Having problems with your Dishwashers ?

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Answers :

Hi,
\015\012
\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.
\015\012
\015\012http://tigerdirect.partsearch.com/GetModel.aspx?MfgName=Whirlpool&BrandName=KitchenAid&ModelNumber=KUDC03IVWH&page=1&SortBy=brandname&SortDirection=asc
\015\012
\015\012Thank You for contacting Fixya and please accept the solution if it has helped you.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

My ariston lsv 66 dishwasher will not start washing cycle. It makes the pumping noise as it normally does at the start of the cycle and some water enters the bottom of the machine but then it stops. I have checked to make sure that there are no leaks so the problem is with the filling up of the machine. I live in a hard water area and haven't used anything to help reduce the limescale so expect this to be playing a part. I have tried all the washing cycles but the same thing happens. Any advic


HERE I AM I LIKE THIS JOBE\015\012 PLEASE CHECK THE WATER INLET FILTER I FEEL FROM YOUR DESCRIBE IS IT\015\012 YOU NEED TO CLEAN IT BY ASMALL BRUSH >\015\012 THANKS ... Dishwashers

My Baumatic BWD 1631 will not start unless I close the door, hold down the programme button, press the on/off button, release the programme button, at which point all 5 programme indicators light up. If I then press the programme button again, the lights then all intermittantly cycle. However during this period, the bleeper sounds, the water inlet valve works, the circulating pump works and finally the discharge pump works and the machine empties. However I am unable to stop or start the machine


... Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

My 1yo slimline hotpoint dishwasher LST216 has developed a fault when trying to run the 'normal wash': washing stops after a couple of mins, the lights start flashing and the alarm comes on as soon as the water is being drawn into the machine. When I open the door I can hear a whirling/grating motor noise coming from the bottom of the machine. I have cleaned all filters and have run other programmes to check overall functionality and they all work as expected most of the time. I cannot unders


... Hotpoint Dishwashers

I pressed the POWER button to turn on the dishwasher. I pressed the SELECT button, hit HEATED DRY button and the LIGHT WASH buttons. I then hit the START/PAUSE button to start the cycle. All lights came on as normal & I heard the machine trying to **** up water like it normally does. Within 5 minutes or so, the machine started to BEEP & BEEP every minute. When I came to the check why the beeping noise was on, I saw that all the WASH PROGRAM lights were all blinking. I hit the START/PAUSE


... Haier ESD210 / ESD211 Built-in Dishwasher

After starting dishwasher to do a normal wash with heated dry, the dishwasher stops and Clean light blinks 7 times, pauses and this continues until I reset the machine. After reset it goes to rinse only and goes for a minute or so and stops.


Hi\015\012\015\012Please check if the clean light is blinking 7 times. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If yes, then it is a water heating fault. To reso ... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

I have a Kenmore dishwasher, model 665.16039. Over the past month (we were on vacation 8 days over Xmas, but I assume it would have happened then, too) it has required rebooting using the Normal Wash - Heated Dry reset about 4-6 times. It would then do a couple loads okay, then need resetting. Now, however, it's refusing to reset to a point at which the Start buton will work. When I reset it, it flashes all the lights (incl. Start), and it fills, sprays, empties, etc. just as though it works


Make sure there is no water damage. ... Kenmore 24 in. 16039 Built-in Dishwasher

My Maytag MDB7609awb2 dishwasher has a glitch When I try to turn it on the heavy and light was lights go on but won't start the normal wash light won't go on at all until I keep pushing the off and on for a while, then suddenly the normal button works and start will start the machine, then is washes without any problem.


... Maytag 24 in. MDBH955AW Built-in Dishwasher

Whirlpool GU2300 Dishwasher. The machine stops for long periods during the cycle. All lights go out. If the machine is opened before the cycle finishes, it will not resume. If I try to restart, the normal wash light begins flashing. If I then try to cancel, the canel light and the normal wash light flash.


I have reviewed your problem with the Whirlpool GU2300 Dishwasher and have the fallowing suggestions for you.\015\012First, unplug the power to the unit and let it sit for a few minutes. This will clear all internal error messages ... Dishwashers

Hi, I have a zanussi DE6744S. I can select any program and water fills as normal. The problem is that the cycle runs and runs and dosn't stop unless I turn the machine off. When I restart the machine it just carries on until I press the current program button in for a about 10 seconds and the program stops. On the odd occasion it ends normally on the economy cycle (30 mins) but its pot luck. It does wash as normal but dosn't seem to get past constant washing (no drying) . Hope you can help, S


... Zanussi 24 in. DE6544 Built-in Dishwasher

My Kenmore Dishwasher 665.16359301 quit working. I flipped off the breaker then back on again. The cancel light comes on and it sounds like its going to drain but theres no water in it. After about 20 seconds it stops and the normal wash cycle light starts blinking. Thats it. I did the reset procedure and it started to work then went back to the normal wash light blinking.


