Having problems with your Dishwashers ?

When starting my Bauknecht GSFP 5586 dishwasher the program is set for rinsing and the start light flashes two blinks, then again two blink etc. I cannot get the program to change. When I hold the Start button for 2 seconds, the progress light flashes at END for a moment then reverts back to the double blink sequence. I have checked the filter and it is well seated and clean. What can I do to start the program selection again?


Answers :

Ok, so I had the exact same problem with the exact same model. NOT 7 blinks and to buttons that you do not have.
\012I will tell you what I did as I do not know what (if any) of what I did fixed it (it could be luck but I do not think so).
\012
\0121. I pulled the washer out of place. You should see a small thing connected on the inlet pipe that is supposed to stop flooding. I gave that a few taps. (I am quite sure that this is not the fix but who knows).
\0122. I pressed the start (rest) button until the washer started to reset (whet to the END mode). I DID NOT wate for it to end. While it was pumping I turen the washer off using the power button. Then I turned it on again. I went on pumping. Then when it stopped pumping I turned it off again, waited toe 2 seconds and turned it on. Much to to mu surprise when I turned it on it was working normal.
\012
\012I hope it goes on doing this as this in only the second problem we have ad with it in 13 years.
\012
\012Hope this hels
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When starting my Bauknecht GSFP 5586 dishwasher the program is set for rinsing and the start light flashes two blinks, then again two blink etc. I cannot get the program to change. When I hold the Start button for 2 seconds, the progress light flashes at END for a moment then reverts back to the double blink sequence. I have checked the filter and it is well seated and clean. What can I do to start the program selection again?


Ok, so I had the exact same problem with the exact same model. NOT 7 blinks and to buttons that you do not have.\012I will tell you what I did as I do not know what (if any) of what I did fixed it (it could be luck but I do not think so).\012 ... Dishwashers

My bauknecht dishwasher gsi 4743 is not working. When I turn it to the program the start light is already blinking and when I press start the end light flashes and the pump appears to run for a few seconds and then the whole thing stops but the startt light continues to flash. If you could help, I would really appreciate it. Thanks!


... Bauknecht Dishwashers

Clean light comes on my Kenmore Elite Dishwasher Model # 665.17263. This happened once before and has to do with the heating element. The service guy showed me how to press the buttons in a certain sequence to "unstick" the unit and it worked fine. The Quick Rinse light keeps flashing. When I push a previous sequence recommendation it switched to pots n pans and Quick Rinse and Cancel all started blinking. Then in about 2 minutes went back to Quick rinse. I did one sequence and it started to d


It seems that there is something stucks in your dishwasher...is there any error code? ... Kenmore 24 in. 15079 Built-in Dishwasher

Tecnik DW2677 Hi, my dishwasher regularly starts to bleep after starting a wash program. When the door is opened it stops bleeping and the right hand light flashes 7 times repeatedly in sequence. By holding down the start and program change buttons together for a few seconds, it will reset. If you then close the door all is well for a few seconds the pump sound like it expells some water and then it starts to bleep again. The above process can happen several times before it decides to do what it


Check your water intake- i had the same issue - a leaky fitting wasn't supplying enough water to the dishwasher. had exactly the same symptoms you describe. fixed the leak, reset the dishwasher & it's working fine.\015\012\015\012\015\012\0 ... Tecnik TDW2677 Built-in Dishwasher

The stop/cancel light keeps flashing. I have tried Heated dry to Normal sequence buttons and I have tried Heated dry to High temp wash sequence. When I have pushed soak and scour the stop/cancel light stops and the Pot/pan and Normal wash lights start blinking


Unfortunately I cannot view the comments from other fixya.com consultants so I am coming in cold on this one.\015\012\015\012But it appears you are trying to isolate the problem of why the stop/ cancel light are flashing. I suppose the on ... Whirlpool 24 in. DU1100XTPS Built-in Dishwasher

Miele Inspira G2180 SC SF dishwasher problem We start the Normal cycle and after the dishwasher fills up with water the units starts beeping, all six program lights start to flash, and the water drains out. The lights remain blinking. What might be the problem please? Dan


... Dishwashers

Just bought and had installed on 9/25/10, Kenmore Elite dishwasher model #665.13929K010. Start light on the front panel flashes, then runs through all lights and ends on the complete light which contnues to blink. It will not actually start the wash process at all. Before I call Sears to come out, what is the reset sequence for this model? Any other solutions you can think of?


... Dishwashers

GE MODEL 5900N10BB. TWO LIGHTS ON FRONT ARE BLINKING-THE HOT START AND NORMAL WASH- DOOR IS OPEN, BLINKING LIGHTS AND PERIODIC SINGLE BEEP. WHEN I CLOSE DOOR, FLASHING CONTINUES, THERE IS A SOUND BUT NO WATER - NOTHING HAPPENING


Hi. I am actually having the exact same problem. Anyones help would be greatly appreciated.\015\012Thank You ... GE GLD5900NWW / GLD5900NBB / GLD5900NCC Dishwasher

My smeg dishwasher seems to be permanently in wash mode. The light on the menu of settings no longer flashes, but permanently is on, and when I run a load it never stops. I hear the two beeps as if the dishwasher is starting a load so it seems to be cycling through over and over. How can I fix this and get the blinking light back? Thanks


You have a timer relay issue ,probable need a new board for it ,a cheap fix would be to time it and see how long it take to run full cycle and put a regulaer outlet timer on it or a alarm off your stove or what ever,save a couple of bucks ... Smeg STX2 Dishwashers

I have a GE dishwasher model number GLD55OOLOOWW. It was starting a start cycle and i opened the door to put more dishes in and my finger must have hit a button on the door and now two lights flash off and on and it wont reset itself. It has been on for several hours and still blinking and beeping every so often and unplugging it does not help. Any suggestions how to solve this problem. Thank you.


