Having problems with your Dishwashers ?

Water is not draining from bottom! , Sometimes it wont introduce water during the wash sequence....all valves are opened!


Answers :

Most likly you need to replace the impeller at the bottom, usually an easy fix on most dishwashers, two too four screws, remove the impeller (it has alot of fins) if these are worn or some are broken this is your problem. order from appl. parts store or sears. If the water isn't being pumped out the float valve won't allow new water in because it would oveflow.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water is not draining from bottom! , Sometimes it wont introduce water during the wash sequence....all valves are opened!


Most likly you need to replace the impeller at the bottom, usually an easy fix on most dishwashers, two too four screws, remove the impeller (it has alot of fins) if these are worn or some are broken this is your problem. order from appl. parts store ... Dishwashers

Dishlex Global 310 model. My dishwasher has water sitting on the bottom of it and it wont drain. I noticed it after I did a cycle of dirty dishes and the 'fast' light was flashing when I went to open it. Which shouldnt have been because it was on a normal wash. The water has been sitting at the bottom for 2 days now and still wont drain! I've taken out all the parts on the bottom which come out and cleaned them. Still no change however.


Just ran another cycle and it was fine ... Dishwashers

Whirlpool Quiet Wash Plus dishwasher Model DU920PFGZ3. Worked fine until I replaced the insinkerator and forgot to punch the drain plug leaving water standing on the bottom of the machine. I punched the drain opening, and pushed the cancel/drain cycle button. It drained fine but since no water comes from the spray arms. I have removed the arm all the way down..NOTHING!! Some research indicated it could be the water inlet valve. When the buttons are pushed, it cycles but no spray or water.


... Dishwashers

Water is remaining in the bottom of the washing units. I tried cleaning out the tubes with a snake via the garbage disposal. I clean the bottom of the washing unit but I think the valve is not opening to drain the water. Where can a get a repairman to look at this right away. I'm in Needham, Massachusetts. 781 223 6035. Thanks Alex


Hi,\012Here is a tip that I wrote that will help you to figure out what is going on with your garbage disposal and why it is not working. ... Fisher and Paykel 24 in. DD603H W Built-in Dishwasher

Water wont drain out of bottom of tub. The dishwasher works fine, it just wont drain the dirty water out. If I restart it to wash again, the dishes are washed in the dirty water.


Hi, A clog in the drain line or air gap (if there is one) is the usual reason that a dishwasher won't drain. Often the problem is at the point where the drain line attaches to the garbage disposer or househ ... GE Nautilus 24" Built-in Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???


Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher

I have the Siemens SL84A305UC Dishwasher. All of a sudden it stopped cleaning dishes, but everything sounds normal and it fills and drains water, and sounds like it is completing the cycle. In the past when I opened the door while it was actively washing the water would spray out aggressively. Now, when I opened it while it was supposed to be washing I see just a small amount of water coming from the bottom wash blade, and not even enough to turn the blade very far. I thought it was just a c


... Siemens 24 in. SL84A305UC Built-in Dishwasher

I have a DU8000XX6 series Kenmore dishwasher that won't drain the water properly. There is about a half inch of water in the tub and the float is raised (not sitting on tub bottom). When I lift up the float a little more I can hear the float switch make. I would assume that when the water is high enough the float switch makes and energizes a solenoid valve in the drain to drain the water, but shouldn't it stay open until all the water drains? Lifting the float while the dishwasher is off wo


... Kenmore 24 in. 15142 Built-in Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Whirlpool DU915PWPTO wont drain leaving water in the bottom what does drain is slow, disposal clear,hose clear, pump runs to wash dishes,water in bottom is more than normal


... Whirlpool Dishwashers

Kenmore dishwasher type 573-D, model 665.16034402. Items on top rack don't get washed. Items on bottom rack are washed fine. Appears top sprayer and maybe middle sprayer aren't getting water. At rear of washer, top rubber flapper valve (which feeds middle sprayer when top rack is in raised position) is stuck open, bottom flapper valve looks OK. We use top rack in raised position so this doesn't seem to be the problem.


... Kenmore Dishwashers

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

After cycle completed, opened door and found water did not drain. i removed the screen at the bottom and used wetvac to **** all the water out. i was also able to hear suction from hose to sink P trap. i'm confident there is no blockage. i attempted to run again only to find out the pump was running but, no water was filling the machine. Yes! the valves are open! two different issues? one other thing; due to the no thought behind this, the name plate was stuck to the inner part of the door whi


Possible that the drain pump needs a closer look , clean and check if the pump is working. If there is voltage to the pump during the drian then the pump is faulty.\012The second issue if the inlet chocking , check the inlet filter , check the ... Bosch SHU9915UC Dishwasher

My maytag is about 2 years old, we recently can't get the residual water after the wash to drain, so there is always water sitting in the bottom of it, it runs, cleans but wont drain all the water. what should i do?


