Having problems with your Dishwashers ?

Asko 3100 Dishwasher - when I press the Start/Stop button, all the lights on the cycle program button light up and the dishwasher motor starts up but no water appears in the machine. The dishwasher repair man guesses it is the valve or the computer but is not sure.


Answers :

I am assuming you have the ASKO D3100 dishwasher.
\015\012
\015\012Can you please confirm which lights are flashing - is it one light on top of the program knob or all of them including the one on the Start/ Stop knob.
\015\012
\015\012There are two motors in the machine - one is for the water sprayer pump and the other is for drain water pump.
\015\012
\015\012So it is possible the drain pump motor might be starting because the machine has detected an overfill situation. This can happen even if the machine has no water inside but due to leakage around the door gasket some water may have collected inside the motor / pump cavity.
\015\012
\015\012Yes, the most obvious one as has been diagnosed by the technician is the inlet water valve or the controller is faulty.
\015\012
\015\012let me know which light (s) is flashing (L1, L2 etc) . Hopefully we are both referring to the same user manual.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Asko 3100 Dishwasher - when I press the Start/Stop button, all the lights on the cycle program button light up and the dishwasher motor starts up but no water appears in the machine. The dishwasher repair man guesses it is the valve or the computer but is not sure.


I am assuming you have the ASKO D3100 dishwasher.\015\012\015\012Can you please confirm which lights are flashing - is it one light on top of the program knob or all of them including the one on the Start/ Stop knob.\015\012\ ... Dishwashers

My dishwasher works except is does not appear to be getting water. David psr responded: Most likely the water valve is defective or stopped up with calcium deposits. In either event, you probably need to replace the water fill valve. Not a terribly expensive nor difficult job on most dishwashers. Do I call a plumber, appliance store repair department or look for a local handy man?


I agree that the fill valve may be bad or clogged. You can fairly easily remove the valve yourself if you are somewhat handy and then take it apart and clean it. I doubt if the old valve is electrically shot but it is possible. Cleaning it out may ... GE Dishwashers

Hello everybody, I hope that you gona a give me some tips for repairing my dishwasher mashine. A few days ago, the error F2 appears on my dishwasher machine (Baucknecht GSI 5894) I checked the pump for the waste water is ok. the tap water is not taking in,I checked the hoses they are ok as well I turned off and on and same time pressed the button reset and choosing the programm on the dishwasher few seconds trying to start and again apperas F2 . Hopefully someone can help me. Best regard


Possible the inlet valve has given up and is not allowing water in.\012Also possible there is a slight leak enough to shut the water off (safety feature) - Check underneath for a float mechanism and any water there. ... Bauknecht Dishwashers

I turned on my Whirlpool dishwasher last night before I went to bed. It is a model number DU915PwP82. Sometime shortly after that, a water line broke in my neighborhood. The water was off and caused some sort of problem with my dishwasher. There is some water in the bottom of the dishwasher. It won't drain or start washing. Do I need to call a repair man or is there a reset button of some sort. Thanks for your help. Rina


Hi.\015\012Often there is a lot of grit in the water supply after a pipe has been repaired, and this may have clogged one or more of the valves in your line, or the gauze filter in the inlet port on your machine. I would first turn off the wate ... Whirlpool Dishwashers

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David


Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher

Whirlpool Quiet Wash Plus dishwasher Model DU920PFGZ3. Worked fine until I replaced the insinkerator and forgot to punch the drain plug leaving water standing on the bottom of the machine. I punched the drain opening, and pushed the cancel/drain cycle button. It drained fine but since no water comes from the spray arms. I have removed the arm all the way down..NOTHING!! Some research indicated it could be the water inlet valve. When the buttons are pushed, it cycles but no spray or water.


... Dishwashers

My dishwasher AEG favorit 525 worked perfectly but has been out of action for over a year. yesterday when I tried to use it, the on button is on continuously and no water is pumped into the machine. yes the water is on. the program button is also rotating as the programs change but no water comes in and I am not sure whether it will pump water out as I have not yet got there. please help.


Hi\015\012\015\012The issue seems to with the pressure switch that is bad and\015\012so won't allow the water to flow inside the unit. You can take it apart to\015\012check this. Hope this helps...please post back for further assistance. ... Dishwashers

Dishwasher repair My bosch dishwasher shu5305uc/u11 does not fill with water but the water valve appears to work.


Make certain that there is water coming into the d/w if so and you are sure that the solenoid on the water valve energizes then its possible that the strainer on the water valve might be clogged if so its going to take a bit of work to remove and cle ... Bosch 24 in. SHU5305UC Built-in Dishwasher

Our dishwasher beeps twice when the start button is pressed but then doesn't do anything and there is no other noise from anywhere (eg, motor/pump). There are no error codes displayed and the display appears normal (ie lights up and shows time for program completion etc). When the problem first occurred the machine was full of dirty water. We have turned the dishwasher off and on at the wall, checked/cleaned all filters, drained the dirty water and still nothing happens (it doesn't even fill


... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

My dishwasher (kleenmaid brandt super silent DW121TB) appears stuck in a wash cycle; how do I reset the program? I have read the instruction book to no available, tried unplugging power overnight, tried a combination of simultaneously holding buttons in and switching on, letting the machine run all night, drained the water and added clean unsudded water, and none have corrected the situation. There is also a selection lever inside the machine that is not identified in the instructions, it appea


When you say it is stuck in a wash cycle, do you mean the wash arms are continuously running?\015\012Is there water in the base when you open the door?\015\012\015\012Can you try to run the dishwasher in any other program like rinse ... Dishwashers

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My dishwasher is not washing. It runs water in and out, but is not washing. I hear the motor. The repair man told me that I would need top get to the chopper inside the dishwasher. I am not sure how to do this. Is there an illustration of this somewhere?