... Kenmore Dishwashers

"Quick Rinse" light blinks constantly, unable to select "start" unable to select "normal wash" sometimes can select "pots and pans" but still not able to start. Was working normally, when it stopped at end or pre-rinse to start the main washing cycle, the "quick rinse" light came on blinking, and no other button works except as described above. Thanks,


Hi,\015\012 \015\012Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow ... Dishwashers

I have a haier hdw300 and when I turn it on after a very short time the intensive and normal wash cycle light indicators start flashing and the machine stops. Does anyone have a solution?


... Dishwashers

KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher: Just stopped working before Christmas. I had washed a load a day before, and the next day I couldn't use the Rinse Cycle. The lights turn on for Normal and Heavy, but nothing happens when I press Start. I played with the breakers a couple times, to try to "reset" the machine, but it didn't do any good. I really don't want to be spending a lot of money on that dishwasher, especially after reading all the horror stories abo


... KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher

Model: Whirlpool ADP 4501/5 (4 years old) Problem: Dishwasher won't start wash cycle. Green light flashes 11 times. After adding a bucket of water to the dishwasher it runs normally. Checked the inlet valve and it appears to be fine. Filled the salt container and it solved the problem for a while but having the same problem again. Any suggestions would be appreciated.


... Dishwashers

Candy washing machine runs through programme and stops at the point where it drains the drum to start the spin. Have switched it off and turned timer to correct position and it drains and spins OK (1200 spin) Tried other programmes on timer but same thing, stopping at point where the pump drains and the spin starts. Have checked the pump and is OK any ideas please, I am quite capable of taking the machine apart for repair. Thanks in anticipation Pete


... Dishwashers

Washes for 5 seconds then stops, then starts again intermittently First the heating element started to turn on during the cycle. I never used it before. I changed the setting to unselect Hi Temp Wash but don't remember if it was selected before. The next day the dishwasher filled as usual, washing started for about 4 seconds, then stopped for aroud 10 seconds. The start/stop cycle repeated about 4 times, then all lights went off and nothing more happened.


Bought a new dishwasher... ... Maytag 24 in. MDB7650AW Built-in Dishwasher

Pots/pan light blinks alternately with the normal wash button. Sometimes the cycle will start and then the lights come on. Once they start blinking, the cycle stops and I can't get it to start again. Unplugging it for a few days has worked a few times. But it just keeps getting more frequent. If it does start up, it heats fine and washes perfectly.


... Whirlpool DU1055XTSQ Built-in Dishwasher

Dishwasher DU1100. Odd behaviour during cycle: "Washing" light goes off and sound of washing stops. "Normal" light starts blinking and "soak and scour" light comes on (it was off before). No sound from washer. This persists for at least 10 hours. After that, the lights go off. Is this normal behaviour? It would appear tha the drying cycle did not go.


No it is not normal. It appears that either the membrane switch pad has failed or the control board has failed. ... Whirlpool Dishwashers

We have a Whirlpool ADG 7560 dishwasher which has recently started playing up. When switched on for a normal wash, after a short time the machine starts to beep. If you open the door the green programme light is on the pre rinse and the start light is flashing. After starting the cycle the few times eventually it works normally. Have cleaned all the filters etc.


... Dishwashers

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

The standard procedure to start the machine is to select a cycle (normal, dry heat, etc) then press the start key. Currently when I select the cycle and the cycle LED is on, pressing the start key does not start the machine. I can press cancel, then start and then choose the cycle and it will work. Also, if I first press the start key, the machine will start and the previous wash cycle selection LED will light up and that cycle will run. Do I have a problem with the keypad or the con


... Kenmore 16632 Built-in Dishwasher

Kitchenaid KUDP01FL : Hi, machine will start to fill (on heavy), and then will not engage into the wash cycle. Have to press cancel to drain water. All other settings ( china/rinse/ normal wash) when button is pressed and door closes will "click". No water fills into machine. Have to press cancel to end cycle. Can it be a bad connection being i tryed trial and error and banged on inside of door to maybe "fix" it. NOW, heavy cycle does not fill with water, just a "click" noise. Thanks for


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Unable to start dishwasher, only functioning light on the panel is the cancel/drain light. push that button the machine funtions for a minute or two and shuts off,also the light above normal wash is blinking. When the machine last functioned it would start with a very high decibel level.If its the circuit board I need an approximate replacement cost. Bob


If you go to searspartsdirect.com you can get the exact cost of the module. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2034 seconds