Having problems with your Dishwashers ?

I have a Maytag Quietseries 300 dishwasher that I bought new in 2004. The buttons on the control panel will not respond. That is, no lights will display when I push the buttons. It has behaved like this in the past and after several weeks of not using it suddenly it will begin working normally again. However, I think this time it has stopped working permanently. The model number is MDBTT79AWW. What do you think could be wrong? I have tried flipping the circuit breaker to reset it but no c


Answers :

Hi
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks for using FixYa. It seems to be the control\015\012board that has gone bad and should be replaced. Prior to replacing the control\015\012board you can take the screws off and then try to blow air with the help of\015\012hair dryer, if still it wont work then you’ll have to replace the control\015\012board. Please do accept the solution if the issue is resolved or post a comment\015\012for further assistance.
\015\012\015\012
\015\012\015\012
\015\012\015\012Thanks
\015\012\015\012Rylee
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Maytag Quietseries 300 dishwasher that I bought new in 2004. The buttons on the control panel will not respond. That is, no lights will display when I push the buttons. It has behaved like this in the past and after several weeks of not using it suddenly it will begin working normally again. However, I think this time it has stopped working permanently. The model number is MDBTT79AWW. What do you think could be wrong? I have tried flipping the circuit breaker to reset it but no c


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. It seems to be the ... Dishwashers

By jleejr on Jul 20, 2010" " I have a Maytag Quietseries 300 dishwasher that I bought new in 2004. The buttons on the control panel will not respond. That is, no lights will display when I push the buttons. It has behaved like this in the past and after several weeks of not using it suddenly it will begin working normally again. However, I think this time it has stopped working permanently. The model number is MDBTT79AWW. What do you think could be wrong? I have tried flipping the circuit breake


HI. The actual culprit in this situation will be your control panel(Defective Touch-pad circuit board). The panel and touch pad assembly are integrated. They share the same space. There is a small ribbon cable on the rear of the control panel that li ... Maytag Dishwashers

After the wash & dry is complete, the next time I try to use it, won't turn on. I tried cancel and that starts and finishes but can't get any thing else to work. I turned off the circuit breaker but have to wait 6-8 hours before turning back on. Once this is done the machines runs normal again. I have to repeat this process every time I want run. Any suggestions on what might be causing this???


I have the same problem. The only temporary solution I have so far is \015\012to turn off the circuit breaker and wait between 10 & 30 minutes \015\012before resetting the breaker. The the dishwasher will work for one \015\012cycle. ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

GE GSD5320 seemed to finish all light wash cycles. Then it began to beep, with the NORMAL light blinking. I hit RESET, but none of the other buttons worked. I threw the circuit breaker for this appliance and waited an hour. I Turned the circuit breaker on but now I get the NORMAL light blinking, even when the door latch is not engaged. No buttons work.


... GE GSD5320DBB Dishwasher

Dishwasher fills with water and then stops. No lights are on at all. I cked wiring and circuit breaker and no issues there. I then flipped off circuit breaker over night. Got up next morning and flipped breaker back on. Dishwasher lights were on and when I pushed Start button, it ran fine. Now it is doing same thing except circuit breaker trick dont work like last time. THERE is NO issues with wiring or connections to dishwasher.


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

Bosch DW model SHU53A05UC/17 was working fine until yesterday evening. Went to turn it on and now get nothing. No lights, no power zip. It's on its own 20amp circuit. Checked the fuse and it's not blown. Flip the breaker on/off a few times anyway to make sure. I was installing a floor and used my miter saw on the sump pump circuit (diff from the DW circuit). It blew the fuse a few times. Any chance, on a diff circuit, it spiked and damaged a board in the DW? What part (part #) would


... Dishwashers

I just bought the Kenmore Ultra Wash Dishwasher model # 665.1389. It worked about 4 times then before the it finished it lost power while it was running. Now it won't turn back on at all. I done everything in the trouble shooting manual and nothing worked. It's not the circuit breaker either. Everything else on the same breaker works fine. What could it be?


