Having problems with your Dishwashers ?

My Bosch dishwasher stops with one minute left on the timer but keeps running most time the soap dispencer door has not opened


Answers :

Ok The soap dispenser is controlled by a wax plunger. This is mounted in the door on the back of the dispenser. Remove the door panel and gain access to the wax motor. Two wires connected to a brown colored small rectangular box about 1 inch long.You must check this wax plunger for resistance and short circuits. This item is a naughty little thing and can blow up your electronic. for mine I would get a new wax plunger and fit it straight away.They dont cost that much. After this if the fault still counts down to 1 tell me if the motor is still running at the end of the cycle. It very well might be. If this is so the electronic may be faulty. You can menil me on [email protected] for further assistance.
\015\012Also check to see if the cycle works normally on the rinse . That is a cycle whit no heat. Just the pre rinse.
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bosch dishwasher stops with one minute left on the timer but keeps running most time the soap dispencer door has not opened


Ok The soap dispenser is controlled by a wax plunger. This is mounted in the door on the back of the dispenser. Remove the door panel and gain access to the wax motor. Two wires connected to a brown colored small rectangular box about 1 inch long.You ... Dishwashers

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

After the cycle runs i open the door and all the soap appears to have just dumped out and is on the inside of the door. I have tried liquid and solid tablets of detergent and neither it working. It seems the soap door isn't opening at the correct time. The washer has only been used for a year! Any ideas of an easy fix? Thanks


Sound like you have to change your dispenser.chek out sear parts direct.com for parts,image,prices and part #s let me know if i was helpful. ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

My soap cap remains in the closed position at all times. The clasp mechanism works fine, if I cycle through with the door open I can see and hear the catch release when it should. But the door remains closed at all times. I leave it open to run, and sometimes it's closed when the wash cycle finishes! Is there an easy way to take the cap off and clean it? Or do I need to WD-40 around it?


There is a little spring in there that flips the door open, just take the screws off of the side of the door, you'll see the broken spring by the door, make sure power is off to dishwasher ... GE Nautilus 24" Built-in Dishwasher

The machine is running well Hotpoint BFV62 but the soap dish is now failing to open. Is there a sensor that triggers the door to open or is it a timed open sequence within the program. Suggestions on part replacements or remedial action would be appreciated.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

Dishes have lots of residue on them. I have to scrub them with a scouring pad to get it off. I have done the citric acid thing and that did nothing. I have run the dishwasher without any soap in to "rinse" it out and when I open the door mid cycle there is lots! of soap in the water. I have done this about 30 times and there is still lots of soap


Hi,It seems like the dishwasher is not draining properly....Sometimes it will drain at the end of the cycle but not during the cycle....that is a circuit board issue....if it does not drain at all then you have other issues,,,, ... Maytag 24 in. MDB4100 Built-in Dishwasher

Dishwasher malfunction MOST OF THE TIME it shuts itself down before fully filling with water - SOMETIMES it doesn't shut down until the minute the wash pump starts - SOMETIMES it washes for 10 or 20 minutes before shutting down - SOMETIMES it will even run a whole cycle, BUT it doesn't open the soap dispenser door - tried doing a diagnostic run but after it turned on all the lights on the panel it started to fill with water and shut itself down......... HELP


Follow this steps and fix it. God bless youFloat Switch\012\012\012The float switch may be hung up and this can cause the dishwasher to be stuck in a cycle. Check the ... Dishwashers

Soap dispencer door dosnt seem to be opening at the right time. i find the soap undisolved in the bottom of washer, and dishes are not clean.


\012Hi,\012\012There\012are three common problems that cause the Soap Dispenser or Cup not to\012open. I have a tip that will explain these problems in\012detail....Dishwasher Repair Problem ... GE Nautilus 24" Built-in Dishwasher

My dishwasher clean light keeps flashing ... turned the braker off, open and closed the door several times, as well as the soap holder, moved the latch where the door closes ... not sure what else to do ... what else can I try?


