Having problems with your Dishwashers ?

This a message for phil. The aquastop valve was not under the dishwasher. On my model, it was fitted directly onto the water inlet pipe. I replaced the valve as you suggested. After removing the old valve you could see through the clear plastic housing that water was leaking inside the valve. Anyway replaced valve but had to split wires and reconnect with connections supplied with the valve and according to instructions. Water leak has now stopped but when 'on' button is depresse


Answers :

Please provide dishwasher make and model. Looks like you are retrofitting the valve to your dishwasher which may not be getting the correct supply voltage from the dishwasher control. Will need to understand part no. of the replacement valve you have used before providing any further advise.
\015\012
\015\012Perhaps phil may also see this message and respond to you at some stage. Your message has been out there since 31st May.
Hi Brian.

Can you please state again the terms of the problem and please give us full model number. Unfortunately the Fixya system does not send the new questions always to the same expert and does not allow us to see each other solutions.

If you want to contact Phil, post an add on comment to your original post. He will receive an email notification. If you want to keep troubleshooting, please provide model number and briefly describe the problem from scrap.

Regards.

Ginko.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

This a message for phil. The aquastop valve was not under the dishwasher. On my model, it was fitted directly onto the water inlet pipe. I replaced the valve as you suggested. After removing the old valve you could see through the clear plastic housing that water was leaking inside the valve. Anyway replaced valve but had to split wires and reconnect with connections supplied with the valve and according to instructions. Water leak has now stopped but when 'on' button is depresse


Please provide dishwasher make and model. Looks like you are retrofitting the valve to your dishwasher which may not be getting the correct supply voltage from the dishwasher control. Will need to understand part no. of the replacement valve you ha ... Dishwashers

HI there dish washer wont fill Ichecked fill valve its ok but there is no 110 volt reading to wires but when i remove purple wire from water valve and put ground wire to fill valve water comes in the dishwasher please tell what needs to be replaced thanks


There may be problem with your door switch/lock mechanism,be sure to check the main power supply to the dishwasher.\015\012if you have a electronic control board it might also have to be replaced. ... Dishwashers

Dishwasher does not start it seems there's no water coming in the tub. I got a trouble shooting manual from ejunkie.com and tested the coil of the water valve which read 1000 Ohms, which means it's OK. Then I hot wired the coil while connected to the water line and the valve opened and I had water flowing [ in a bucket] I have tried to start the test program [hold power scrub plus and regular switch at same time then start button] and lights start flashing you hear drain pump come in then the un


... Bosch SHV4803 Dishwasher

Whirlpool Quiet Wash Plus dishwasher Model DU920PFGZ3. Worked fine until I replaced the insinkerator and forgot to punch the drain plug leaving water standing on the bottom of the machine. I punched the drain opening, and pushed the cancel/drain cycle button. It drained fine but since no water comes from the spray arms. I have removed the arm all the way down..NOTHING!! Some research indicated it could be the water inlet valve. When the buttons are pushed, it cycles but no spray or water.


... Dishwashers

BOSH DISHWASHER SHU5300: DOESN'T DRAIN COMPLETELY, WATER DOES NOT SIT ON THE BOTTOM BUT POOLS UNDER THE FINE FILTER. THE WATER HAS A BUILD UP AND THEN BEGINS TO SMELL. UCK!! I HAVE DONE ALL OF THE CARE & CLEANING POINTS FROM THE MANUAL. THE DRAIN HOSE DOES NOT HAVE AIR GAPS, THAT ISSUES WAS ADDRESSED. PLUS SEVERAL OF THE BUTTONS DO NOT WORK. THE BUTTONS DEPRESS BUT DO NOT FUNCTION. BEGINNING TO QUESTION IF I SHOULD REPLACE THE DISHWASHER? (10 YEARS OLD) THANKS FOR YOUR HELP!


Def replace .....time to put the old girl down ....whirlpool is a good choice ....or another bosh ... Bosch 24 in. SHU53 Built-in Dishwasher

No Power I have a bosch shx33 dishwasher. I just replaced the water valve because of a leak and now I can't start the dishwasher. It's like there is no power to the unit. I know there is power because I get a shock if I touch the two wires that are connected to the water valve. Is there another trip switch or something somewhere?


First let me say that using parts of your body to test for mains electriciy is a VERY VERY bad idea. You are lucky you are not dead. Please do not touch live parts again, get a multimeter or a mains tester.\015\012\015\012If there is mains across the ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Asko Dishwasher DW20.1 d3120 Water not coming through inlet valve. I have replaced the inlet valve - solenoid only releases when on/off switch and start button are pressed and released simultaneously. A burst of water comes out at that point and stops. What could be wrong?


Hi, Welcome to FixYa.\015\012\015\012I'll start by saying your description sounds exactly like a symptom of a faulty control board on Asko dishwasher's...specifically the relay responsible for energizing the fill valve. It sounds to me like the relay ... Dishwashers

I have a pot scrubber 600. I just replaced the water line. I had to disconnect the electric wire to service the unit. Everything is running except the water doesn't fill, and there is an awful buzz from the actuator for the water discharge. What is going on? The water valve is on but doesn't fill.


So tell...me...you replaced the water line why......its probably moot as to why you did it....just realize that the large majority of no water problems are due to a wire off or loose on a water solenoid valve or a bad solenoid....I am going to provid ... GE Dishwashers

I had a problem with my dishwasher popping the breaker. I opened the bottom and found burnt up wires. I fixed those and now the dishwasher stays on and begins its cycle (by draining) but the water is not flowing to the machine. It has supply, and I just now replaced the water inlet valve- no difference. The water was working before the breaker issue. I'm wondering if it is now something as simple as a clog somewhere since the washer sat unused for a month; or, if it is something more compli


I read your previous problem. This appears to be separate problems. The first was likely a loose wire. When a wire has a loose connection they build heat and can melt. The current issue would seem like the float switch is stuck. The float switch is ... Bosch SHU9925UC Built-in Dishwasher

Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???


Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher

Asko d3100 dishwasher still giving problems after replacing inlet valve. When you press the start button all of the lights come on and there is some pumping sound with a dribble of water coming through from the right hand side. When you take your finger off the start button everything stops, no lights, no pumping. Anyone got any ideas?


Hi.To start, disconnect power and ensure that there is no water in the tub when you restart the dishwasher.It looks like the overfill switch is preventing the machine from filling. The overfill (water level) switch is either a ... Dishwashers

My Karcher 330 M has blown two water inlet ( Garden hose inlet ) elbows. Replaced one and then after about 5 min operation shut off the valve on the wand and immediately the new elbow split the same as the first. The garden hose I was using has a shut off valve could this caude the problem?


I have a larger gas powered karcher, just make sure the water going to your karcher is not obstructed from its path. on mine i bought a goodyear hose that can be purchased at northern tools or any hardware store. and use it just for pressure washing. ... Karcher PSI Electric Pressure Washer

Whirlpool dishwasher, model DU1050XTPQ1, type 575-0; problem: showing no sign of power to unit and bottom of dishwasher is full of water---it apparently stopped during cycle. Is there a reset button? I have tried depressing the front panel "lock" button for five to ten seconds to unlock the system with no luck. The washer is hard wired to the home electrical system. What should be my next course of action? Thanks


... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Hotpoint fdw70 error code A10 have replaced the inlet water valve but still have an error code flashing A10 hoped to find a reset button but cant find it anywhere can u possibl advise.


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

Changing GE water inlet valve on dishwasher replacement part is shaped different how can I make sure I put wire connection back on the right way. Thank You


... GE GLD5800L Dishwasher

Samsung dmt800 dishwasher error code 4e. Water valve is open, pressure and temp correct, flex water hose not kinked, water inlet valve is free of debris. next steps? replace water inlet valve?


... Samsung DMT800RHW Built In Dishwashers

Miele 646 sc plus inlet tank solonoid valve on water tank leaking. We moved the machine from one room to another and now this valve is squirting out water. We replaced both door seals thinking that was the problem, then started the machine with a side pannel removed, and saw the jet of water coming from the solonoid valve on the water inlet tank. Any ideas.


... Miele Dishwashers

I posted a question about my Maytag Dishwashere MDBH945AWW not starting, all lights function, and got a response from you seen here in this thread http://www.fixya.com/ThreadView.aspx?thid=6123266&prdid=519913 I was checking the water inlet valve for a clog and have determined with a meter that there is only 25 volts going to the water inlet valve. I notice a blue wire goes to the float switch which I already checked, there are 2 black wires one of which runs towards the back and cant see where


Hi,No, the lights can be working and a relay on the board can still be bad. These things can be very difficult even for a pro to trouble shoot as there can be many things that possibly can cause a unit not to start.From what you are sayin ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

Our Kemore dishwasher is leaking water onto floor, and the water valve continues to pour water when machine was turned off, but is not leaking water now. There is also standing water at bottom of tub from running machine last night. Can I test to see if it is fill valve or the overfill float? Are these easily replaced?


You just need to clean the pump area in the bottom of your unit :)try to take spray arm out if you can and then open pump cover clean it good but watch for broken glass in it ...and thats it :) ... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

We currently replaced our water heater, after we replaced it all our water is running fine hot and cold, and i went to turn on my dishwater and no water is running, we checked the valves and everything is opened but when i opened it up it was heated up and no water was going through can you help!


Hi,Reach inside your d/w and jiggle the mushroom shaped float switch\015\012located on floor of d/w. should move freely up and down if its stuck\015\012up(or something lodged under it your unit wont fill with water)....Check a ... Asko 24 in. 1805 Built-in Dishwasher

GE model#vrb4119vw129 My water inlet valve wont stop pumping water after the tub is full. I have replace the water inlet valve and the float switch.


... Dishwashers

Bought suction hose for karcher in order to use water from bucket. Have attached hose but there is no water being sucked from the bucket . One side of hose attached to washer the other dropped in bucket is this right? The end in the bucket has no suction, and a depressable valve that seems to be impeding the water suction. Do I remove this valve ?


... Karcher 26408500 Pressure Washer 25Foot ExtensionReplacement Hose

I have a Bosch dishwasher that is about 4-6 years old (model SHU8805UC/U12). A few days ago I found clear water in the tub hours after the wash cycle had completed. I drained the tub by resetting the cycle as instructed in the user manual, but the tub gradually filled up with water again after several hours.. will replacing the inlet valve solve this issue?according to what I can tell for my model the water valve assembly (part No. AP3783031) is the part I need. How difficult and expensive


Just pulled mine out last night. You have a different model but it should be the same. Remove the bottom dress panel and detach your inlet hose from the water valve assembly (have a rag handy to catch a little water). Two torx screws on the front ... Dishwashers

Frigidaire built in dishwasher model PLD2855RFC1. Have to wash dishes pretty much spotless prior to using dishwaser. Glasses come out with what appears to be soap residue regardless if powder or liquid. Did not use a gauge but water pressure in rest of house is good, recently replaced water heater, pressure regulator and just replaced the dish washer water source valve. Washer is about 18 months old, has never worked really well.


Hi, \012\012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and ins ... Frigidaire PLD2855RFC Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1222 seconds