Appliance repair parts stores carry service manuals for individual brands if you need step by step instructions. The basic procedure is to disassemble the lower spray arm assembly down to the deck. If you attempt this, keep track of the placement of ... Whirlpool DU1055XTS Built-in Dishwasher

My dishwasher will start any program, it drains, fills, empties & beeps continually within a few minutes. The rinse light stays on until the machine is turned off & re-set. Aditonally, the ater heating has been hit & miss for some time! A service guy cleaned the water sensor with hot water fro a ketle + tooth brush, but the problem came back after a couple of weeks. Having removed item he cleaned, it looks fine and appears to switch OK. Not sure if its actually faulty. Is the themperature sensor


... Whirlpool 24 in. ADG7540 Built-in Dishwasher

I have a bosch SHV43A03GB dishwasher. It has a problem when it cut out water flow in. the guy who repairs it seem s only to have to push a button or switch under the machine to get it to work again, cant find switch/ button- please help!


Programmer not working ... Bosch 24 in. SHU53 Built-in Dishwasher

Dishwasher Repair Dishwasher is a Stoves/Newhome DW616 Rotating spray arms do not always operate. This is an intermittent problem - will sometimes work normally for a few days then arms will not move at all with no water coming from them. Machine appears to go through its normal cycle. Some times cycle starts normaly and spray arms stop working part way through.


It could be a motor or a pump issue. The dishwasher has a motor that attached to a pump which forces the water up into the sprayer arms and during the drain cycle, it pushes the water out of the dishwasher. \015\012The motor (and pump) located beneat ... Dishwashers

My AEG Favorit Sensorlogic Turbodry dishwasher is making 3 short continuous beeps which I understand means the leak prevention system has kicked in. Is there something I can do to reset or must I call a repair man/ There is no water in the machine it has all drained.The machine no is actually a F86050VI


Open the left metal panel, if the white plastic tank is black at the bottom or is not clean: remove it, open it, clean it (make sure the water flows through properly) and put it back in. ... AEG 24 in. Favorit 80860iW Built-in Dishwasher

Zanussi DW908 dishwasher will not fill with water, when filled manually completes cycle untill fill time again. when filled continues on until water needed again. Only cold supply to machine. Water coming to valve, removed valve and freed it up as it was stuck, water flows through the valve when disconected from the dishwasher at filler pipe which leads up the side of washing chamber. When all connected up water will not enter the dishwasher. I,m beaten as I cannot access this area without maj


\012\012Hi,\012Here\012is a tip that will help you to find out why water will not come into\012the dishwasher... Dishwasher Trouble ... Zanussi Dishwashers

My Bosch dishwasher is Exxcel 5 prg model no SMS50E020GB. When you first open the dishwasher door after the washing cycle finishes there is no water in the bottom of the dishwasher but about 45 minutes later water slowly appears in the bottom of the dishwasher. I scoup out the water and there is about 3 litres. The machine is just over 2 years old. I had a plumber check the machine and he couldn't find anything wrong with the machine. Another plumber came out and put on the invoice: "disma


... Bosch Dishwashers

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

My mother has cancer so needs me to research her problem with her dishwasher. My mother's sink drain water is emptying into the dishwasher. It has to be manually removed since she does not cook much and therefore no longer uses the dishwasher as much as she used to. Is there anything I can do without calling a repair man or plumber? And if I must call a repair man, which should I call, a Maytag repair man or a plumber?


Problems associated with water from the kitchen sink back filling into the dishwasher are caused by the drain line on the dishwasher not having a high end loop. In simple terms, the dishwasher line is too low and is providing a path for the water to ... Maytag Dishwashers

I have a Kenmore 363.15655891 Dishwasher. It will not fill with water. I have replaced the fill valve, water is on to the machine. When I check the electric connection for the fill valve it does no


... Dishwashers

Cookworks wqp8-9239 slimline dishwasher. Start the cycle on setting 1-4 and half to three quarters of the way through it stops and starts beeping with the first 3 buttons of the control panel flashing. The manual says when lights begin to glimmer the machine is out of order? can i ficks this without sending for repair man?


... Dishwashers

Starts cycle, drains ok, then "intake/drain" LED comes on solid for 4 seconds, flashes 4 times, solid 4 seconds, flashes, etc. no water coming into dishwasher. DOUBLE CHECKED the intake filter its all OK ! how do i 'reset' the machine? Im pretty sure the sensor is goofed up and needs to be reset but i have tried holding various buttons, start, power etc, cannot figure out how to do it


... Miele G2430SC Dishwasher

Dishwasher is full of water at end of the wash cycle. It drains when I push the cancel/drain button though. I dismanteled the drain hose from the pump and blew through the check valve to the drain. It is clear. This machine has a sensor after the drain pump. What does it do? Thanks Carl


The drain pump needs to be replace. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2816 seconds