Having problems with your Dishwashers ?

Replace the plastic panel/facia - Dishwashers


Answers :

Hi,

Kindly tell me the Make and Model of the Washer. Do you want to know the Procedure How to Remove the Dishwasher fascia?

Let me know, so that we could Proceed.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Plastic Pieces We purchased our ASKO 1385 dishwasher 7-8 years ago. Over the years, I have found "small square, thin, pieces of gray plastic" inside. Where are these coming from? Also, we have replaced the drain pump 2 years ago and looks like we'll be replaced the main pump within the next few days as no water is going through. We are looking at paying big $$$ for that pump. Almost half as much as purchasing a new dishwasher. Is this a common problem?


Yes, I have the same problem and it is the upper bearing rack, not the pump impeller. The new bearing kit is $30.00 (another is available for $123.00-the same!!). ... Asko 1385 Dishwasher

I have a Bosch dishwasher, model SHU9915UC/U11. The spring mechanism on the detergent door cracked, and I bought the part to replace it. I took the front cover off of the dishwasher to determine how to replace it. Two white plastic "things", maybe spacers, fell out. I need 2 things: a) how to gain access to the spring on the detergent door so that I can replace it, and b) how to put the door spacers back on. An exploded parts view would probably help a great deal. Michael J. Orr


Hello! This is Guru...Saailer...I have your information...Due to size limitations I'll need your e-mail address in order to send it to you...Send an e-mail to me and I'll send an exploded view diagram and parts list...Guru...saailer... ... Bosch SHU9915UC Dishwasher

I have a hotpoint HDA2000G00WW built in dishwasher. The dishwasher does not run unless you press the plastic door under the latch area. I have adjusted the latch and that does not resolve the problem. I notice that the top three screws that hold the plastic eschucion are no longer holding as the plastic screw areas have broken on the eschucion. Do I need to replace the eschucion or can it be tightened some other way?


... Hotpoint 24 in. HDA2000Z Built-in Dishwasher

Leaking This is a problem that I have when the dishwasher is in drying mode. I will find a 5X5 and sometimes smaller, size water spot under the dishwasher after the dishwasher has stopped. I was told it was the vent were the steam comes out and I had that replaced. It still leaks, then they told me to replace the rubber around the door, still leaks now they order a whole new plastic interior door. Please if you have any ideas what could be causing the problem, please let me know. Thank you


\015\012open the bottom panel 2-4 screw\015\012take a flashlight and turn the machine on\015\012see where it come from\015\012if you need take the unit out a bit f ... Jenn-Air JDB4000AWS Stainless Steel Dishwasher

I have a frig/electrolux gallery series dishwasher: model GLD2445RFC0 serial # TH72896159. On the ceiling of the dishwasher is a gray plastic arm that snap onto a round gray disc that screws into the ceiling. It will not stay connected to the disc eventhough I snap it on with a round white plastic doughnut kind of cap. I have replaced the gray arm in the past because the orig. one fell and melted on the heat ring. This one has : 1546496 1546079 CAV 2 >PP+20TF written


If you go to searspartsdirect.com and type in 154607802 for the part #, I'm pretty sure that's what you are looking for. I broke the exact same part and it's what my husband ordered as a replacement. ... Electrolux Dishwashers

My dishwasher's top rotating sprayer keeps coming loose. The screw and plastic bearing fall out and I think that it has stripped out the end where it seats into the top of the washer. Any ideas on how to anchor this in? Adhesive? A larger screw? The plastic bearing is Part No. 568 and the screw is Part No. 569. If I replace the conduit arm (Part No. 585), will that give it a new, clean spot to screw in too? How difficult is it to replace this arm?


\012Hi,\012That is not that hard to fix and you can easily buy the parts yourself online...Here is a tip that will help you with the online buying...How to Buy ... Dishwashers

G661 SC My Dishwasher wouldn't take the water, and I had a Technician come by. He opened the right side of the dishwasher and said that I need to replace the  large White Plastic Part that transfers the water from the hose to the inside of the dishwasher. Does anybody know the name of it, or where I can find one for this model?