... Kenmore PRO 24 in BuiltIn Dishwasher with Ultra Wash HE Filtration 13173

Bosch Dishwasher hi, was thinking of buying a second hand bosch aquasensor dishwasher.. I think the model is Bosch SGS46M78AU.. anyhow thw current owner says it needs 'minor electrical repair to circuit board' and when queried further said that sometimes it washed in normal time and at other times it took up to two hours. Any idea what the prob could be, and would it be costly to fix?? Thanks!


The circut board is very costly stay away from that one ... Dishwashers

When trying to start the dishwasher, pressing the Normal wash button, the dishwasher gives a huge clunk and then it trips the circuit breaker. Upon resetting the breaker, I tried the next button over, which is Soak and Wash, and it seems to go thru the cycle fine. Another time I tried the Normal button, but put the left dial on Rinse and it started up, but it would clunk periodically and it seemed to have a 'hot' smell. I'm worried to use it - what could this be? Is there anything else I can try


Hi\015\012\015\012This is a very dangerous situation you must remove from the wall supply and desist from using, such a fault could easily make the casing "Live" and anyone touching it may be killed. You need to discover why this is happe ... Dishwashers

My kenmore dishwasher, model 665.16473300 has stopped working. Now the lights just flash at the Smart Wash, Normal Wash, and Cancel. I've reset the power and it just comes back. I've taken the drain area apart and made sure there are no obstructions. The buttons seem to respond, as after I reset the unit (breaker), only the Smartwash button is flashing. I push cancel and then it starts flashing. So I think the buttons work, but it's locked up.


IS THE WATER TURNED ON TO THE DISHWASHER ... Dishwashers

Had a Samsung DMT800RHS dishwasher installed by Sears 2 weeks ago. Used it approx. 4 times. Worked well. Today it doesn't turn on. None of the "touch-type" buttons on the console work. Home circuit breaker not tripped. Any ideas?


Hi. We have the same problem. Dishwasher was installed about 3 months ago. There is an easy 'temporary' fix.Completely turn off the dishwasher by flipping the circuit breaker to the off position. Wait a couple of seconds, and flip the ... Samsung Dishwashers

Two days ago my LG dishwasher model lDF 7810BB worked fine. Yesterday I loaded it and the display panel will not light nor show any sign of power. I check the circuit breaker several times and all other electrical items work fine in the kitchen. The 2 year warranty expired 9/08/08


Check for voltage with a multimeter at the wires very near the front, just behind the kick plate. Follow the incoming electrical wire in and remove the little plate the covers the wires/wire nuts. I have seen wires that appear to be connected prope ... LG 24 in. LDF7810 Built-in Dishwasher

I have a Miele model G892SCU Plus Type Hg01. There are no lights on the panel and it will not start. It was working fine last time I used it a couple of days ago. It is hard wired to the circuit breaker panel. (No plug) I checked the breaker. It is on and did not pop.


... Miele G892SC SS Dishwasher

Just had a Bosch dishwasher installed in my new kitchen. The plumber who installed it ran it and it worked. Now we cannot get it to run. We have tried everything. Restarted several times, turned the circuit breaker off and on, changed the cycle and nothing works. The light comes on but it does not get water or run. What are we doing wrong. The dishwasher is brand new out of box but we bought it 4 years ago and remodeling was delayed. Model #SHU5314UC/U06 FD#8001


Test the door switch. It can be faulty or misaligned. You can also check the back of the unit and/or remove the rear panel and take a look at the thermal fuse. It may be bad not allowing enough current flow to operate the machine. ... Bosch SHU5316UC Dishwasher

I was using my Karcher 350M pressure washer working fine but it just stopped having tripped the power boards circuit breaker. The breaker now trips each time I switch on the washer. There is no smell of burnt motor and the electric did not get wet when last in use. Appreciate any suggestions or tests that can be made. I have a decent multimeter. Thanks.


