Having problems with your Dishwashers ?

Hoover Heds668-80 dishwasher, first fault was a broken door lock which has been replaced. The machine has done one pre-rinse and one full wash cycle. Now whenever we try to run any program it starts, drains, pauses then after 5 minutes beeps 30 times with the pre-rinse and wash lights on.


Answers :

Hi.

The two lights and the beeping will normally indicate long filling rather than drain problem. For this reason the fault is detected at start.

As first thing follow the troubleshooting indicated on the user manual. Check the drain well, and remove eventual water and debris from the bottom of the tub and from the drain well and filter.

After that reset the machine by holding down the start button for about 8 seconds.
If that does not work also try resetting the machine by disconnecting power. Trip the circuit breaker or try disconnecting the power cord for two minutes to reset the appliance.

If still no luck, then there is a fault.

If the problem is long filling, in that case check if there is water getting in the machine.
If there is no water at all, the first part to be tested is the inlet valve.
The valve is tested reading Ohms at its contacts with the multimeter set at Rx1. When the valve solenoid is broken, the reading will return no continuity.

If water is getting into the machine, then part to be tested is the water level sensor. On Hoover branded machines this is usually a float sensor. The sensor must be checked to ensure the floater is not stuck and that the switch is opening and closing the circuit.

If your machine is faulty and the error does not clear by holding down the start button, as first thing call the Hoover at the number listed on the owners manual. They will give you part prices and a quote on repair.

Regards.
Http://appliancejunk.com/forums/index.php?action=downloads;sa=view;id=229\015\012\015\012\015\012
\015\012OK above is a service and repair manual, although, a generic one, they are all essentially the same, and this can be used to troubleshoot and diagnose the problem, and thus repair it.\015\012
\015\012This Fix below, may NOT apply, however, it is amazing just how many times, regardless of the "Cause" that the doing of the "Procedure" actually fixes the unit for good. So is worth a try....\015\012\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing.
Now this happens because, the STOP Button, is pressed and the "Door Opened", during the Wash Cycle. This should NOT be done. You shouldNEVER TURN IT OFF MID-CYCLE. you should instead, Simply, pull on the handle, to Open the door, the system will take care of everything, after, you close it,and pick up where it left off. The turning OFF, makes the machine "Think" that a New Cycle, is going to be done, before the old one is finished, and resets itself to do it all again. But it still has water, that's not meant to be there so it must dump it out.
Now, the FIX. Take the Dishwasher, out, and tip over on it's side, tip to about a 45' angle. Water will come out from underneath, this is from a small "Overflow" reservoir. this reservoir has an "Anti-Flood" switch. The removing of this water will "Reset" this Switch, and allow the dishwasher to work again.
So what happens, is this, when the STOP button is pressed Mid-Cycle, the machine must "Dump" whatever water is still in the machine, into the "Overflow Reservoir". This water then causes the Anti-flood switch to jam, and this stops the machine, until it is reset,by the above method.
\015\012
\015\012http://fixitnow.com/wp/2005/10/12/bosch-dishwasher-diagnostic-procedures-dishwasher-repair/\015\012
\015\012DIY help site. Bosh dishwasher diagnostic procedures.\015\012
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hoover Heds668-80 dishwasher, first fault was a broken door lock which has been replaced. The machine has done one pre-rinse and one full wash cycle. Now whenever we try to run any program it starts, drains, pauses then after 5 minutes beeps 30 times with the pre-rinse and wash lights on.


Hi.The two lights and the beeping will normally indicate long filling rather than drain problem. For this reason the fault is detected at start.As first thing follow the troubleshooting indicated on the user manual. Check the ... Dishwashers

Hi, we have a Hoover HEDS668-80 dishwasher at work. The first problem we had was none of the programs would run this turned out to be a broken door lock. After replacement we managed to get one pre wash and one wash program to run, now when we try it, it starts but after 2 minutes the pre-wash and wash lights flash and the machine beeps 8 times. Can anyone help?


