Having problems with your Dishwashers ?

Smeg dishwasher my smeg dwf409 dishwasher pump keeps on running will not stop after washing cycle and there is water leaking from the bottom of it i can not see any leaks around the pump does the tray on the bottom always have water in it


Answers :

My hotpoint dish washer aquarius is 4 years old leaves a sandy grit all over dishes water not spraying the top,done all the usual stuff run out of ideas
I have a similar problem.

We have and AEG Favorit 675. The pump keeps going even if it is off. I have re-read the manual 5 times and all it says is that the Aqua Lock is activated and to power down the machine. This I have done numerous times.

Any ideas how to de-activate the aqua lock?
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Smeg dishwasher my smeg dwf409 dishwasher pump keeps on running will not stop after washing cycle and there is water leaking from the bottom of it i can not see any leaks around the pump does the tray on the bottom always have water in it


My hotpoint dish washer aquarius is 4 years old leaves a sandy grit all over dishes water not spraying the top,done all the usual stuff run out of ideas ... Dishwashers

I have a GE potscrubber Dishwasher Model # GSD3630ZZ3WW it has been leaking from the bottom for about a week. I took the bottom off tonight and ran the dishwasher so that I could see where it is leaking from. It is not a hose but the leak seems to be coming from the back of the motor or pump fan where it goes into that plastic housing that attaches to the bottom of the dishwasher seems to be leaking in the very center of that housing where the motor shaft enters the housing. Water is just spray


... Dishwashers

I noticed water leaking underneath my dishwasher through the floor joists to my basement. It was a small but steady drip through the joists. I turned off the water to the dishwasher and the leak stopped. I looked inside the dishwasher and there is still some standing water inside the dishwasher, but I cannot see anywhere that water is standing under the dishwasher. I am wondering if the leak is at the pump or at the door? But I see no evidence of the seal leaking.


This is probably the line that goes from the water inlet valve on the bottom of the dishwasher up to the valve leading into the dishwasher itself. It is probably a black corrugated rubber line. This is an extremely bad design, but the solution is s ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

I bought a secondhand Miele 2830 LaPerla dishwasher. I hooked it up today. As soon as I pressed the start button, i heard the pump anf it gave me an F68 error and water leaked out of the bottom in such a way that I could not see where it was coming from. I know f68 means the circulation pump is running when it isn't supposed to. Since I heard the pump, I imagine that is working. So any advice on how to fix this?


The hoses may not be connected properly or are cracked. This is causing leakage inside dishwasher and the flood switch to operate. The dishwasher starts the pump to empty the dishwasher and avoid damage of water flooding the electric parts.Yo ... Dishwashers

I have a leak from the bottom of my GE Nautilus dishwasher. I took the bottom plate of and I can see water coming out around the lever when the drain pump is activated. How could I repair this?


I am having the same problem but i think it has to do with the seal ... GE Nautilus 24" Built-in Dishwasher

Hi, I have a Kenmore 15879 that is basically working except the bottom water spinner...lol (don't know technical name). The dishwasher pumps the water into the bottom of the dishwasher, will heat the water, but not disperse the water in the spinning sprinkler manner it's suposed to. I've opened the dishwasher in time to see that water is spurting out of the holes about 2" high, but it's just not spinning. The water also drains just fine after the whole cycle.


This is caused by the impeller being clogged or the pump is failing, When the pump is woring properly the water will shoot out with force. ... Kenmore 15879 Built-in Dishwasher

Dishwasher leaking Our dishwasher all of a sudden started leaking. I've taken the front panel off the door and can see exactly where. It's not a hole or anything...it's at the front, left edge of the basin, the bottom left corner at the front. It seems that right after it fills with water, it starts to leak once water is moving around inside and washing cycle starts. It is as if big waves are being pushed to the front left corner and over the lip of the basin. I don't think the water level is to


Just an idea...if i'm understanding you correctly,could the door seal be creased there or folded over by use and age to permit this to happen? cause you said nothing is missing ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I have the two drawer dishwasher. It's about 10 years old. The top drawer continues to work OK but for the last three attempts when I run the bottom drawer water gets out into the drip pan below and gives the F1 signal. I can dry the drip pan out and clear the F1 signal so the top drawer works. But running the bottom drawer causes water to leak again with the resultant F1 signal. There is very little water in the bottom drawer (just a little in the filter bowl) so I think the pump is pumping


Hi,Unless you keep using the wrong detergent or keep putting dishes that \015\012are to tall in there. i would have to say your actuators ar bad and its \015\012not letting the lid go down to seal it all the time.There is no adjustment. Y ... Fisher and Paykel Dishwashers

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

Leaks water when operating dishwasher there is some water leaking. If it is the connections under the dishwasher how do you remove the plate/cover at the bottom to see where it is leaking from?


There are 4 screws holding that kick plate on. Normally, they're 1/4" drive. Lay on the floor with a flashlight and look at all 4 corners (between the kick plate and the door and near the floor). This is how to get the panel off, but with ... Westinghouse Dishwashers

I have a Kenmore Model 665.15955792 dishwasher. Water is leaking out the bottom of the door. I changed the door seal and the defusers but it continued. I took off the front of the door and I see the water filling into the base of the machine. When the dishwasher starts the cleam cycle, water is pushed up into the small square holes in the bottom of the door and then splashes up over the lip of the door and out onto the floor. It has never done this before, just started recently. I have had the d


... Kenmore Dishwashers

Maytag jetclean dishwasher leaks: Water leaks underneath. I don't see the source of the leak but see water running out on the left side about midway back on the bottom. Could it be related to the little plug inside the unit on the left side halfway up?


