Having problems with your Dishwashers ?

Newly installed dishwasher will not fill with water. Runs through cycle with no water. Have checked water supply, it is on, when it runs the normal and heated dry light keep flashing and when I pull the power line it does not reset.


Answers :

Look for a styrofoam spacer under the float switch (the mushroom shaped thing in the bottom.)
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Newly installed dishwasher will not fill with water. Runs through cycle with no water. Have checked water supply, it is on, when it runs the normal and heated dry light keep flashing and when I pull the power line it does not reset.


Look for a styrofoam spacer under the float switch (the mushroom shaped thing in the bottom.) ... Dishwashers

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an


... Asko Dishwashers

My quiet power three keeps running and the sani wash and heated dry lights keep flashing


... GE Dishwashers

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

My Zanussi DE6744 dishwasher won't run it's cycle since I ran a dishwasher cleaner through it. It powers up then stops and flashes 2 green lights alongside a symbol that looks like a bowl with steam rising from it and an arrow with an upright line to it's right. There is also some standing water in the base of the machine. What do these mean.


The first thing I would do is check the float to be sure it is not stuck in the over filled position. Then I would check the drain to be sure that there is nothing clogged in the drain line. Then I would check to make sure the fill valve is working a ... Zanussi 24 in. DE6744 Free-Standing Dishwasher

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

I have a Frigidaire FDB956rbc0 model. When the start/cancel button is pushed nothing happens. There is power and other buttons cause lights above what is pressed come on. Delay wash works but when it starts the washing light flashes. I have run a test on the cycles by pushing start/cancel and power dry button during power failure mode. all cycle run properly. Any thoughts?


... Frigidaire Dishwashers

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

After a power outage, that occured while the dishwasher was running, the lights come on and there is a high pitched noise. Then all the lights go off and the motor sounds like it is starting. However there is no water and the heating elemant comes on. The lights on the front; china/crystal, normal wash, clean and heated dry, all come on as if the computer is confused and trying to run them all simultaneously.


Sounds like the board was fried from a power surge ... GE Tritonr XL GSD6260JCC Dishwasher

Own a Frigidaire Dishwasher Model Number FDB4315LFSO and now after about 2 years suddenly the display will not light and function anything. Without pulling the power panel off the whole line circuit seems to have power as they have my disposal unit tied into same electric line and that runs and so does everything else and no breaker is tripped. Is their a reset somewhere to check or any ideas what can casue the display panel not to function any commands at all. Nick


... Dishwashers

We have ASKO 1805 dish washer. As soon as turn on the power all lights are start flashing and there is no response whatever button is pushed. All the lights simply keep flashing. There is no water being pumped into the machine.


Child lock may be activated ... Asko Dishwashers

Dishwasher does not start it seems there's no water coming in the tub. I got a trouble shooting manual from ejunkie.com and tested the coil of the water valve which read 1000 Ohms, which means it's OK. Then I hot wired the coil while connected to the water line and the valve opened and I had water flowing [ in a bucket] I have tried to start the test program [hold power scrub plus and regular switch at same time then start button] and lights start flashing you hear drain pump come in then the un


... Bosch SHV4803 Dishwasher

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Our Whirlpool KUDP01ILBS2 dishwasher isn't working like it used to. Dishes seem to be getting partially clean, they aren't getting dry at all and it seems they may be being rinsed/washed with dirty water. There is plenty of water in the machine when I interupt the cleaning cycle. I always run the hot water in the sink before I start the dishwasher so the first water into the dishwasher is as hot as possible. Also the sani-rinse light is flashing when the cycle "completes".


