Having problems with your Dishwashers ?

Dish machine My dishwasher is clogged,it has standing water when cycle is complete. older kitchen aid machine and my garbage disposal is also running very slow thru the kitchen sink. thank you


Answers :

You need a plumber sounds like your sink piping has a blockage
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dish machine My dishwasher is clogged,it has standing water when cycle is complete. older kitchen aid machine and my garbage disposal is also running very slow thru the kitchen sink. thank you


You need a plumber sounds like your sink piping has a blockage ... Dishwashers

Hobart lxih everytime i add soap i get a service code e4 and the machine stops shut the machine off and it restarts just fine add soap and shuts down i use a powered saop made for under the counter dishwashers even when i run a delime agent thru the machine it the does the same what to do thanks for help david


E4 indicates water level has not reached top water sensor. Check for proper flow-water pressure to machine (15-25psi) and clean sensor in wash tank ... Hobart 24 in. LXIH-3 Built-in Dishwasher

DWI410 Thanks for your help Tresilla. Unfortunately, no such capacitor evident in my machine. Do you think that a smeg technician could successfully run a diagnostic check? I'm reluctant to throw the machine away, but I also don't want to pay a lot for a visit if there's little chance of him/her finding the problem.


There will be a capacitor. usually attached to the motor but sometimes mounted at the back. it is a cylindrical object about 3-4 ins long and about 11/2 ins diametersmeg tech should be able to find the problem but will be expensive ... Smeg 18 in. DWI410 Built-in Dishwasher

I have a GE dishwasher model # PDW7880. The dishes are not clean even after running the dishwasher for two cycles. Also, the soap often doesn't dissolve. There are no dishes blocking the soap dispenser so I'm not sure why this is happening. In the manual, it says the air gap or disposer is clogged. Where is the disposer? Thank you. Sue


I had the same issue. I discovered that the spray arm at the bottom and the one under the top rack were both clogged with debris. I removed them both and after 20 minutes of running water down them and poking with a paper clip, I got all the stuff ... Dishwashers

We have a Diplomat dishwasher ADP 8242 and its intergrated but have no manual, the machine switches on fine and starts its cycle, i switched it on before going to bed and in the morning it was still running so obviously knew something was wrong, when i opened it the dishes were not clean and there was water in the bottom which took a while to drain away, also the salt inlet is full of water, should it be like that? Any advice would be great thank you.


... Dishwashers

The dishwasher is cutting out the mains rcd switch when running? This happened during an intensive wash now as soon as you switch the on switch it trips the cut out! I have checked the both pumps for earth or neutral leaks and also the the heater but all seem fine. I only have a multi meter at my disposal so therefore cannot do a proper earth leak check. the machine is approx four years old and is not used very often.


Hello, dawhI\012 was trying to help you out here. I am not sure if this well help you? \012But here is a link to about everything you want to know about your \012dishwasher, from repair to trouble shooting on most common dishw ... Zanussi 32 in. DE6755 Dishwasher

I have a new FDB520RHS2A Frigidaire dishwasher which remains in the wash cycle after I've started it. It sounds as if it is changing cycles but the wash light stays lit and never switches to rinse. The machine continues to run for hours if I don't stop it. We've checked the drain to the garbage disposal and it is clear. the water temp seems to be hot enough but how do I check that? Any ideas on what we should check before we bring it back to the store? Your help is much appreciated. Thanks!


... Dishwashers

Water remains in the bottom of the diswasher after the cleaning cycle has completed. We recently had a new kitchen faucet and garbage disposal installed. The dishwasher also hums during the dry cycle, I never noticed this before. Are these problems related? Do I need to get a repairman out here to fix the problem or can I do it myself? Thanks, Robin Pomazal Naperville, IL


... Maytag MDB7609AWS Builtin Dishwasher

Have a Karcher kb4040 that continues to run constantly even when the trigger isnt pressed. Also water flows out of the detergant hose when im not pressing the trigger. Pressure seems down slighlty, not much. This happened after i ran water out of trigger gun with no lance attached, machine switched on. Seems to leak from trigger handle aswell. Many thanks in advance


This is two things. One is the back flow check valve to the soap line is leaking. The other is the pressure switch on the output side of the pump. ... Pressure Washers

Hi i have a technik dishwasher it has flooded the kitchen, i managed to get all of the water out of the machine but now the pump seems to be running all of the time, someone has told me there is a flood switch on the wachine that will need re-setting but i can not find it can you please help me please either email me or ring me on 07875666327 uk number. many thanks chris


Drain pump is running all time because there is water in bottom tray. tilt machine back to 45deg and water will flow out. otherwise, take front panel off and mop water out. alll that is required to reset flood switch is to get rid of the water ... Tecnik Dishwashers

I have a GE Dishwasher: PDW8480JO1SS and it does not fully drain when I run it. I disasembled it and after finding a carrot deep in the pump area thought I had fixed it, but no luck. I also made sure there were no obstructions in the drain out to the disposal. Tee unit is about 6 years old. I don't know if I need to replace my pump or motor? Can you help? Thanks, Mark


... Dishwashers

Kitchen Aid Dishwasher KUDR24SEBLO does not drain 100%. I have removed the drain hose and chcked the sink P-Trap, [it drains thru the garbage disposer]. Unit is 10 years old, otherwise works fine. I am having difficulty removing the impeller and items above the pump to see if it is clogged. Do you think I have a partially clogged pump or a timer issue that prevents the pump from completely emptying the bottom of the dishwasher? We have run the dishwasher 20-30 times since observing the problem.