... Dishwashers

I have a Zanussi dishwasher model DA 6141. For some time now it has not been completely discharging the water at the end of a cycle. But sometime it does completely dicharge.Two days ago it started leaking water from its bottom at the end of a cycle.I tried to locate the leak but was unsucessfuly. All the external plumbing is ok andf there is no leak from the discharge pipe nor water intake pipe. So perhaps its something to do with the water pump?


Hello David,\015\012\015\012Have you removed and cleaned both filters and checked they are inserted correctly? I've uploaded the filter cleaning instructions to Flickr for you:\015\012\015\012 ... Zanussi Dishwashers

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

Asko dishwasher- about 1 year old. Dishes are clean but very wet at the end of cycle. The bottom tub is filled with water (looks clean and warm). The dishwasher is leaking and water on tile kitchen floor. I checked for a float device inside and do not see one. What do you think problem is? How can I check hoses to see if clogged- do I need to pull washer out? Is that hard?


... Asko 24 in. 1895 Built-in Dishwasher

Recently our GU1100XTLQ1 started having a problem. It barely cleans the bottom rack, and barely gets top rack wet. The soap stays stuck in the dispenser. I can't see inside as it runs, but my guess is that not enough water is being shot out of the various spinning arms. From looking at diagrams it would appear that this dishwasher uses a pump to circulate water from the bottom of the cavity through the spinning arms. Is my problem a dying pump?


... Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

Our Kemore dishwasher is leaking water onto floor, and the water valve continues to pour water when machine was turned off, but is not leaking water now. There is also standing water at bottom of tub from running machine last night. Can I test to see if it is fill valve or the overfill float? Are these easily replaced?


You just need to clean the pump area in the bottom of your unit :)try to take spray arm out if you can and then open pump cover clean it good but watch for broken glass in it ...and thats it :) ... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

My Asko D1606 doesn't seem to be filling/retaining enough water to pump actively through the swing arms. When I add a litre or so of water in manually and hold in the door catch, I can see it appear to start working properly. The tablet is still sitting on the bottom of the dishwasher after the cycle has ended and the dishes are still dirty. The pump sounds all right and it is emptying fine. Also, probably due to the lack of water, the cutlery basket has melted right through, and I am sure any p


Check to see it the dishwasher has been pushed back ever so slightly. The water coming into dishwashers and exiting are on timers and if the hose is pinched this can affect it. Your dishwasher may appear to be in the same place but just pull it forw ... Dishwashers

My dishwasher will not drain after cycling. I have check the drain hose connected to the disposal. All is in good order the hose is not cinked and the air hole is unblocked. I have also checked the screen at the bottom of the dishwasher, there is no debris or blockage here either. I can run the dishwasher on normal, it cycles but I still have stagnat water left beneath the bottom rack. How do I check my pump to see if it is working or could it be a short of some kind? It is a Kenmore Quite


The problem is a solenoid under the unit. It is a small black cylinder that operates a valve to change from the wash cycle to the drain cycle. You can probably order a new one from Kenmore for pretty cheap. ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

Hello, I have a problem with our Miele G646SC Plus dishwasher. It starts its cycle OK, draining out any residual water, taking in fresh water and doing the initial rinse. After about 5 minutes it then stops with the "inlet/drain" red light flashing. The detergent is still in the holder and the water is still cold. The filter at the bottom of the compartment is clean, the drain pump spins freely. I've also checked for any leaks in the bottom of the machine that would trip the styrofoam/microsw


Hi\015\012\015\012 \015\012\015\012The light flashing means an issue while draining. You would need to check for air\015\012gap on the dishwasher, it may be clogged. It prevents dishwasher\015\012from drain ... Miele 24 in. G646SC Plus Free-Standing Dishwasher

Hello, I have a Frigidaire Dishwasher, model FDB750RCC1. It will not fully drain. There is water in the bottom of the unit after the cycle is complete. As it is not full of water or leaking out of the unit when I open the door I am suspecting it is the pump that has broken? (the water must be draining to the overflow point and then stopping as there is nothing pumping it) Any thoughts or ideas for me anyone? Am I on the right track?


... Frigidaire 24 in. FDB750RCC Stainless Steel Built-in Dishwasher

Leaking Dishwasher My dishwasher is leaking, i looked to see if there was a blockage of some kind but i discoved nothing. I can hear the water pumping in but it seems to leak straight out and is not washing the dishes. Any suggestions would be gratefully recieved. Many thanks.


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101 ... Beko 24 in. D3731F Free-standing Dishwasher

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

My GE Nautilus dishwasher keeps PUMPING water "out" of the machine during the entire wash cycle. I have removed all covers in the bottom of the unit to see if anything is stock. Used vinegar and CLR to remove mineral deposits-- yet nothing solves the water being pumped out the drain hose.. what's next, please.. a solution !?!


If this convert-able dishwasher is permanently installed, you will have to take off the lower access panel to get to the pump area. If it is still in a portable configuration, it may be easier to lay the dishwa ... GE Nautilus 24" Built-in Dishwasher

The sump pump won't stop, even when I turn off the dishwasher. I've dried the water I can see in the drain, but I can't get into the bottom pan to see if there's any water there.


There is water underneath the machine,tripping the flood switch,very common issue with the asko ... Asko D3432XLSS Stainless Steel Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.3055 seconds