Having problems with your Dishwashers ?

Leaking from a hole in a small black rubber hose that comwes out of the wash pump


Answers :

Simple fix, replace hose with easily found replacement at most hardware stores.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Leaking from a hole in a small black rubber hose that comwes out of the wash pump


Simple fix, replace hose with easily found replacement at most hardware stores. ... Dishwashers

A rubber spatula was dropped to the bottom during the wash cycle. It melted a small hole in the bottom of the washer, and now it's leaking. Is there a way to patch the hole?


High-temperature silicon glue will probably work ok. Be sure to clean the hole with alcohol and allow 24 hours for the glue to cure. Epoxy would be a better seal, but it doesn't adhere to plastic very well. Hope this helps! ... Kenmore Dishwashers

I have a washer model 1805 (1800 PSI). Everything works but there is always leaking of water (sprays) when I use it. The leak is not from where the water hose connects to the washer, but where the black piece attached to the hose is connected to the body of the washer. I can still do a decent job of power washing, but am wondering if the leaking of water is reducing the power of the washer.


Yes, leaking water will reduce the pressure. Sounds like you need to replace the O-Ring inside the connections on the pump. This is where the pressure hose connects to the pump. If you look carefully inside that connection you will see an O-Ring. Use ... Campbell Hausfeld PW1805 1800 PSI 15 GPM Pressure Washer

Have a GU1500XTK whirpool,took apart and in the small round hole in the sump i found a small black round soild rubber disk,i dont know where it came from or where it goes..diagram only shows the other black flap.


Its the check valve. it goes in a rectegular with the round edge first. its near the hole going to the pump ... Whirlpool 24 in. GU1500XT - Multiple Color Built-in Dishwasher

E3 error I have a Fisher and Paykel DW60cdx2 dishwasher which was tripping the safety switch as the drain hose was leaking and was shorting the wash pump motor out which I replaced and now on start up I I did notice the wash pump motor had a solenoid on the side where my original did not otherwise all else is identical.


... Fisher and Paykel Dishwashers

Pump problems we have a mobile car wash service that we use in the winter months we have a 300 gal tank and several power washers.we use 3 diffrent machines [email protected] gal 2500 [email protected] and a3000psi @3.0 gal i;m having a lot of pump problems with all of these machines.a friend that he thinks that the hose that the machines feed of is to small 3/4'' he suggests i use a1 1/2 hose as close to the machine before adapting to the 3/4'' fitting right now it;s about12'' long away from the tank.any info wo


Are you only using gravity to feed the machines. The law of gravity is that, for every foot of elevation you will get 2 PSI ( pounds per square inch) of pressure. You can figure out the minimum volume that the manufacture requires and make sure that ... Comet GXD2527G Pressure Washer Pump

During installation of new dishwasher when I was attaching drain hose to pump I saw a small red rubber fap attached to end of pump discharge nozzle. Is this a backflow prevention or something to keep


It is a back flow preventer. Leave it alone and attach the drain hose. ... GE Profile PDW8400J Built-in Dishwasher

My GSD5940Do1ss leaks from what appears to be a tube that is in the middle left of the underside. There are no leaks from the hoses or pumps. It only leaks when it is adding water during the wash or rinse cycle. The part it is leaking from looks like a plastic tube that is part of the tub enclosure. There are four of them and I think they are really the mounting guides for the tub enclosure, which means the water is probably flowing down the tub to this spot. I'm assuming that means my seal arou


Other than seals, and you're sure the hoses themselves are intact, i would suggest looking at the fitting for each hose... Are these hoses PEX, or just standard plastic tubing? ... GE 24 in. GSD5940 Built-in Dishwasher

Water leak My model is a GU2400XTPB1 The tub of diswasher has small hole where a screw is mounted on bottom of dishwasher. Leak is severe during cycle. I have tried epoxy but it will only hold up for a few washes. Will anyhing seal the leak and hold up? The dishwasher is only 2 years old..


Mine also started leaking. Element also too hot. Mine has a 20 year warrenty on the tub (which I was NOT aware of) Repairman came today and the whole tub unit and element will be fixed for free! Look in your whirlpool instruction book to see if your ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Pump leaking out hole in botton of karcher presure washer. There is a small hole in both the top and bottom of the pumg. May have something to do with thermal protector reset.


... Karcher PSI Electric Pressure Washer

The wash pump is leaking, not at the larger joining o-ring seal, but through the vents in the bottom of the motor just past the blade/rotor. Is there a small o-ring inside that is on the shaft that may be leaking? Is there a schematic breakdown of this motor somewhere? I already ordered a new one, and will "play" with the old one to see if I can fix it, just looking for some direction.


The shaft seal has failed. Often the top ball bearing becomes noisy after having the water leak through it. The seal is probably a lip seal rather than an O ring. ... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

Whirlpool ADP5966 developed a leak at small rubber connection from circulation pump. Leak repaired, machine reconnected, programme selected, some sound for about 20 secs then shutdown. Display showed F6 once then nothing. L.E.D.programme indicator glows, display remains blank, start light flashing. Help please


... Whirlpool Dishwashers

Prssure washer m1000 3 hp used to wash boat water leaks from inside cannot find allen wrench to fit wrench has small hole in center


They are probably not allen head screws but rather tamper proof Torx screws. You can break out the small pin or you can now buy special Torx bits with holes to remove tamper proof screws. They should be available at most h ... McCulloch FHH18A Electric Pressure Washer

A round band came loose during a wash. It is a think black rubber-type band. The band is in tact it just need to be put back on, however i dont know where it came from. Dishwasher is a small version if that makes a difference.