Hi there,\012Please check out the following -Pump - Your dishwasher pump ejects the water. The pump is usually mounted directly to the motor, then attached to the bottom of the dishwasher. You can reach the pu ... KitchenAid Dishwashers

My karcher hds 745 is running but just won't build up pressure, this occurred after a really cold few weeks this winter and I hadn't put anti-freeze through the machine to winterize it. There's no water coming from the bottom of the machine when it's running as i've read that if the pump seals are faulty water will escape from the pump etc. The machine motor runs ok but no pressure is acheived on the gauge whatsoever. Any help would be appreciated. Thanks in advance Paul.


... Karcher Pressure Washers

What makes swing on bobcat 337 slow?filters news oil new and full has good breakout power but everything seems to be slower that other machines i have run or owed my case cx 50 would eat this machine alive the bobcat isnt mine but run for a township i work for. very disappointing machine. has 2500 hrs on it any ideas bad pump or valves it


... Pressure Washers

We have a problem with our Miele G851 SC Plus dishwasher. We have not operated it for over three months as we were away on vacation and also because there were other issues in the kitchen due to some water flooding . Yesterday we switched on the machine and notice that the machine flashes the intake / drain light after a few minutes into the cycle and stops working. we have checked the drain pipe for blockages and also the water pressure is good. I disconnected the machine drain from the


Www.miele.ca/miele/canada/OperatingInstructions/.../G851%2005431311.pdf\015\012\015\012\015\012\015\012 ... Dishwashers

Our dishwasher came with our house. Brand new. It is 2 yrs old now, warranty gone. The problem is when you shut the door the machine starts running immediately and keeps running and running and running. You can push the stop button, delay button and it still runs. Also, doesn't clean. model# FDB1050REC4


... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Dish Washer, Electrolux Home Products, Model FDB2510LCC0, Serial NO: 7H34962223 Machine does not drain or add water. The machine has been worked for a couple of years. I checked the following: 1. Overfill Protector not stuck 2. Motor turns on and the machine cycles correctly 3. Since the machine has been running correctly the unit is hooked up correctly: hoses, garbage disposal, knockout plug. Again everything has worked and the motor does cycle and the machine will perform the different cycles


... Electrolux 23 in. ESI602 Free-standing Dishwasher

I have a craftsman Pressure washer Model 580-725400 the unit has ran great until today. I last used the unit 1 week ago with no problems but now I have to run the machine almost full choke to get it it rev up and run smooth. The engine oil is clean and filled to the proper point. The spark plug is new and gapped proper. The air filter is new also. And the gas is 97 Oct and fresh. When it choke it to crank the engione I move the choen to run and the engine struggles to run. When I move the choke


... Craftsman Pressure Washers

Electronic controls the dishwasher will not turn on. press and hold the heated dry button for 5 seconds and the machine came back to normal. now even that is not getting the machine back to normal. the normal button and start buttons flash but machine does not function. i have the front electronic panel off and do have a volt meter to test if you could run me thru the proper procedures.


First thing to check is the door latch switches, and hte strike plate(metal tab protruding from the top of tub assy in which the door closes into, if bent up to high the door will not be recognizedas being closed. you can use a small screw driver nad ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

We installed a Samsung DMT 300 and gave it a test run. All went well. The next time the lady used it it would not pump water into the machine. We went back and checked and there is water to the machine but it will not go into the machine. Any ideas? Thanks.


... Samsung Dishwashers

I have a Kitchen Aid dishwasher. IC Series. Model # KUDN230YWH. The dishwaser fills and runs but it does not cycle past that. It will run until we shut it off. I can hold the button in and it will click and to get it to the drain cycle and it will drain but it will not do it on its own. It just fills and runs. Thats it. Thanks


Hi\015\012\015\012Thanks for using FixYa. If the cycle doesn't\015\012complete, then the first thing that should be checked is the Timer and then the\015\012heating element. Timers don't often ... KitchenAid 24 in. KUDP02SRSS Stainless Steel Built-in Dishwasher

Hi I have a Neff built in dishwasher s5453X1GB/70 about 4 years old. Never had a problem before. Came downstairs last night to find the kitchen floor flooded. Water also still in machine. But must have been near end of cycle as plates all clean. I have read other links and opened pump compartment in centre of machine and syringed out all water and cleaned fan. When i switch on machine it is still making odd humming noise (emptying cycle?) I have read about anti -flood valve etc. Any more tip


... Dishwashers

Kitchen Aid Dishwasher - model: KUDPO2CRBLOrn Ran the dishwasher twice on pots/pans cycle and sani rinse with a special cleaner recommended due to build up and items not getting clean. (soap left all over them) Cleaned machine out great! Now, the only choices that will light are "quick clean up" and "rinse only." Even if I choose them, when I hit the "start" button - the machine will not start. No other lights will light. Machine will not start. Any ideas?? Thank you!!!


... KitchenAid Dishwashers

The standard procedure to start the machine is to select a cycle (normal, dry heat, etc) then press the start key. Currently when I select the cycle and the cycle LED is on, pressing the start key does not start the machine. I can press cancel, then start and then choose the cycle and it will work. Also, if I first press the start key, the machine will start and the previous wash cycle selection LED will light up and that cycle will run. Do I have a problem with the keypad or the con


... Kenmore 16632 Built-in Dishwasher

My dish wash machine (HOBART FX/CV series) is programmed to PO1 and it should be running for short cycle but what's happening is it keeps on running for a long time...please help..many thanks..


... Hobart 24 in. LXIH-3 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1289 seconds