It's called the water intake. They usually dont give too much trouble. Can you give more info on the symptoms please?\015\012Any lights flashing on the machine? If so which ones?\015\012Is any water at all coming in? or is the machine tot ... Miele 24 in. G656SCi Plus SS Built-in Dishwasher

Replacing dishwasher. Inlet hose & outlet hose have plastic fits


The brass fitting should be hex shaped so you can get a wrench on it and it should rotate in the plastic line so it won't twist the plastic hose. Don't forget to shut the water off to the diswasher before disconnecting the supply line. ... GE Dishwashers

Broken fitting The plastic curved piece that attaches the hose to the white fitting on the back of the dishwasher broke, and I need a replacement.  I have been to Home Depot and they don't have anything to fit it, and I was told to go back to the manufacturer for a replacement piece but have looked online and can't find anything that would allow me to order the part.  Help!??


You don't have to change that piece,just tie the hose (drain hose ) to something that is equal height,this prevents siphoning. Please Rate This ! ... Danby 22 in. DDW396 Free-standing Dishwasher

The wheels on which the top rack rolls in and out of the dishwasher have broken so that the rack is no longer operable. The machine works fine and I hate to have to replace the whole dishwasher because some plastic inside has broken, but I am unable to find any place that stocks these parts.


... Equator SB72 Built-in Dishwasher

I have a Kenmore Elite Dishwasher Model 665.13773K600. It seems to have no power to the touch pad (top) control panel. I have already checked the circuit breaker and the power to the dishwasher. A friend said that it may perhaps be the thermo fuse cut out that needs to be replaced. 1) Is this true? 2) How can I remove the 1" thick control panel touch pad after removing the six screws- it seems to be stuck, and I don't want to break the plastic touchpad.


... Kenmore Dishwashers

Maytag Dishwasher Model #MDB7600AWB One of four plastic WHEELs mounted by screws to a 10 inch metal bar located on either side of the top rack has broken where the wheel meets the screw shaft. (These wheels run along the guide tracks for the upper rack mounted on the inside of dishwasher.) Please provide me with a part number so I can order a replacement part. Thank you.


Call Maytag with information of the tag on machine ... Maytag Dishwashers

I have two problems with my GUI1500 dishwasher. The 1st is that when water starts entering the dishwasher I hear a loud hammering/vibrating sound. It's strange, but the sound will stop if I turn on a faucet in the house. The other problem I have is that the soap dispensor will no longer stay closed. The Plastic tab that holds it shut has basically disintegrated. Will this cause the dishes to not come clean? Can this part be replaced? I don't see any visable screws holding it onto the door.


Hi - welcome to FixYa,\015\012\015\012The first problem isn't a fault with the washer, it's a plumbing problem called "water hammer", which is a resonating vibration through your pipes. It's usually caused by a toilet flush valve, but can ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

I have a whirlpool dishwasher model adp 5550 condenser. The dishes do not get clean. I have had a repair man out twice and he replaced the soap dispenser on Friday but it still doesn't work. I went to the store today and bought every cleaning things I could find for dishwashers and also started to investigate online myself. I took the arms off and cleaned them, I took the filter out and cleaned it, and then I noticed that the plastic bar that runs from the top, along the back and into the bottom


... Dishwashers

Maytag DWU9200BAB jetclean dishwasher with broken door springs. found a small piece of white plastic after hearing a loud bang. How can I get to the springs to replace them? I believe the plastic is from the sping linkage.


... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

Hey Everyone! Ok try this one! I have been working on a KUDS25 Kitchenaid Dishwasher. It was leaking like a siv from the bottom. I replaced both top and bottom plastic bearings and also tightend all the screws at the bottom. Leak Gone, I thought. It now has small leaks down both sides. I have since been told by the owner that he took the door apart himself. I pulled out the dishwasher from the cabinet and ran it. I could see the leaks at the top on both sides of the door latch. I cou


Hello davidgalb. You can install a new gasket to seal the door again. That old seal is not flexible any more. That said, for my time and money I recommend a replacement dishwasher, this one has definitely seen better days. Joe ... Dishwashers

Why is my drain solenoid melting on my dishwasher? I just replaced a drain solenoid for our GE Nautilus dishwasher (gsd2200go2ww) because the plastic insides melted and froze up the actuator arm. After a week of happy washing it happened again. What is causing this meltdown?


