Having problems with your Dishwashers ?

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


Answers :

I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the water drained, but no new, clean water came through the hot water pipe. The drain just kept running, but nothing else happened.
\015\012
\015\012Here's what happened. Under the main chamber of the dishwasher, by three inches or more, is a white plastic tray. It sits almost at the floor, and it may not be obvious that it's a tray capable of holding water. The overflow water spilled into that tray, which in turn caused a float in the far left side of the tray to lift (the way a toilet float lifts when the water fills in a toilet tank) and shut off the water intake valve (like the toilet float shuts off the toilet water flow). So long as that valve is closed, your machine will not run.
\015\012
\015\012STOP: disconnect power supply at this point for safety.
\015\012
\015\012To see the white plastic tray and thereby fix the problem, you'll need to take off the BLACK TOE-KICK (attached on my unit by two star-head screws at its bottom) and, possibly , the OUTER PANEL OF THE DISHWASHER DOOR (in my case, a custom wood panel (attached by a few screws through the inner side of the door, two screws that are accessed by popping off little--smaller than a dime size--covers on the sides of the doors, and then the door panel lifts up and out). (I took the outer panel off, but I can't remember if I would have had to reach into the white tray without doing so.)
\015\012
\015\012Once you do that, you can see the white plastic tray. It doesn't come out--at least not without removing the entire machine--so try this. You can take your fingers and feel over and into the tray. You'll probably feel the water--I did. Look at the far left of the tray with a flashlight. Back there you'll see a flat, round, 3-inch diameter piece of white plastic sitting at the bottom of the tray. To its center is a generally U-shaped lever looking device, which, at its far left end, is connected to a red stick pointing up into the machine. When water goes into the tray, the float rises, causing the U-shaped lever to rise, causing the red stick to raise, which (though I couldn't see it) causes an electrical signal to run to, and shut, the valve for your water intake.
\015\012
\015\012I took paper towels, and then a narrowly cut sponge, to sop up the water in the tray. I then took my shop vac and, using it as a blower, blew what little water was left right out. You might be able to use a hair dryer, but first sop out what you can or it'll take forever. Once you've done that, put everything back together and plug your dishwasher back in. My buttons are at the top panel. To reset, hold down the two buttons marked for clear drain for three seconds and release. You should be able to start up then. It took 15 seconds before the water started to run, but it did and the machine works fine again.
\015\012
\015\012Interesting note: The valve that stopped the water from flowing in automatically opened once I got the water out of the tray. You don't need to reset the valve.
\015\012
\015\012Good luck.
\015\012
\015\012Montpelier Man
I am having a similar problem with our Dishwasher, although not the same model, they all have the same basic principals for operation.\015\012We have a Bosch SG13002GB/10 which is fitted with, what Bosch call "AquaStop"! This is a safety feature built into the base of the machine for the unlikely event of the unit developing a leak.\015\012There is a sealed chamber under the machine fitted with a float, when a leak occurs the water is channeled into this chamber where the float, when activated, cuts off the inlet water supply valve. In the event of a leak occuring during a wash cycle the drainage pump will continue to run even when the cycle has finished to ensure the machine is completely empty before any repairs are carried out.\015\012Check the operating manual for your machine to identify whether or not it is fitted with this feature.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

Smeg df612 dishwasher problem, lights up as a e2 fault ,i have tried draining the dishwasher but still the same problem . the salt container is full of water is this normal?. and how do i reset the machine . ive tried pressing the programme button 4 times but it just shifts through the different cycles . can you help please/.


... Smeg Dishwashers

Just purchased an Omega DW501WA dishwasher and after the 2nd use it stopped and the the 2n light from the right is flickering and the machine does not continue its cycle. The water is still remaining at the bottom and is not pumped out. Have tried to reset several time with the reset button on the front panel, but to now avail. Please advise of any possible solution. Thanks


I am having the same issues... ... Dishwashers

Defy dishmaid dishwasher does not start wash cycle. Several attempts to reset dishwasher has been done. Machine has been unplugged for several days and switched on again and still does not work. The start/stop switch have been kept in for about 5 - 10 seconds to reset. When the machine is set to do washing, the water enters the machine and wash light shows green and machine remains like that with water inside the machine. The start/stop button is again pressed for 5 -10 seconds to drain the wate


