Having problems with your Dishwashers ?

I am getting a default code of "HO" after the dishwasher runs for about 20 mins. The dishwasher is a Fridge Model FDB2310LCC2 What is the "HO" default code mean?


Answers :

HO... is Water Heating, this means that the water is still heating.\015\012
\015\012This can sometimes mean that the element, that heats the water isn't working, or the controller, or a Sensor, you will have to troubleshoot to see. use the manuals, and websites, to do this...\015\012
\015\012http://www.hammerwall.com/Manuals/Frigidaire/Description/FDB2310LCC2/Frigidaire%20Dishwasher%20Service%20Data%20Sheet/154476001/\015\012
\015\012
\015\012http://appliancejunk.com/forums/index.php?topic=2936.0\015\012
\015\012Ok above is your service and repair manual, choose almost any of those manuals shown, just choose one as near to your as you can, as they are all generic, and you can use this manual to troubleshoot and repair your dishwasher. Below are some good DIY help sites too for you.\015\012
\015\012http://www.managemylife.com/mmh/Troubleshooting_Guides/Dishwasher.pdf\015\012
\015\012Dishwasher Repair Guide: How To Fix a Dishwasher - ACME HOW TO.com\015\012
\015\012
\015\012
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am getting a default code of "HO" after the dishwasher runs for about 20 mins. The dishwasher is a Fridge Model FDB2310LCC2 What is the "HO" default code mean?


HO... is Water Heating, this means that the water is still heating.\015\012\015\012This can sometimes mean that the element, that heats the water isn't working, or the controller, or a Sensor, you will ... Dishwashers

What does the code NE mean on my LG dishwasher? it gets through about 10 mins of a cycle then bleeps and the code NE is on the screen. I tried putting it on a different cycle and starting again but the same thing happened. ive only had this dishwasher about 5 week, i checked the manual for the code and it isnt listed among the trouble shooting codes there


... Dishwashers

The power is going to the dishwasher. The on off buttons work. No error codes. The salt light is lite (has been for 5 years) but now I get zero response when shutting the door (after selecting any of the 6 run options). There is no noise, no water, nothing happens. How do I repair this dishwasher so that it will run again?


Door switch failure. This will shut down all other start options. Inspect and possible replacement. See if you can activate it with something with door open. Give it a good close look... ... Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

We have a Kenwood KDW8ST2A dishwasher. We used to get the error code E3 (when still under warranty) and were told not to use dishwasher tablets as it generated too much foam. The problem has been intermittent but now we get the E3 error every time, no matter what program we run, or how little detergent we put in. I've a feeling its not heating up properly, is there any way to check the heating element? Is it worth attempting a repair?


... Kenwood KDW243A Builtin Dishwasher

My bosch dishwasher wont dry. The model number is she44c02uc/47. I don't know what codes i need to see to get it to heat. I've tried to hold the cancel drain buttons in to change the code. I get a C1. what does that mean. Thanks for your help. john


... Bosch Dishwashers

My lg dishwasher is running ok but i randomly get the LE error code. I noticed that when it runs the cycle it takes 3 times as long to run than normal. Is this the motor or the electronic panel. the wiring is ok already checked.


Motor might have something blocked in the coils. mine did the same thing and found a piece of plastic melted in the motor housing ... LG 24 in. LDS 5811ST Stainless Steel Built-in Dishwasher

I have a whirlpool aquasteam 6 series dishwasher and no matter what cycle i run i get error codes f8 and e1


... Whirlpool Dishwashers

Pump problems I had a fairly light load of dishes that needed to run so I thought I'll put some plastic fruit on the top rack to also get clean. Well, when the load was done and I opened the door everything was covered and I mean everything with a whitish substance aka wax! One of the fruit was made of wax an melted all over the entire interior of the dishwasher. We had 30 people now arriving for dinner so I just left it all alone. I should have run it again immediately but I didn't. Now after r


Hi murrie825,\015\012\015\012I'm Harvey the Master Plumber.\015\012\015\012Your problem is: you can't get the pump to drain and can't figure a way to get at it.\015\012\015\012It sure sounds like the pump is clogg ... Dishwashers

Have a Kenmore Freestanding Dishwasher that was working when hooked up to the sink. When we plumbed it in and connected the electrical directly, we now get an "F4" flashing on the panel with a beeping noise and the pump sounds like it wants to drain but just get a sucking noise. I've tried putting water in it to prime the pump, but still doesn't want to work. Do the codes mean anything, or point to a specific part?


... Kenmore 24 in. 16332 / 16334 / 16339 Free-standing Dishwasher

I have a Frigidaire ?AquaSurge with Speed Clean? Dishwasher Model FDB4315LFCO. After the dishwasher has been running and seems to be at the drying stage, I get this coded message: working/drying ER Clean S. What gives? Thank you so much for your help!!