... LG LDF6810 Built-in Dishwasher

Problems with Danby DW1899WP. My husband and I ordered it from Wal-Mart online and picked it up yesterday. We've read through the manual several times, filled all the appropriate receptacles, plugged it in, hooked it up to the water, loaded it, set it, started it, and it doesn't work. It runs the pre-wash rinse for about five minutes before giving a series of beeps, draining the unit, and switching straight to the dry cycle without actually washing the dishes. Help!


... Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

My Integrated Hotpoint BFV620 tried to start a wash but after a few seconds it beeps and lights 1 (Pre-wash) and 3 (rinse) flash - anyone know what the problem is?


... Hotpoint 23 in. BFV62 Built-in Dishwasher

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

See below Hi, Disconnect the Power Supply for Few Minutes, say 10 minutes and then Turn it ON. Do you see any Error Message on the Display? Do you see any Other Light Blinking? Have you tried to Press Cancel / Any other Button on the Touch Pad? Is it Working? Do you hear any Beep? Let me know, if needed further assistance. Hope i helped you. Thanks for using ' Fixya ' and have a nice day!! Comments: Apr 02, 2010 - Thanks for your response!! One more detail, i wanted to ask - Is that Wash Li


What's going on here? ... Dishwashers

We have a Whirlpool ADG 7560 dishwasher which has recently started playing up. When switched on for a normal wash, after a short time the machine starts to beep. If you open the door the green programme light is on the pre rinse and the start light is flashing. After starting the cycle the few times eventually it works normally. Have cleaned all the filters etc.


... Dishwashers

My Bosch SHU5316UC won't finish cycle. When I turn it on it resets to 13 minutes and goes down to 1 but stays at one and never finishes. Except on rinse and hold where it goes to 1 and stays there. It would run all night if I let it. How do I reset adn try to fix it. I tried to hold POWER SCRUB and REGULAR WASH as suggested by manual and no luck. Any help?


Hello, welcome to FixYa. ... Bosch SHU5316UC Dishwasher

Dishwasher does not wash simply beeps continously and wont start the rinse cycle with green flashing pre rinse light. Have tried turning off at power and have checked all connecting pipes. Have emptied dishawasher also all to no avail.


If your dishwasher is a whirlpool or IKEA then maybe the answer given by emmanuelr in "Whirlpool dishwasher ADP5962 F7 error code" may do the trick. It certainly worked for me. Bit technical but if you are happy taking the sidepanels off the thing th ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

My Kenmore dishwasher model #66515639000 quit working. It was washing dishes just fine one day and then the next the buttons weren't working properly. The pots & pans button was flashing with the cancel button. After searching on your site, I tried to resent the control panel by pressing the normal wash button and the air dry button 3 times then opening and closing the dishwasher. Now the quick rinse button is flashing. Any ideas of what to do now?


... Dishwashers

Hi I have a Bosch dish washing machine. The glasses come out cloady and white when washed. It was perfect in the beginning but it is getting worde. The salt is full, the rinsing liquid is full and set right. I used to use the 3 in one capsules, but now I am trying the seperate salt, powder and liquid but nothin gis working. I have also cleaned the washer with that plastic holder filled with liquid a few times, but it doess/t make a difference. Please help. Melani


First thing to try is to use the capsules and see if they work. Try reducing the detergent a little. ... Bosch Dishwashers

My whirlpool ikea dwf 416 dishwasher has salt light on first time in 10 years not needed in my area it will not wash or stop beeping i have checked manual on salt sensors and tried every one of them n


... Whirlpool Dishwashers

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

When the unit switches from Pre-Rinse to Wash, the Drying Light comes on blinking and the unit beeps. The unit continues to run for about a minute, then stops. Previous to cabinet installation, the unit worked fine for about 4 complete cycles.


