Having problems with your Dishwashers ?

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Answers :

Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will cause the code to appear, even though it is functioning(opening and closing). With that said; if the assembly is clear of any blockages, This will lead to a main control sector fault. replace the main control device, in this case.

Normally, if the vent has totally failed, you will get a "uf" code. Check for blockages in the assembly and replace the main control device if no blockages are found inside the vent assembly.


You can also test the fan, as well. Follow the procedure to achieve this below:

You will need a multimeter to test properly. Once you have gained access to the vent motor terminals;Set the multimeter to the ohms setting X1. Touch one probe to each terminal. You should get a reading of zero. If the fan fails this test, the vent assembly must be replaced.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Frigidaire dishwasher keeps showing the Er uo codo on the display. It used to would finish a load even though it would stop for a while when the error message came up, but now it will not run at all when the error message comes up. I read on this site that the Er uo has to do with the vent. I pulled the dishwasher out and removed the vent. I turned the dishwasher on and the vent opened and closed about three times when the cycle started, then it stopped and the error message came up. Is


Hi. This code is in reference to the vent assembly. This may also be a control fault, as well. To isolate the culprit, you will need to make sure that the vent assembly is not blocked. If it is blocked, it must be replaced. Restricted air flow will c ... Dishwashers

Zanussi ZDF 511 S dishwasher not draining. Shows error message '20'. Cleared filter, removed hose from usual drain and restarted cycle. Still not working - same error message. Any suggestions would be helpful. Thank you. Myles


... Dishwashers

DS603 Fisher & Paykel U1 error code ..(see our previous errors we've listed) we have now pulled out the yellow water valve that goes up behind the front panel and at the other end by removing the drawer and plastic protector thingy - we checked that there were no bedris or calcium buildup in the valves ends and filters and replaced it all. So we put it all back to gether as we could not see what would cause this error, only to find that it worked - water came into the machine but about 4 mins in


This product is total ****.\015\012Pull it out, call whoever sold the **** to you\015\012and tell the to come get it and shove it up their ***.\015\012Then buy a Bosch and live a happy life.\015\012The design is moronic. The machine is like the old\ ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

I have a Frigidaire 4000 Series Dishwasher, Model# FDB4315FCO, almost six years old. It acts as if there is no power. There is no error code. If I pull the power cord I get a "PF" message.


... Dishwashers

I had a black out and the dishwasher was running at the time. The dishwasher emptied out all over the floor. when the power came back on the dishwasher was flashing an error code 4. I rang Whirlpool for assistance and they said it was over full but it was totally empty. We turned the dishwasher off at the wall hoping it would reset but it is still saying error code 4. Can you suggest something else we can do?


The trouble looks to be little confusing. Whenever the power failsduring mid cycle this happens. Try running the balance cycle. Since you say the water is fully drained, try adding water manually tothe wash chamber to certain ... Whirlpool Dishwashers

When I replaced my garbage disposal I forgot to remove the knockout tab that would have allowed my my bosch SHE58C05UC dishwasher to drain into the disposal. I discovered my error the first time I ran my dishwasher and discovered that none of the water had drained. I then removed the knockput plug and reattached the drain line. My dishwasher now drains correctly but makes a loud sound whenever the pump turns on. Have I ruined my pump or is there something I can do to eliminate the loud noisy pum


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thank You for using\015\012FixYa. To start with check the pump and try to clean it out, then check drain\015\012hose for any obstructio ... Bosch Dishwashers

Dishwasher adp6000 shows error message 4 - meaning over filled. Have removed filter and drained bottom area. Now will not stop showing error message.


... Dishwashers

Dishlex global 450 _ how do i fix fill level time fault? displaying oF? Hi There, I have the above dishwasher and saw your advice on fixing fill levels - my display is showing the oF message and the pump to drain remains on whilst mains is connected. turning off mains does not clear message. holding eco button down does not clear message? is there anything else i should do in terms of removing parts to assist the process? I have cleaned out all of the drainage bowl and all is clear. i would pref


... Dishwashers

IE message Getting an IE message on dishwasher. Water is coming into the tank and heating, but after about 5 minutes, it kicks into an IE error. We have checked the water inlet and the spray arms and everything appears okay. I have read the comments about checking the float, but how do you do this? Any other suggestions would be helpful.


My solution was, after LG sent me a second dishwasher that ALSO did not work, to demand a refund. Then I went and bought a KitchenAid~ it's awesome! ... LG LDF6810 Built-in Dishwasher

After working perfectly for years, I came home yesterday and the dishwasher had gone through it's whole cycle (including drying) but the bottom was fully filled with water. I emptied the dishwasher and tried to put it through a "rinse and hold" cycle to see if it would drain, but that didn't work. I pulled out the filter--it's clean as a whistle. Any thoughts? PLEASE?? thanks!