... GE Nautilus 24" Built-in Dishwasher

This a message for phil. The aquastop valve was not under the dishwasher. On my model, it was fitted directly onto the water inlet pipe. I replaced the valve as you suggested. After removing the old valve you could see through the clear plastic housing that water was leaking inside the valve. Anyway replaced valve but had to split wires and reconnect with connections supplied with the valve and according to instructions. Water leak has now stopped but when 'on' button is depresse


Please provide dishwasher make and model. Looks like you are retrofitting the valve to your dishwasher which may not be getting the correct supply voltage from the dishwasher control. Will need to understand part no. of the replacement valve you ha ... Dishwashers

My dishwasher (Kenmore Elite 665) doesn't use up all the detergent in the detergent cup - it always leaves a little behind at the end of the cycle. the dishes don't get quite as clean any more, either. I recently replaced my old water heater - we were getting lots of little plastic pieces in our faucet screens. I'm guessing that the water pressure may be low, and that it may be due to the same problem. Is there a screen-type filter that filters the incoming water, before it enters th


I don't believe you have a screen at any water feed and doubt that would be the problem. Once the washer fills the pressure to the cleaning arms is provided by the pump itself. I have this issue every couple of months due to hard water and the calci ... Dishwashers

The flimsy plastic guide wheels on the rack for my (ca. 2000) GE monogram dishwasher have been breaking. Six so far. GE wants $25 - $30 per wheel to replace and $235 for a whole new rack!! I will not reward this rapacious corporate behavior. Is there an appliance graveyard (like an auto wreck yard) where one can get a used rack? Are there wheel manufacturers/suppliers that will sell reasonably wheels of similar dimensions to the breaking wheels? Preferably in nylon or stainless steel, not the cr


We have just solved the problem with our wheels falling off! For .75 cents a wheel we purchased new wheel "clips". The connect straight into the wheel instead of "rotating" on. Big differnence and so easy to change out! 5 minutes and the problem is g ... Dishwashers

Maytag dishwasher MDBTT50AWS Door Latch broken. Screws hold the top. The bottom appears to fit into ''plastic teeth'' . Are the teeth supposed to have top and bottom or just bottom teeth. It appears mine has broken teeth on bottom. Is so, do I need to replace control panel to hold latch at bottom.


... Dishwashers

Component failure Actually a Kuppersbusch IGV 645.2 Dishwasher There is a plastic conduit which takes water from the base of the machine to the upper spray arm. This now comes adrift from its connection at the base (behind the lower spray arm) on every cycle, resulting in poor or incomplete washing. It can be replaced easily and seems firmly inserted when done but is always adrift again by the end of the next cycle. Anyone any ideas?


Put a bead of silicone on the tube connection and let it set up good before running. If the tube is in good shape and only comes loose this should be an easy fix. ... Whirlpool GU2400XTP Built-in Dishwasher

My KitchenAid dishwashers door will not stay shut. I have replaced both hinges, the plastic rollers for the tension lines that atached to the spring. Still no luck. Could it be that the locking (?) switch has worn out?


Sure thing. \015\012Our dishwasher is one that we put our own "Door on it" in our case, it matches the cabinet. It is designed for that. \015\012I went on-line and ordered the replacement parts. I can't recall the site but I will look thr ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

The little plastic arm that holds the soap dispenser closed on my model DU1055XTSD2 dishwasher broke off. I can't find the part to replace it.


Must get new soup dispenser ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

The adapter on my maytag portable dishwasher comes off the faucet when I try to run it sending water everywhere! We JUST replaced the adapter and hoses, $50 and not the problem. It seems that the plastic pieces (not metal balls) are wearing out as soon as they're used. Does anybody know what I can do or if that isn't the problem, could it be that I have the wrong end on my faucet????? HELP!!


If you just replaced the connector and it won't stay on, replace the adaptor on the faucet. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1611 seconds