... Karcher 1750 Psi Elec Pressure Washer

Just had a Bosch dishwasher installed in my new kitchen. The plumber who installed it ran it and it worked. Now we cannot get it to run. We have tried everything. Restarted several times, turned the circuit breaker off and on, changed the cycle and nothing works. The light comes on but it does not get water or run. What are we doing wrong. The dishwasher is brand new out of box but we bought it 4 years ago and remodeling was delayed.


Do you have the manual?What is the exact model #?Thanks~! ... Dishwashers

Kenmore Elite Drawer Dishwasher model 465.13329600 Normal Wash and High Temp Wash buttons stay lit, as does green Lock button. The Start/Resume button and the red button on the front of the drawer keep flashing. I've tried key combos suggested above, but nothing seems to work. Even tried shutting it off at the circuit breaker to reset it, and that didn't work either. This ****** was purchased in 2006 or 2007, and hasn't been used very much. WTF?


... Kenmore Dishwashers

Hi In the middle of a wash cycle, my dishwasher tripped the circuit breaker on the wall. I diagnosed this by unpluggin dishwasher, plugging in a different appliance and switching circuit breaker back on. new appliance worked OK. When dishwasher had cooled, I tried it again on same circuit (which I knew was working properly). The lights came on for about three seconds, and then the circuit breaker cut back in again, so I knew it was the dishwasher that was causing the problem. Is there anyt


Ck the connections where the cord hooks to the wiring harness. look for hot or shorted wiring . also ck the contro panel for the same . generaly if you have a power draw like you are saying then you can see t ... Dishwashers

KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher: Just stopped working before Christmas. I had washed a load a day before, and the next day I couldn't use the Rinse Cycle. The lights turn on for Normal and Heavy, but nothing happens when I press Start. I played with the breakers a couple times, to try to "reset" the machine, but it didn't do any good. I really don't want to be spending a lot of money on that dishwasher, especially after reading all the horror stories abo


... KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

Dishwasher has NO POWER! Circuit breaker ok. It worked the last time we used it. No other appliances or lights are out. It appears to be only the dishwasher that has no power. Weird!


Turn breaker off hard to reset it then on2-3 times ... Dishwashers

I have a bosch SHE58C dishwasher. The cycles all work, it fills so the water line is ok, it washes, and it drains so it is not clogged. I cleaned out the sump and it is all clear. However, I think the "brain" or control module is bad. When I try to run a cycle, it does not fill. One other note is that it continues to run when the door is open. Is there a way to reset the "brain"? I've tried killing the circuit breaker


I have a similar problem with my SHE55M15UC model. I bought it last week and I had to push and hold the cancel button before it would start another cycle. If it doesn't finish the previous cycle, it will not let water in. Also, mine doesn't shutoff ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Bosch Dishwasher The label is damaged, but it looks like I have M/N: SHV4303UC Bosch dishwasher. I need to reset (reboot) the electronics. It is stuck in the opening cycle of draining excess water. I've tried turning of the circuit breaker for a long time (10 hours overnight) and that did not work. How can I correct this?


The reason it is doing this is because the anti flood valve is either stuck or you have a leak in the bottom of the dishwasher. if you tip it back slightly does water come out? if so you have a leak, If not take the front panel of and you will see a ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Ignitors keep firing by themselves after my aunt cleaned them 24 hours ago After she did the major cleaning of the stove I used the oven and it worked fine. I lit a burner (Probably front?) and the left rear burner went pop and then all the ignitors keep firing by themselves until I shut off the circuit breaker. Now when ever the stove is turned on the igitors keep firing constantly. I tried unplugging the ignitors one at a time but they all keep firing even if the other ones are disconnected. A


My dishwasher's handle broke off ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

One day the diswasher was working fine...the next time it turned it on it ran for about 3 min. then shut off and seemed to have no power. I checked the breaker...it was fine. A few days went by and all of a sudden the lights were blinking on the panel. So I pushed the cancel drain button. The water drained out and I then proceeded to load the dishwasher and turn it on again thinking it was just a fluke when it shut off earlier in the week. It did the same thing...ran for about 3 min and then shu


... Whirlpool GU2200XTSS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0865 seconds