... Danby DDW1809W Builtin Dishwasher

We cannot keep temperature of our Jackson Tempstar dishwasher at a constant temp. One time the rinse will be down a bit and then the wash. We have replaced the gauges, thermostats, motor and element of the diswasher. It is kept constantly clean, and we have tried everything we can think of. Would there be a wire that could be coming loose every once in awhile that may cause this? Thank you for any help you can give us.


... Jackson 25 in. TempStar HH Free-standing Dishwasher

I have a F&P DD603I with NO lcd, just lights on top at the wash control panel. The HEAVY, FAST, and RINSE lights are all on at the same time. At one point the thing was playing the national anthem (seriously, The Star Spangled Banner was beeping away). Anyone know how to exit this mode and get me back to normal operation?


HI- I think your controller is faulty. I've only encountered the Star Spangled Banner issue once and replacing the controller fixed the issues. You may try to unplug the power cord for a few minutes and plug it back in and see if it resets but I d ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

Hello, Our Fagor LFA-013SS Dishwasher hasn't worked in a few days. It stopped working when it beeped 3 times after doing a load. On the machine it says if it beeps 3 times it means there's no drainage. My husband and I tried to fix it but we're not handy! So we tried calling repair companies but so far no one can repair Fagor dishwashers...help! Thanks


... Fagor LFA013 SS 23 in Builtin Dishwasher

My Bosch SHE45M built-in dishwasher is suddenly taking an extra-long time to go through its cycles. On Regular wash it will countdown from 117 minutes to 31 minutes. When it hits that time it resets to 87 minutes, then counts down to 1 minute and will not stop. I have to hit the cancel-reset buttons for it to drain. I have tried to do a hard reset by cutting the power at the breaker for 20 minutes or more. I'm interested in potential parts and a description of how to fit it! Thanks in advance.


... Bosch SHE45M06UC Built-in Dishwasher

Hi I have a Blanco dishwasher BFDw8 which is having poor wash results in the top tray I have tried all the trouble shooting things in manual. Investigated further by opening door during wash cycle several times and discovered the top arm is not moving although water is still coming out of the arms. I did get a split pea particle out of the arm approx 2mm and have since had a mildly better wash and have used superior wash powder and rinse aid to try and help. Also have put a cleaner through di


\015\012\015\012Check the water temperature. Should be 125 to 140 F. \015\012\015\012Check pump re-circulation., Listen, see if it sounds like it is spraying the water around with enough pressure. ... Dishwashers

During wash cycle it gets stuck and won't move past the wash cycle. On a regular wash it is at 28minutes and when it is on a fast wash it is at 25 minutes. If I stop it and turn on the rinse cycle it will run through the 12minute rinse cycle with no problems. It is only the top dishwasher that does this, the bottom one is running just fine.


I've got the same problem with the bottom drawer on the DD605. No fault codes were set. I checked the heating element and it produced heat quickly. I suspect that the water temp sensor isn't satisfied, and the timer is waiting for the water to rea ... Fisher and Paykel DD605BK Dishwasher

When trying to start the dishwasher, pressing the Normal wash button, the dishwasher gives a huge clunk and then it trips the circuit breaker. Upon resetting the breaker, I tried the next button over, which is Soak and Wash, and it seems to go thru the cycle fine. Another time I tried the Normal button, but put the left dial on Rinse and it started up, but it would clunk periodically and it seemed to have a 'hot' smell. I'm worried to use it - what could this be? Is there anything else I can try


Hi\015\012\015\012This is a very dangerous situation you must remove from the wall supply and desist from using, such a fault could easily make the casing "Live" and anyone touching it may be killed. You need to discover why this is happe ... Dishwashers

I have a kenmore elite dishwasher model # 665.1392 I had set it for a wash with th 4 hour delay and that shut off and now the complete blue button is flashing 4 times with a pause and then flashes 4 times again. If I open or shut it, it beeps 15 times. I tried doing the normal wash - heated dry back and forth trick but no luck with that. Any suggestions?


... Dishwashers

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti


Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1720 seconds