soil now baked on. Closing the door, selecting normal and start results in a pump-out sound, or at least just the pump running to wash the dishes. The dishwasher ignores any cancel button push,and the light does not come on over t


You want to make sure that the dishwasher is level and secure first of all. Then I would look into the door latch assy. Sounds to me that you are not making all the latch switches when closing normally. When you are slamming it, you are making the s ... KitchenAid KUDS24SE Built-in Dishwasher

Hello I hope someone can help me. I have a Siemens Hydrosensor Dishwasher that when I start it up in runs for a while and shuts off. I need to open and close the door several times then it may run for a short while, 15 seconds to a couple minutes and then shut down again. Finally, it will run through the rest of the cycle. The issue generally occurs when the digital timer is between 85 and 78. If I just leave it go once it shuts down it does eventually start up and will complete the washing cycl


It sounds like the door switch is at fault, it will cause the symptoms you stated. ... Dishwashers

Hi - I have the Miele G 2470 dishwasher. It starts, and I have it set at "2 in 1 Tab" and on "Normal". I close the door and the machine makes a sound like it is starting, but then after abiut 30 seconds it starts alarm beeping and doesn't run. When you open the door it shows the light is now on next to "Intake/Drain". To stop the beeping I have to press the "off" circle. This sequence happens each time. what do you recommend to get it to work? thank you very much. Lori.


You could check into the User's Guide online manual below:http://safemanuals.com/414159.php?k=41da0c038c6dca28da72cf9056db1c61&ID=63815&q=MIELE%20G2470 ... Miele Dishwashers

Asko 1585 Dishwasher. Lately the washer has not been completing it's cycle without going into the all lights flashing mode. Usually just opening the door, closing then pushing start gets it going again. Yesterday this happened and it was restarted as described, then it go stuck in what appeared to be a drain mode - all lights flashing, drain motor running. It was in this mode for several hours and could not be stopped by any means. Pushing buttons or opening the door had no effect. Even c


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa. You are right it is related to a bad control board. The\015\012control board has gone faulty and needs a replacement. Please check this recall\015\012information--- ... Asko 24 in. 1585 Built-in Dishwasher

Maytag MDBH965AWQ I have a Maytag dishwasher model number MDBH965AWQ. A few weeks ago the clean and sanitized lights would not go off after the door had been left open for over 30 seconds. Then last week, the diswasher would shut off in mid cycle and all lights would turn off with water still in the dishwasher. Today, I noticed that I am able to open the dishwasher door while the dishwasher is running and it will continue to run like the door was never opened. Now it is starting to trip the brea


2 items in need of testing are the door switch - and the main controller board/timer unit.CLIC ... Maytag 24 in. MDBH965AW Built-in Dishwasher

My dishwasher, model # fdb1050reb1, will not start again. I started to run it and opened the door to put something else in and when I closed it back it wouldn't do anything, the start light just flashes.


You may have already, but try opening and closing the door and restarting the machine again. If the door switch is loose, you may be able to get it to make the connection and run. If it just palain won't work that way for you, you'll have to try to ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

The dishwasher has the normal and economy wash lights flashing and after we hold the start button down for 4 seconds the stop and then return to flashing? The washer motor runs when the door is closed and no water comes out and the system doens't stop trunning until the door is opened. The system ran for over 4 hours yesterday. Viking Professional


Hello, welcome to ... Viking 24 in. Professional Series VUD040 Stainless Steel (Premium) Built-in Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

Bosch SHX46A (6 years old) Selected regular cycle, pressed On and closed door. Cycle did not start normally. Pump runs, but no water is coming into the DW. I confirmed the water supply line is turned on. I opened door, turned off On/Off switch, then poured water into drain. Then turned On/Off switch on. DW began pumping water OUT of the DW. Also, it doesn't matter if the door is open or closed - if you turn the DW on, the pump will run. I suspect a problem with the electrical controls, or perha


From your description, I doubt that the problem is door latch is the cause.\015\012\015\012The first thing that a modern dishwasher does before it begins to fill with water is run the drain pump.  It appears that this DW is not progressing ... Bosch Integra® 500 SHX46A0 Dishwasher

Have a Bosch shy56a05uc dishwasher that suddenly stopped working to a point. I believe it is related to the door latch switch, because I don't feel the door securely latch shut when I close it, and I also don't get any cycle lights or times registered on the LED readout. If I depress the on switch, the drain pump will start even with the door open, and, depending on how long I leave the switch on, water will start to fill in the dishwasher, open or not.