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Water will not drain out ... Bosch 24 in. SHY56A05 Stainless Steel Built-In Dishwasher

We getting the error message LE on the dishwaser model #LDF6810ST. The repair Official repair man that came out to supposedly fix the dishwasher called LG to find out what was wrong with it and they told him to tell us that we need to replace the motor and wiring harness and the Technician told us to order the "motor and wiring harness" charged us $100 and left and the dishwasher that is only 2 years old and we paid a little over $800 for is still broke. Now when trying to order the "motor and w


Motor assy pn# 4681ED1004A is the motor you will need. ... LG Dishwashers

I have a dishlex global 500, will not draw water in, comes up with error code nf. I have taken all hoses and filters apart, cleaned them, still no luck. I cannot find a blockage. ps, the dishwasher tripped my power off , then error message came up when I reset power


... Dishwashers

Kitchenaid kuddo1dppa I own a KitchenAid KUDD01DPPA, 2 drawer dishwasher. I am not a technician, however I have had a lot of experience in repairing various appliances and am savvy with electronics and mechanical technical issues. Here's the problem: I was getting rinse error codes in both drawers, pulled the bottom drawer out, removed the cover to the circuit board and used a dryer to dry up the moisture on the flood switch. Now I am getting Fill Failure error code on both drawers. I have g


Test this steps and fix it. God bless you\012 \012 Water Inlet Valve\012 \012 \012 \012 \012 \012 \012 \012 \012 ... Dishwashers

ASKO dishwasher my dishwasher came on spontaneously and keeps running first (drain, I believe) cycle. It stops when I unplug it (of course- no power) but sturts immediately when I plug it back. Error message is displayed


F2 fault water in the base remove dishwasher from under the bench and tip back water will run out,then it will restart.remove rear lower panel and run the dishwasher you may find a leak,also check that the inlet valve is shutting off and not filling ... Asko D1776 Stainless Steel Built-in Dishwasher

Purchased ge dishwasher model ghda674n00bg and discovered after installation that I removed the rubber check valve from the discharge line in error. Is it mandatory that this check valve be installed? Naturally I would prefer not to remove and reinstall unit. Thanks for your help Regards, John


... GE Dishwashers

Dishwasher Model Kenmore # 665 16829000 Dishwasher "Quick Rinse" was blinking and no other buttons would work. Received FixYa solution below: "Check out the console assembly. take off the inside cover and the plastic over the electronics, just remove the two screws holding down the circuit board, pull it to the side, then blow plenty of air through the two holes on either side. The holes that you need to blow air into are not on the circuit board, but on the plastic underneath the circuit boar


Hi\015\012If the control board detects that a key is stuck in the depressed position, the dishwasher operation will be suspended and the control will flash the light for that key until the condition corrected. If a key without a light is ... Dishwashers

ASKO D1976 model. We have a F2 error message. Water has now been drained but we are unable to remove error code or have dishwasher return to normal cycle


Display shows an error code. Do the following:1. Unplug washer or disconnect power for one minute. 2. Plug in washer or reconnect power. 3. Re-select the cycle and press Start.NOTE: If the error remains on the disp ... Dishwashers

LG dishwasher LDF7811ST, LE error message


Http://cgi.ebay.com/NEW-LG-DISHWASHER-LDF78 ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

E3 Error Hi My dishwasher is showing error E3, which the user manual states "The appliance is not able to pump out the water.", however, other E3 error states a heating issue. The dishwasher does in fact heat the water but generates the E3 error after 10 minutes or so, then pumps out the water from the dishwasher. I'm a little confused as to what the issue is here and what part I would need to rectify the problem. Any advise you could give would be greatly appreciated. Kind regards


The E3 error is a result of water temperature not getting to a nominal value within a particular time. This could be caused by several factors like heater faulty, wash pump not working well, wash arms not circulating water as required. Need model nu ... Smeg Dishwashers

LG LDF8812ST dishwasher not washing: reports LE error code. Fills and drains ok. Impeller is clear, removed inside housing - no obstructions. Synchronous motor works. Tested main motor - appears to be good. Motor is not locked, looks to be in excellent condition. No shorts to ground, continuity across three main pins - not sure what the other 4 are for. My guess would be the PCB, but not sure how to test this. How do I determine if the PCB is bad?


... LG LDF9810ST Built-in Dishwasher

Dishwasher is a SAMSUNG - The ERROR message was E5, hose kik/drain issue. Even after removing and inspecting hose, plus flushing drain line, not fixed. It does drain through the hose with wetvac suction.


All the above are correct and will give you an 5E error on the Samsung DMR57LFS. Do this... fill up a small pot of warm water and dump it into the dishwasher (the sump will now have water in it). Turn your machines power on and look in the sink (the ... Samsung DMR57LFS Stainless Steel Builtin Dishwasher

I have an E3 error message on m SMEG STX1 dishwasher. I've cleaned all pipes so am fairly sure that the heating element needs to be replaced. How do I access the heating element to test it? If there is a procedure for taking apart I would be very grateful indeed. Type 10031 model no 1471588673


Hi.E3 means that there is a problem with the heating system. The problem is either heating element or thermostat. The heating element in SMEG dishwashers is usually located underneath the appliance (in some model is at one side or at the ... Smeg 24 in. STX1-1 Free-standing Dishwasher

I have a SMEG DWF614 SS dishwasher. I continue to get an E8 error message. The diverter valve motor turns freely & the motor turns freely when they are seperated. However, when they are assembled, the motor turns the valve & continues to try turning the valve when the valve is on its stop position. Is the motor & valve faulty or is it the control. If you can answer, what part number would I require. Regards Leighton Davies


... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher

"PE" error message on LG Dishwasher LD-12AS1 LD-12AW2


The PE error code indicates that the machine has a water pressure sensing error.\015\012Check and clean the filters on both sides of the inlet water line.\015\012Good luck! ... Dishwashers

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1938 seconds