Heat that is retained in the dishes is largely responsible for drying\015\012in this dishwasher. Since plastics do not retain heat very well, they\015\012will not dry as well as glasses, ceramics or metal dishes. Rinse aid\015\012must be used so that ... Dishwashers

Hello, We need some assistance with our Kenmore dishwasher. Last night after I started a load, the dishwasher just stopped and then the washing and drying lights started flashing red, sanitized and green are flashing green and the 6 hour delay button is flashing red. I have pushed the start/cancel button but to no avail. My husband shut the power from it to see if it would reboot, it does not help either. It runs a little bit then quits and does not clean the dishes. Could you give us sugg


Hold the start button for 3-4 seconds and see what that does ... Dishwashers

Hi, I have a Miele dishwasher G2150 that after 7-10 minutes on any cycle the rinse, dry, and end lights flash amber. I called the 800 number and they walked me through the diagnostic sequence and they said it was an error code 12 something to do with water restriction. I removed and checked the bottom "L" filter(clean), the wheel (moves freely, not dirty), and the grey in line filter screen on the intake hose,( clean also). I can feel the water coming through the intake hose, water comes in thro


... Miele G2150SC Dishwasher

I have just bought a Kenwood KID60S10 dishwasher. I have used it a couple of times with no problem. However I realised it has been leaking from the water pipe at the back so pulled the unit out to tighten and readjust the pipe. However when I tried to run a cycle it won't after this to check if it was still leaking it won't. When I choose a programme non of the lights light up (except the power on/off light). I had left the washer out of the cavity to ensure the pipe wasn't leaking anymore. It i


... Dishwashers

AFTER A BRIEF POWER OUTAGE DUE TO ELECTRICAL STORM THE F1 CODE FLASHES AND PUMP RUNS CONTINUOUSLY. TURNING POWER OFF ONLY STOPS IT FOR SEVERAL SECONDS. TURNING OFF POWER TO DW AND BACK ON DOES NOT RESET. I HAVE REMOVED THE BOTTOM DRAWER AND CHECKED FOR WATER, BUT UNIT IS DRY. IS THERE ANOTHER WAY TO RESET THE SWITCH?


Hi there,The f1 fault is cased by a leak on the dishwasher.It is activated when water gets to a dangerous level in the base of the appliance near to the PCB.The main reason this happens is putting cups on the drop down s ... Dishwashers

Obtained this haier hdp18pa portable dishwasher, thought I would give it a try. The unit will not fill with water, turn the power on you can hear the motor or the pump running but no water comes in. THe 4 display lights flash and beep a series of times and then stop only to repeat the sound off in a every few second sequence. I have tried the remedies offered online, tilting the unit does not seem to work for me on this one. I changed out the water inlet valve but nothing changed and I got the s


HiYou need to clean the filter that is in the tube that gets water in the dishwasherin case you can not find it pls ask me to send you a diagram ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

My kenmore dishwasher will run part way thru the wash cycle, stop and the hi temp and heat dry lights will flash back and forth and not do anything else. When you open the washer it will have water in it that has not pumper out. It seems that the light wash cycle will work after trying the regular or heavy wash. The washer is 1 1/2 years old. model # 587.15259402


First cut power for ten minutes by unplugging power cord or tripping circuit breaker.If that does not work try the following reset.Press in succession:High temp-air dry-high temp-air dry - High temp-air dry-high te ... Dishwashers

Hi: I have reviewed the forums and tried to fix this issue. Have a Miele G2120 dishwasher that at the end of the cycle - the three (rinsing, drying and end) orange lights begin blinking in harmony. I have removed the triple filter, and two plastic parts to the impeller and made sure all was free of obstruction. I then pulled it out removed the drain hose from in-sinkerator; removed the water line and checked for obstruction. When it gets into this condition - the majority of water drain


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Miele Inspira Series Dishwasher w/ 6 Programs and 5 Temperatures - G2120 / G2120BL - Blac 24 in. Built-in Dishwasher

The "Normal" button light keeps flashing. The door had come open during a wash cycle and there is still water in the bottom of the dishwasher. I've shut off the power, but the light still blinks. Model is KUDSO1FLSS6


The washer had been interrupted during the program cycle and so the main micro controller has hung up. You can remove off plug for few hours or iover night to reset the processor.\015\012Now make sure that the door latch is clicking and contact ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Whirlpool gu2400xtpt3 Green light flashes, doesn't run, how can I repair this myself? "Normal" light keeps blinking; tripping breaker didn't work; all the "sequencing" suggestions (hi temp, heated dry, etc) didn't work. I'm at my wits end. Any ideas? I have a Whirlpool GU258xtpq3


... Whirlpool GU2400XTP Built-in Dishwasher

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2724 seconds