Having problems with your Dishwashers ?

I have AEG Favorit 80800u dishwasher type 45_1 VCD 24 which keeps dropping power off after 10 minutes of operation. No Leds nor error codes. Power enters the unit properly.


Answers :

Have you monitored the the power while the machine is running? Does the power supply receive constant voltage? Or does the power supply shut off?
Can you tell where the power begins and ends? That kind of testing will be necessary to find out.
Hi,

I am sorry to Hear Regarding the Problem. I would like to share Few Details with you.This could be either of the Below Mentioned Problems :-

1. The control is sensing that a touchpad key is stuck and that is why the light is flashing. The only fix is to replace the console. You can test this diagnosis by disconnecting the touchpad ribbon from the control right after you start the unit up and see if it finishes the cycle. You can place the latch mechanism in place with the console removed.

2. You have a bad control board in this, or you motor is overheating and shutting down.

You could Disconnect the Power Supply for Few Minutes, say 30 minutes and then Turn it ON to see, if that could Reset the Dishwasher and solve the issue.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!


Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have AEG Favorit 80800u dishwasher type 45_1 VCD 24 which keeps dropping power off after 10 minutes of operation. No Leds nor error codes. Power enters the unit properly.


Have you monitored the the power while the machine is running? Does the power supply receive constant voltage? Or does the power supply shut off?Can you tell where the power begins and ends? That kind of testing will be necessary to find out. ... Dishwashers

When I start the top drawer it defaults to 5 minutes (with the lights Heavy, Fast, Rinse highlighted) runs for a couple minutes, then stops and the LED starts randomly cycling through all kinds of codes very quickly. There is water in the tub that has not drained after completing the couple minutes of operation. This cycle repeats itself if I hit the power button again after the LED starts freaking out. The 5 min cycle shows in the LED, sometimes with the no circulation error, sometimes with the


Here is the solution: \015\012http://applianceguru.com/forum1/24814.html ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Bosch she4am Unit starts briefly, then stops about a minute into the operation and lights the CLEAN led. I located the diagnostics code paper, ran the test a few times, and come up with the same code...the CLEAN led lit indicates a door switch problem. I removed the door switch, it's a magnetic hall effect transistor..seems to work but not sure it's showing proper voltages. It reads 8vdc or so across the switch with door open, and about 11.7vdc with door closed. Seems too narrow a range to me


... Dishwashers

Homelite 1500 psi dual--- when using the wand, the unit (electric) powers on and off with no pressure This is after operating properly for 25 minutes. Help!


... Pressure Washers

We have just moved into this unit fitted with a MIDEA WQP12 - 9011B dishwasher with NO MANUAL. What can we do ? We have been using the dishwasher by turning the operating KNOB to a position and pushing in the POWER KNOB. The machine then goes through a cycle of 80 to 100 minutes but without an USER OPERATING MANUAL, we have no idea of whether the dishwasher is being operated correctly.


... Dishwashers

The "clean light" on our Kitchenaid KUDIO1FLSS flashes 7 times and I cannot clear the problem to allow the unit to operate. Is there a sequence, using the control buttons, to permit the unit to run a system check? I disconnected the power for 30 minutes but that did not solve the problem.


... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

I have a new Bosch Dishwasher.I just turned the Unit on and 10 Minutes into the Wash Cycle it comes up with Error Code E 16. There is no information in the Operating instructions about what this means or how to fix it. I have been on the phone for 1 hours on hold listening to elevator music after ringing BSH Home Appliances Pty Ltd Customer Care I just install in using the Installation Guide. I have 20 years experiance in Appliance Repairs. Does anyone know what E 16 means and what is the fix.


... Bosch Dishwashers

Our Bosch SHU43C06UC/17 dishwasher stopped working properly today. The power scrub cycle starts at 115 and counts down to 112 and then stalls -- no sounds of water entering the unit... no further counting down The regular cycle starts and shows 97 and counts down to 94 and stalls. no sounds of water... no further counting down. We hear a constant buzzing sound. Can you help?


... Bosch Dishwashers

The top drawer is running through all the setting numbers in rapid fashion. even when it is powered off it restarts the series over after a few minutes. the lower drawer operates properly


I suggest take a clean damp cloth and wipe the edges of the drawer door top and sides, especially the sensor switches that control the programs. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I am having issues with my dishwasher where it appears to be working but does not clean. Hot water does enter the unit and drains properly but is not cleaning. Muck is still on the door, the arms are wet. Also, normal cycle with no extra features selected (i.e. High Heat, etc.) takes over 1 hour and 20 minutes. Sounds appear to be normal, draining, filling, etc. Thanks!


No\015\012 you need not wash the dishes but just cleaning of the debris and then \015\012putting it in the dishwasher for proper cleaning will help you to \015\012prevent the drain from getting blocked.\015\012\015\012 ... Dishwashers

Our GE built in dishwasher Model GHD6310L18WW had no lights on and would not operate. i checked the breaker panel and found it was OK and 120vac were flowing to the unit. i then turned the braker off for 30 seconds then back on .this made the time remainig LED display sow 106 and the Normal wash Cycle LED is lit as well as the extra Heat LED . the unit will bot operate though


... GE Dishwashers

Brand new haier hdc1804tw wont start. i press the power button unit beeps once and power light comes on but i cannot select cycles. unit will then beep every five minutes. i have made sure there's water and unit is level. i have left it unplugged for over five minutes with same resulting issue.