... Dishwashers

My Miele dishwasher (G 856 SC) is about 9 years old and has begun stopping in the washing cycle. The pump still drains the water when I reset but it no longer finishes the wash. Any ideas other than to replace the machine! I have tried restarting and cleaning the bottom large filter (both of which used to work) Thanks


... Miele G892SC SS Dishwasher

Dishwasher stuck on rinse cycle. Have three yo son who plays with buttons, but I've been unable to get washer to finish (rinse went for three hrs prior to me realizing it was still running). Tried the front panel buttons w/o effect other than able to turn unit off, but it resumes in rinse cycle. Turned power off to machine from circuit breaker ( w/ machine off) then restarted and still in rinse cycle. How do I reset?


... Miele G892SC SS Dishwasher

Bosch Dishwasher SHV4313GB/17 Wont switch off ! The machine keeps running even when you open the door The pump is trying to drain water away (even though there is no water left in machine ) Have tried to reset it as instructed but to no avail. It has beeped like it has finished cycle but the pump wont switch off HELP PLEASE !


Introduction: This may work for your problem, but only if you're finding that you cannot get further water to flow into your machine. If your machine fills OK, then this ISN'T a solution to your problem. If your machine doesn't fill but your drain m ... Dishwashers

My dishwasher (kleenmaid brandt super silent DW121TB) appears stuck in a wash cycle; how do I reset the program? I have read the instruction book to no available, tried unplugging power overnight, tried a combination of simultaneously holding buttons in and switching on, letting the machine run all night, drained the water and added clean unsudded water, and none have corrected the situation. There is also a selection lever inside the machine that is not identified in the instructions, it appea


When you say it is stuck in a wash cycle, do you mean the wash arms are continuously running?\015\012Is there water in the base when you open the door?\015\012\015\012Can you try to run the dishwasher in any other program like rinse ... Dishwashers

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

I have a KitchenAid KDS-17E dishwasher, which has worked well since I acquired it second-hand in 1984. Last night it ran continuously, stuck in the prewash part of fullcycle, with water being pumped through the system, and was fairly warm in the morning. It drained normally when I pressed the Cancel/drain button. I tried the machine again in full cycle. After 20 minutes it was still stuck in prewash, with the water temperature about 42 C, so I stopped it. Machine is connected to cold wate


Your problem is a bad timer.and you really got your moneys worth on this dishwasher.The timers useally go much soon than this one 7-8 years is the norm.The timer gets stuck in one position is a good sign its loseing its ability to fuction normally, ... Dishwashers

Help! My Whirlpool Quiet Partner II isn't working at all. Water was standing in bottom at end of last 2 cycles, but on the last cycle, I came home to clean looking dishes, standing water, and a machine that won't turn on at all- no lights on any buttons- nothing works. I've tried the reset codes published here and elsewhere, but there are no lights on any buttons at all. The circuit breaker is fine. I have 3 young kids and can't function long without my dishwasher!


There is a fuse in the control panel what your model# i can get you the part number its easy to replace it. ... Dishwashers

I have a Diplomat ADP8242 Dishwasher that continues to run during its wash cycle. The machine starts and heats up correctly but will not switch to its rinse cycle and just keeps running with 2 intermitent beeps. I have tried to reset the programe which does pump the water out and resets the control panel, but unfortunatly does not clear the fault. Can you help?


... Dishwashers

My ge dishwasher model gsd6610goobb does not pump any water in to the cycle. Tried to reset but still no water.


... GE 24 in. GSD6260JSS Built-in Dishwasher

Starts cycle, drains ok, then "intake/drain" LED comes on solid for 4 seconds, flashes 4 times, solid 4 seconds, flashes, etc. no water coming into dishwasher. DOUBLE CHECKED the intake filter its all OK ! how do i 'reset' the machine? Im pretty sure the sensor is goofed up and needs to be reset but i have tried holding various buttons, start, power etc, cannot figure out how to do it


... Miele G2430SC Dishwasher

My Bosch Classic Electronic Dishwasher has stopped mid cycle and the "Check Water" light is on. It won't drain at all. The detergent is still in its receptacle. I have tried the reset button on the dial but that doesn't fix it. I have also tried the old, turn it off, turn it back on routine which didn't work either. Please help!!