... Frigidaire Dishwashers

Hello, dishwasher whirlpool ACP 4738 display fault code fb (f6 ?) after 3 minutes run. Do you know what fault code means ? Thank's DT


... Whirlpool Dishwashers

My Bosch dishwasher, model SHE58C did not completely drain. We were eventually able to use the cancel cycle/drain procedure to get the machine mostly drained, but now all the lights are lit on the panel, and the count down display is 11. I haven't figured out how to reset. I have tried to hit "Cancel drain" and turn on the machine to get into diagnostic mode, but I can't figure out what the codes & light combinations mean because my model is not in any of the online sources I've found


I have managed to pick up typical diagnostic error codes for a bosch dishwasher - these are\015\012\015\0120 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault\015\0121 = Aqua Se ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

I have a Maytag Quiet Series 400 and I can't get it to run on Normal,lite or other. I get a code 82 that appears. What does this mean?


My maytag quiet series 400 won't select Auto Clean, Heavy wash or rinse cycles. I cleaned the ribbon cable connection where it attaches to the control board. All buttons now work except for the auto clean. There was a residue on the connector. Use a ... Maytag Dishwashers

Error code I keep getting an error code R02 on my Indesit DE 73 dishwasher, can anyone tell me what this means


... Indesit 24 in. DE73 Evolution Free-standing Dishwasher

What do the selt test codes on my Kenwood Dishwasher Mean?


... Kenwood KDW12ST3A Built-in Dishwasher

Asko diswasher Dishwasher will not get water. Lines all checked, water on. Pump runs even when in off. Problem started when there was a water clog in the sink next to the dishwasher, and the dishwasher backfilled with water. We used a shop vac to get the dirty water out. Next day tried to use dishwasher, runs, but no water and empying pump will not stop running. Ideas?


Check for water leaks or not draining/overfilling fault ... Asko D1776 Stainless Steel Built-in Dishwasher

Kenmore Elite Dishwasher stopped running and the clean light is blinking 6 times then once over and over again. What is the problem and what does the code mean?


... Kenmore Dishwashers

I have a Hotpoint FDW80 Dishwasher. The drain pump runs continuously, even though there is no water inside, I poured water in with a kettle and it does drain correctly. After a short while fault code AL01 appears. I have removed the base tray to check the "anti-flood" swithch and that is OK, even with the switch disconnected, I still get AL01. Any ideas?


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

LG dishwasher Model LDS5811BB Stops while running, displays code OE. What does this mean?


The most common cause of an OE error code on a modern LG dishwasher is: 1. Blocked drain hose 2. Obstruction in the sump area (beneath the filter, which needs to be removed to check for onstruction) 3. Failing drain motor. ... Dishwashers

We have a Hobart FXS 70N Dishwasher and it gives us a F04 error code. What does it mean and how can it be fixed? Where can we also get a wiring diagram for it? Thanks Engela


... Dishwashers

Getting error code 0E on LD-14AW3 model dishwasher after 2 minutes. Checked drain hose and water seems to be coming out but won'y go any further in cycle Also makes a loud humming noise when running.


To little info, but looks like pipe is much to low. Not getting the opportunity to fill up properly.Raise it higher.(Im asuming that you can hear the drain pump run and water is being pumped out as wall. ... Dishwashers

Asko 1585 Dishwasher. Lately the washer has not been completing it's cycle without going into the all lights flashing mode. Usually just opening the door, closing then pushing start gets it going again. Yesterday this happened and it was restarted as described, then it go stuck in what appeared to be a drain mode - all lights flashing, drain motor running. It was in this mode for several hours and could not be stopped by any means. Pushing buttons or opening the door had no effect. Even c


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa. You are right it is related to a bad control board. The\015\012control board has gone faulty and needs a replacement. Please check this recall\015\012information--- ... Asko 24 in. 1585 Built-in Dishwasher

Got a Miele G2220sci dishwasher unit, getting an undocumented error code of F19 with flashing lights, help! what does F19 mean? WONT DRAIN. PROGRAM FINISHES WITH F11


F19 is water in the cabinet takes too long to heat up. you can reset the heater limiter..\015\012\015\012Reset the error message as follows: To cancel the error message, turn the rotary selector switch to "Stop/End" or press the "Start/St ... Dishwashers

Hi My F&P dishdrawer flooded. Dried it all out etc, the top drawer doesn't complete the cycle and it beeps continually even when it's not running. I am wondering if I can reset the drawer using the front buttons to get it back to factory default. Bottom drawer works fine. There is no error code on the screen only the lock icon which won't go away. Any ideas?


Not sure if you tried turning the power off at the main switch. Lock icon can gone away if you press the necessary keys as shown in the user guide. Also the sequence of keys to press for getting factory defaults of different options is also in the us ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1959 seconds