WEll, look for restricted screens on all pump intakes, and look for kinked drain hose. Some water MUST remain in the bottom, but usually not enough to see. ... Maytag Dishwashers

My GE Nautilus DW doesn't fully drain. When it is drained as much as it will it leaves water in the sump at the rear right. If you run the pump at that point, it sucks water out of the sump, but when you open the door and the pump stops water flows back into it. It seems like there is a check valve that isn't working. I have cleaned the sump and the screen which runs accross the rear. I also have taken the plunger out and cleaned it. Then I took the housing for the plugner off the bottom. I don'


HI. check the following areas for fualts.1. Air gap / Drain hosesIf there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: I ... Dishwashers

Got a lound buzz type noise that I thought was a bad solenoid on the water valve. Tub also filled up & overflowed1 Replaced water valve ($30), but now dishwasher wont run thru cycles or fill with water to wash--seems to be stuck on drain even though digital counter counts down. What should I check next?


You may have dislocated the connection that controls the AquaStop circuit.\015\012\015\012This is linked to the inlet hose. Either the connector linking the inlet tap to the inlet valve is loose or the float switch has triggered.\01 ... Bosch 24 in. SHU53 Built-in Dishwasher

Water wont drain from the bottom, removed hose and not stopped up. float switch is working but dont know how to test the discharge valve that controls where the water goes, either out drain or back into sprayers


\012Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

My daughter put the wrong detergent in the dishwasher (!). Now its stuck in drain cycle. If I put it onto wash cycle I can hear it draining even with the door open, but when I shut the door it doesn't go to wash and the bottom fills up with water. Thanks!!!


Hi,You need to find the bottle of white vinegar or cooking oil, if you have one...that will cut the suds and get you working again...Check this out...http://www.acmehowto.com/howto/appliance/dishwasher/wrongsoap.ph ... Bosch Dishwashers

Kenmore 17369 When cycle starts... it sounds terrible (crackly sounding).... doesn't sound like the water is coming into the dishwasher. If I add water to the machine during a rinse cycle...it will wash and drain on its own.... Then I hit cancel. Please help.. I can't locate the owners manual.. Do you know where I can get one.. I understand that you can open the bottom up and see if there is anything lodged in the bottom of the dishwasher. Please help! thanks Cheryl


The problem is your water inlet valve. If you remove the panel at the bottom of the dishwasher you will see\015\012either a copper hard pipe, or a flexible steel hose leading into the\015\012water inlet valve.BE SURE TO CUT OF ... Kenmore 24 in. 17362 / 17364 / 17369 Built-in Dishwasher

Water will not drain from bottom of GE Profile PDW7300 dishwasher. I checked the service mode feature by depressing the cookware and the heated dry keypad simultaneously for 3 seconds and did not hear any activity from the dishwasher when I activated the drain pump and when I activated the main pump. Other service mode features did activate when I checked them (i.e. activate water valve, open active vent, etc.).


... GE 24 in. Profile PDW7800 Built-in Dishwasher

Machine cannot finish cycle and is stuck in pumping out mode. Only tiny amount of water in drain basin at bottom, no excessive water. Was set at 10pm, still attempting to drain 8am! Has no diagnostic dials or manual over rides so continues on whether door is open or closed, even if I switch off and on again. Possible related issue, recently finish at end of washes has been "grainy", far from perfect, surfaces slightly sandy feeling.


... Bosch 24 in. SGV43A03 Built-In Dishwasher

Is it common for Kitchenaid dishwashers to have water pooling inside them? It's almost like the valve for water coming in isn't shutting all the way...in the middle of the day, we'll find water inside the dishwasher...it drips out the front when you open the door...but when you turn it on, it doesn't have any problem draining the system...mysteriously, we find water in the bottom...what's up?


There is a rubber flapper valve that keeps water from running back into your dishwasher. It's a $5.00 part, but it's a bear to get to,\015\012\015\012You have to pull the drain pump to access this flapper.\015\012\015\012Also ... KitchenAid 24 in. KUDP02FRSS Stainless Steel Built-in Dishwasher

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2067 seconds