... Haier HDC1804TW Dishwasher

I have a Baumatic BDW 45.1 slimline dishwasher, the unit will power on but I cannot select a program. I was able to place the unit in to reset mode once by holding down 'P' and power cycling the unit. This then allowed me to choose a program and complete a full wash cycle. Now I cannot repeat this steps and the unit remains with just power light on. There are no Error codes displayed at all. Could this be a problem with the front panel?


... Baumatic 18 in. BDW45.1 Built-in Dishwasher

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

We bought a Bosch SMS63M08AU dishwasher and are currently installing the product. We have connected everything, however the unit comes up with an error "E17" after a few minutes of running the unit. Can you advise what an E17 is and how the error can be rectified. Regards Kevin Brown


... Bosch Dishwashers

No power unit went dead checked power to base of unit ok also shut off breaker for 10 minutes to see if it will reset, no luck. Also removed inner door panel to reveal circut board to look for a reset or small fuse, none evident.


... General Electric GLD5960NSS Stainless Steel Built-in Dishwasher

Lights on Dishwasher light up but nothing happens. When I reset power it lights up the high temp and sanitize button light up and LED displays PF. After I open the door they stop flashing. the far left five buttons light up when I push them and a corresponding number displays on the LED screen. the only lights that do not come on are the Delay button and power button. Don't know if they are working or just don't light up. No matter what lights up the unit does not turn on....:( ? help can't fin


Pf is power failure\015\012 your loosing voltage to the unit \015\012it may just be the door switch or it could be in the control\015\012 try starting the unit but keep your hand on the unit pushing the door in place,, its not a g ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

GE Triton XL control panel suddenly went dark. Would appear the power is off but breaker tested ok and power verfied. I unpluged the unit for about 5 minutes. When I reconnected to power, 2 short beeps were heard but no lights on the panel are on. Any other ideas?


Hi\015\012\015\012 \015\012\015\012Thanks for using FixYa. From what you have\015\012described it seems that the control board has gone bad and should be replaced\015\012however, before replacing y ... GE Tritonr XL GSD6260JCC Dishwasher

Suddenly, an error message appeared on the display of my Frigidaire gallery series dishwasher, model number GLD3450RDS0. On advice from Electrolux customer service, we cut off the power supply for one minute. When we turned the power back on, the display read PF (for power failure), but then it went completely black. Any advice?


... Frigidaire Dishwashers

Model JPX-300H, the unit does not fill, but it will drain if you fill with water from a bucket. Also when the unit drains there is water coming from under the unit. How do I check the fill valve for proper operation. Thanks


The fill valve is easy just take the coil off and there is a hole in it put a metel screwdriver in the hole and turn the unit on if it pulls the screwdriver like a mganet it works is more likely i bad diaphram now as for the draining it drains bu ... Jackson 24 in. JPX-300H Built-in Dishwasher

Hi threr I have the following problem with my Haier DW12-EFM dishwasher: The dishwasher seems to operate properly for the first several minutes untill program selector knob stops betwin position 2 and 3. After I turn it manually it keeps on turning and than it stops again after I turn it again it operates till the end of the program but the dishes are not clean enough to be used. I also noticed that the heater does not operate (water is cold). Do you know wht the problem might be. Reg


... Haier 24 in. ESD100 Built-in Dishwasher

I have a Siemens dishwasher SE64530/17 type S9 V15 Unit powers up and appears to begin wash cycle. However little or no water enters unit. Unit is about 12 years old and has been working fine. There have been no changes to installation, plumbing or electrical.


... Siemens Dishwashers

I have a Gallery 900 series GLDB958AS dishwasher. The cycle status lights (just right of the "time remaining" status window) continually blink. None of the buttons on the front panel work and every 10 minutes or so the water pump starts up for about a minute then shuts off. No water enters the dishwasher. I tried turning the power off then on but there is no change. Every so often a random cycle light will blink or light up for a minute, then turns off.


It seems that there is error on the program controller unit. All you need to check if that if there is moisture build up on the panels thus causing the programs to go harewire.\015\012So remove the panel and disconnect the wires, check all lead ... Frigidaire 24 in. GLDB958A Energy Star® Built-in Dishwasher

Kitchenaid model KUDIO1ILBL6 The lights for Heavy Cycle ,Normal Cycle and Cancel blinking at the sametime constantly. The tech sheet is missing and the unit is appox. 5years old.have shut power down for 5 minutes .When power turn back on only the Heavy Cycle light blinks costantly. Have Ohmed out the door switches and check adjustment OK. Checked board strips and plugs for good clean and tight connections OK. Thanks


Hi, You need to reset the unit by pushing the buttons. Push the heated wash/heated dry a few times. All the lights will light up and the dishwasher will continue its . Let ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

The Fisher Peykel dual drawer dishwasher : the top unit LED is off and the setting for length of wash is not lit up and is not functioning. There is power to unit because when I hit the lock button it beeps. Also the red light for the glass cleaning liquid compartment is lit. What seems to be the solution? I am an ME and hands on type, please advise.


Can you see a small lock inside the display panel??? the control may be locked. another issue might be a broken heater plate, not a very home owner freindly part to change( heater plate has a fuse inline that would kill power to function ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1352 seconds