... Bosch Dishwashers

Hi I have a Neff built in dishwasher s5453X1GB/70 about 4 years old. Never had a problem before. Came downstairs last night to find the kitchen floor flooded. Water also still in machine. But must have been near end of cycle as plates all clean. I have read other links and opened pump compartment in centre of machine and syringed out all water and cleaned fan. When i switch on machine it is still making odd humming noise (emptying cycle?) I have read about anti -flood valve etc. Any more tip


... Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

Our Asko 3530 dishwasher is giving us a 'water inlet fault' code. The machine goes through the pre-drain at cycle start then begins to fill, continues until it's full then kicks out the fault code. I have changed the inlet valve, reset the system to factory default and taken off the lower front panel, finding the overflow area to be dry. Is it time to call for service or is there something else to try before spending the big bucks?


Hi,This sounds like either the overflow sensor or the water control valve is stuck.Usually the valve is a solenoid valve that controls the entrance and fill of the water. If the overflow sensor is underneath, there may be wate ... Asko 24 in. D3530FI Built-in Dishwasher

Won't drain dishwasher goes through all cycles like normal but when it's finished there is still water in bottom, tried to cancel cycle but water stays. I cleaned all the water out and try it again same thing happened. I cleaned the filter so i don't know what else to do!


Make sure the garbage disposal is clear so the water can exit. After that, you may have something caught in the drain hose or check valve. It would require removing the bottom kick plate to gain access to check. ... Kenmore 24 in. 15689 Built-in Dishwasher

My bosh dishwasher SHX55M06UC/46 will not drain. A new disposal was put in and the dishwasher drain plug was not punched out and the dishwasher was ran that way. Now it just holds water in the bottom. I've tried resetting or canceling the wash cycle but that doesn't work and the washing cycle works fine. I'm hoping there is a reset or a safety for the pump if it gets clogged.


... Dishwashers

I tried the steps listed at this website for the same issue I am having. http://www.fixya.com/support/t273954-kenmore_elite_dishwasher The steps worked to get the dishwasher to "reset" with all the lights coming on. The problem I am having now is that after the "reset" the dishwasher starts to run a small cycle for about 5 minutes. Upon opening the washer, nothing has happened inside (no water, no visible movement of parts, no soap container opening). Upon closing the dishwasher and trying


I think think the water fill is ok and the drain is ok as it uses a seperate drain motor . but what is not working is the main wash motor . so no water is moving and the wash arms are not going around and the lights ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Dishwasher flooding Hi my Asko D1716 Super Cleaning System Dishwasher has started to have a flooding problem. When the cycle finished last night it seemed fine then in the morning the machine was full of water, I scooped out the water and by this evening the machine had flooded onto the kitchen floor. I tried other solutions I found on this website but they didn't suit my dishwasher as it doesn't have the appropriate buttons. Any suggestions would be appreciated!


When you say that you tried other solutions.. it's hard to know which you've tried and which you haven't so I will suggest some basics first.. ( if you've tried them, then disregard)...\015\012Have you checked or addressed the following:\ ... Asko D1716 Built-in Dishwasher

My ariston lsv 66 dishwasher will not start washing cycle. It makes the pumping noise as it normally does at the start of the cycle and some water enters the bottom of the machine but then it stops. I have checked to make sure that there are no leaks so the problem is with the filling up of the machine. I live in a hard water area and haven't used anything to help reduce the limescale so expect this to be playing a part. I have tried all the washing cycles but the same thing happens. Any advic


HERE I AM I LIKE THIS JOBE\015\012 PLEASE CHECK THE WATER INLET FILTER I FEEL FROM YOUR DESCRIBE IS IT\015\012 YOU NEED TO CLEAN IT BY ASMALL BRUSH >\015\012 THANKS ... Dishwashers

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

My SHE4402UC/36 dishwasher malfunctioned all the lights were flashing and the machine was trying to drain. The guy came out and replace the control board. The dishwasher now read 199 on all cycles except the rinse and hold, the santitized light does not come when its done. The repair guy told me the count down timers were flakey on the the Bosch dishwashers and it would learn my dishwashing patterns in time. So 6 cycles later the dishes are still damp at the end of the cycle-the length of the cy


Well its not baloney but it is cheesey. normally changing the module is the cure but it has to be programmed correctly. bosch has a recall so check it out and see because the recall is free and the tech is suppose to know how to program it. go to the ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2440 seconds