Does your dishwasher electronic control or mechanical timer? if mechanical timer, I encounter a similar problem n change the mechanical timer. that problem solved.\015\012\015\012Prince P ... Dishwashers

My Frigidaire fghd2433kf1 starting flashing PF occasionally. I would open and close the door and it would go away. It became more frequent until two days ago when the dishwasher stopped mid cycle and flashed PF. When I opened and closed the door, everything went dead and the dishwasher no longer works. It acts like it has no power coming into it. I checked the breakers and the wires connecting the power into the dishwasher. No luck. I replaced the control panel, but not the control board. It did


... Frigidaire FGHD2433KF Builtin Dishwasher

Close the Maytag dishwasher, cycle starts, but I noticed a leak! Dishwasher door can be opened by putting your fingers on the edge and pulling it open. Tried it again, door clicked, thought it was ok but still could open door with fingers. Emptied the washer, door locked. Put in a few dishes, same problem


Your problem appear to me like it come from your upper basket .\015\012pleas try 1st to ensure the basket goes inside\015\012untill the end it is important..\015\012 thank you ... GE Dishwashers

Water will not drain out. do not have a drain airGap. when opened dishwasher this afternoon still had water in the bottom of it. Emptied the dishes, closed the door, pushed cancel/drain. the green light came on and i could hear the dishwasher running but not hear the water draining out. Let it run the 2 minute cycle for cancel/drain opened the door and the water is still there.


Hi,Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Waterwill not drain out ... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

The dishwasher will not start. It had been running, I opened the door and then closed it and that was it.


Cycle the power at your circuit breaker to attempt to reset it. ... Dishwashers

My Maytag dishwasher runs part of the cycle,then stops. If I open the door and close it later it will start up again.


... Maytag 24 in. MDB3700 Built-in Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have a bosch SHU8815UC dishwasher. It was already installed when i moved into my apartment - so I'm unsure of the age. The dishwasher isn't functioning. When I open the door, the "Clean" light and the PowerScrub button are red. When i close the door, the light go off but nothing happens. One time I closed the door, it started to rev up but would shut off and beep three times after about 1 min. No water comes out. Any ideas? Thanks! June


... Dishwashers

Viking dishwasher, after pressing normal cycle button, then the start button, the dishwasher begins to run (doesn't seem like there's water enters), then it runs for about 5' and shuts off by itself, the entire cycle is about 5-10min. When I open the dishwasher, it seems dry and the dish detergent door didn't open at all. What should I do to correct this or where do I troubleshoot?


... KitchenAid 24 in. KUDI01TJ - Multiple Color Built-in Dishwasher

Myy kitchenaid dishwasher model kudi01flss doesn't start even though the lights on the panel light up so I opened up the door to look at the latch and found a broken plastic piece that appears to be part of the latch. Could this be why the machine doesn't start. The funny this is the door still seems to snap closed even with this broken piece but what I'm thinking is that this piece activates some sort of electrical connection that turns the machine on when the door is closed. Any thoughts on th


... KitchenAid KUDC25CH Dishwasher

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

My dishwasher has stopped cleaning plates properly. It makes everything wet but at the end of the cycle the detergent block is half dissolved at the bottom. I have just run a cycle and opened the door during this. The bottom is full of soap suds and water and the top spray bar is dripping water after I open the door but when I close and then reopen a few secs later the top spray bar has definetly not rotated. The water is also not hot, this dishwasher is a cold fed only machine so I guess the el


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

DISHWASHER MODEL#GLD5500L15BB WHEN D/WA IS RUNNING IT STARTS BEEPING,MUST OPEN DOOR AND RECLOSE DOOR TO START D/WA TO RUNNING AGAIN


... GE Dishwashers

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

My CDA CW497 has developed problem. When i select a program say 70 degrees and press the start button and close the door the dishwasher starts in the the normal way bit after about 15 seconds the dishwasher stops making any noise and beeps once. When I open the door the green on/off light intermittently flashes. Any thoughts what the problem is please?


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2232 seconds