Try pressing the cancel button ... Dishwashers

My dishwasher, a Whirlpool ADP 931, has stopped working. Possibly because the door was opened during operation, right after it was started. There is some kind of error condition indicated through a blinking Start light, but I don't know how to analyze this. This is a quite simple model with very few buttons to press. When I turn the program knob right to start it, the only thing that happens is that the green Start lights begins to blink continuously. There is also another green light


Hello & Welcome to FixYaThis light is reset by pressing two buttons in sequence 3-4 times, to reset your dishwasher press these buttons in sequence:High tem ... Dishwashers

Kitchenaid does not do the program, I can start the program, but about 15 minutes into the program the program stops and the light jumps to clean light which it 7 times blinks pauses and 7 times b


Clean all the buttons , one must be stuck , push all the buttons and un stuck them.... ... KitchenAid Dishwashers

Just fitted a new circuit control board for my indesit di62, the test cicle started and ran until finished. I heard two beebs to tell me cicle had finished but when I looked at the program selector the second and third lights were flashing. Had a chat on the forum and it mentions about draining off a flood tray but not sure how this is done so looking to confirm that this is the error message and how to correct it. thanks Dave.


Leave outlet hose flat down ground level ... Dishwashers

Hi...my dishwasher 'clean' light continues to blink. I can hit cancel and it sounds like the cancel cycle is running. After that the light keeps blinking and I can not start the machine. If you hit start the light goes on, then stops, and the clean light flashes again. Any clues? Thanks!


Sounds like the control board or panel is shot. What is the model number of the unit, and serial number? ... Dishwashers

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

I have a fridgidaire dishwasher model # FDB 1450chc2 andon the control panel the red lights are flashing and washer wont start ?? when I open the door the lights go out but when I close the door and push start the washing lights start to blink but doesnt start to work ?? Need help thanks [email protected] Brian


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

When I turn on the dishwasher, the light on program 6 flashes but the program will not start.


... Smeg 24 in. DWI612 Built-in Dishwasher

Candy dishwasher 2 program lights keep flashing after program starts then stopas and flashing starts


My candy dishwasher Model No CDI 3015-S retains water in the bottom of the machine at the end of the program. I have checked the filter which is clear so do not know what else to do to clear the problem. Anyone faced this problem or know what might b ... Candy 17 in. CS455 Built-in Dishwasher

Hi I have an F&P DW691 dishwasher (manufactured by whirlpool) the reser light is permanently giving two quick sucessive flashes and will not start the machine unless held on for 6 seconds, the machine then starts for a minute then stops and goes back to the two flash reset problem. Does any one know the fault code applications for this model.thanks Mike


Hi, I've got the same dishwasher but with a different fault, there's power down the cable to the d/w but no power lights on the front panel?Thanks. ... Fisher and Paykel Dishwashers

After selecting a program, the dishwasher beeps for a while and the 3 buttons on the left flash too. Program wont start, water wont fill and nothing happens. THe lights keep flashing but the beeps stop for about 30 secon ds then start again. Help me Please.


Basically the dishwasher is telling you there is a fault - Not so useful I know! Plug out the machine and leave it for five minutes and see will it reset. If that does not work, you will need to reset it manually. To do this consult the manual. If yo ... Hotpoint 18 in. DC28 Slim-Line Built-in Dishwasher

Kenmore dishwasher 665.16029402./ clean light flashes 7 times. i did the push button sequence to reset. started to wash for awhille and during the wash it stops and green light starts flashing again


... Kenmore 24 in. 16032 Built-in Dishwasher

I have a dish washing machine bauknecht model gsx 7988, when closing the frontdoor, the pump starts to run and a beeping sound is noticed, this beeping sound and automatic running of the waterpump happens on any selected program, when opening the door, the grren startligt is flashing two times fast,then a halve a second out and then flashing again two times fast etc.etc filter is clean, waterpressure is ok, eno other program can be started.pls help.


... Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

I have a de dietrich built in dishwasher model DVH610JU1. The program appears to start but no water enters the machine and when I open it the lights flash (program light and end program blue light)


... De Dietrich 23 in. DVI130 Built-in Dishwasher

Flashing lights My GE model # GHDA455L00CS Quiet Power a dishwasher's lights are flashing when I start it, will not reset or in-take water. I've tried unplugging it and restarting. Nothing. Tried removing door door screws and press down door latch. Still nothing. HELP!!!!!!! IT WILL NOT PROGRAM. IT HAS A FLASHING LIGHT. WE HAVE BOUGHT EVERYTHING BUT STILL DOES THE SAME THING


It mite be the circut board problem..just  re-soldered a few of the pins in it and things will be back in working order. ... GE Profile PDW8400J Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1579 seconds