That sounds like it came off of your small apliances (blender, food prosecer...) there is not any rubber washers on the inside of 99.9% of dishwashers becauss thay can melt in the heat. ... Dishwashers

My washer is leaking water on the left from the top of a black 3/8 rubber hose. There is no clamp at the top--should there be one?


Sounds like you're talking about the fill hose. If so, it connects to an open fitting on the left side of the tub. It should have very little pressure on it and only when the machine is filling. A clamp there is not usually necessary. You can put a c ... Whirlpool Dishwashers

My frigidare diswasher is leaking from a left side black hose


Check the hose first - it could be split or damaged esprcially if it's old. Check all the clamps to be sure they are tight. Chack all connections to the dishwasher and drain spur under the sink. Check the drain trap fro any leaks. ... Frigidaire Dishwashers

Had the Northstar 3000 psi Pressure Washer for 2 months and it started leaking oil from the pump during use. Took it to Northern and they are replacing the pump under warranty but said it was likely because I was using quick connects on my garden hose coupling and that was restricting the water flow making the pump overheat. They said never to use quick connects on the garden hose unless the opening is at least 5/8". Does anyone make such a quick connect? I hate having to screw the garden hose o


It is easy to check if your hose and quick connects are supplying enough water to the pump. Your pressure washer gallon per minuite requirements are printed on the machine and also on the pressure tips in GPM. Your post indicates 2.5 gpm but check yo ... Northstar Pressure Washer 3000 PSI

Leaking dishwasher The dishwasher leaks a stream of water at the base -bottom left corner whenever it goes into the final rinse cycle. It does not leak when it is in the wash mode. This leak just seemed to develop suddenly. There was no build up -ie a small stream of water. I just noticed a big puddle on the floor one day after dishwasher had completed its cycle water leak in the left side ,bottom ,husband states a small drip,drip and we do not know what to do or replace. No water standing


I just had this same problem and it was caused by a small plastic seal on the bottom of the door. My friend owns an appliance store and he said this is a common problem for this model of dishwasher. The part was $68 and the labor was $60. I could ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

GLD4050 DW won't pump out at any time during wash cycle. Removed lower arm, screen, etc. and washed and cleaned out everything. Removed drain hose and cleaned it out. Reinstalled and ran again. At no time during he cycle does the water pump out. HOWEVER, if I put my hand on the drain pump I can feel and hear the pump running as usual at the right times in the cycle. What else could be preventing the pump out? Thanks!


You could have a plugged pump itself or broken propellers as long as drain and screen are clean which looks like you already took care of that. ... Frigidaire GLD4050RHS Builtin Dishwasher

Water leaks from underneath the unit. Water only leaks when the pump cuts on (pressurizes). It leaks down on to the hose connecting to the water inlet valve on the right hand side of the unit when looking at the door of the unit. When the unit is full of water and the motor / pump is not running the unit does not leak. This unit is a Maytag jetclean dishwasher Model DWU9200BAB about 12 years old


Please change the 'o'rings of drain line and the inlet and also check the drain hose and the inlet if there are any holes in it ... Dishwashers

Hi ..I have an Excell gas pressure washer model no. Exwgv2121-3 with Faip 2100 psi 2 gpm vertical shaft pump..the problem is that there is water leaking from every weep hole at the bottom of the pump when running. Oddly enough,the pump still puts out significant pressure but less than it should due to the leaking water. What is the most likely cause of this?..is it the high pressure water seal(s)? If so,how do I repair it?


... Pressure Washers

I have mod. # FDB1050REB0 the top rack wash/rise arm is not turning at anytime during the wash cycle--- We are not covering the hole into which the water is being pumped---- the bottom washing is turning---- this leads me to to believe the line to the top arm is obstructed from the pump to the wash outlet (in the top of the machine)---- what can I do to check the line?


Hi\015\012\015\012Please check if something is blocked near the top spray arm\015\012and also make sure that all holes are open. Use a sharp metal pin to clean the\015\012holes on the top spray arm. Make sure the water pressure is not low ... Frigidaire Dishwashers

Leaking dishwasher i have an 8yr old hoover dishwasher & it leaks on the rinse cycle. It's coming from underneath on the left hand side as you look at it. I've checked the hoses & clips on hoses, which seem ok. It only leaks as the water is coming into the machine on the rinse cyle. Never any other time, not even when it's filling for the wash cycle!


If your dishwasher leaks, check these:Main tub sealDoor gasket or sealWater-inlet valveHosesMain tub sealNote… If the main motor of your dishwasher is mounted vertically, beneath the center bottom of the dis ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

My dishwasher siemens se25a266gb purchased in 2003 will fill with water go through a wash cycle but does not pump out the water i have cleaned out the filters, checked the exit hose and all seems ok the only way to get the water out is bale out by hand. after this it will run through a wash cycle then stop and not pump out. how would i get to the pump and check it? any help appreicated regards Alan


\012Hi,\012Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - ... Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

Asea Cylinda 1400 dishwasher leaking underneath. Found wash pump seal leaking. Have removed pump and motor but can't remove impeller to get to seal.


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1532 seconds