The reset sequence used was reported to be the following:1) Crack the door open.2) Within 3 seconds press the following sequence - Hi Temp Scrub, Energy Saver Dry, Hi Temp Scrub, Energy Saver Dry3) Close and latch the door4) P ... Whirlpool GU2400XTP Built-in Dishwasher

GE Nautilus My dishwasher is approx. 6 years old. It has recently started having this problem. On the second cycle (the one where the little door inside opens and release the soap) does not want to work right. The door will open, but it is like there is no water spraying to spread it out. The soap (I've tried both liquid and powder) sticks and drys, running down the door and in the bottom of the tray. I have to open the machine and add the soap to the bottom of the machine if I want to get my di


Smoking from GE (Model:gsd3725f00bb) dishwasherWe moved in an old house, the dishwasher had been installed. but today we found smoking from the dishwasher and smells burned plastic. Could you have any resolution for me? or this problem is popul ... GE Nautilus 24" Built-in Dishwasher

Soap dipenser My whirlpool built-in dishwasher model DU930PWPB0 serial # FR4104078. The door to the soap dispenser will not open. I have been washing the dishes with the door open all the time. When I close it(door) it won't pop open when it should. to dispense the soap in the wash cycle.


Try this... Wipe out the soap dish with white vinegar and a soft cloth.. make sure you get everything off the edges of the door and look for any nicks, blemishes or deformation of the dispenser door to make sure it is not mechanically binding up when ... Whirlpool 24 in. DU930PWP Built-in Dishwasher

Frigidaire model F71C12PHS0 is not washing, it goes through the cycle and when the door is opened the soap container is open with soap still in it. We have run it with the door open to see if it is spraying and it is. The heat is working because when we open it at the end of cycle it is hot. Yet soap is still there and dishes are not clean. Thanks to anyone who can help me trouble shoot this.


... Frigidaire 18 in. FDR252RB Built-in Dishwasher

After running a cycle, there is some water in the tub and the soap dispenser is open but the soap has only run down the inside of the door. It does not sound like there is a vigorous spray during the wash cycle. Opening the door during the wash cycle reveals only a little water reaching the upper arm.


May have a stripped wash impeller. I would tear into the pump and look for any kind of obstruction but if its clean probably the motor assembly needs replacing. ... Frigidaire Dishwashers

The dishwasher sat for 4 weeks in our basement while we remodeled our kitchen. When we ran it for the first time, the soap is just driping down the door..either it isn't opening at the right time, or the water isn't spraying where the soap is opening on the door. HELP


Two things will cause this problem ,1low water pressure to the machine.2blocked pipes check all filters and run the hotest tempture wash on the machine also put two tablets in the hot wash it should be ok.adrian;;;;; ... Kenmore 24 in. 15079 Built-in Dishwasher

Whirlpool DU927QWDG1 Hi, The problem I'm having with my dishwasher pertains to the door cover for the area I place the soap. There is a small spring which helps the door pop open to release the soap when washing. I cant figure out how to place the spring so that the pops open.....right now when I run the unit the door stays latched and the soap doesn't get dispensed. Any ideas on how to repair this or where I could maybe get a parts manual??? Your expertise will be greatly appreciated!!!!


... Whirlpool GU2400XTP Built-in Dishwasher

Have the Kenmore Limited Edition dishwasher, model # 665.15892100. When dishwasher is running, you can hear the soap container flip open. However, @ end of washer's completion, and main door is opened, the soap is still in the container. Some has leaked out, but the majority is still in the container. Dishes are still dirty, so it appears that either there is no water to disperse the soap, or does the door really open? Any ideas?


Check the wash arms to see if food has not cloged the holes stopping water getting through\015\012if these are clean the machine may not have enough water entering machine\015\012also check how you stack machine ... Dishwashers

Kitchenaid model kudso3ctblo, Type 577-0 Ser. FU3202943 When the dishwasher is finished, the soap tablet is still inside the dispenser & the door is still closed. We can open the door by hand & see that the soap has not dissolved. We found a tiny spring on the floor last week. Is there a metal spring in the dispenser? Could this have broken off & now keeps the door from opening?


... Dishwashers

I have a whirlpool DU1055XTSQ3 dishwasher. When the dishwasher has run through it's cycle and says it finished, I open the door and the soap door is open with the soap packet still there. What causes this and how do I fix it? Thank you, mary


... Dishwashers

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Asko dw20 pump keeps running even with door open and turned off... The machine got to the final cycle then the pump just keeps running and the glass icon (L2) keeps flashing. All the water is not evacuated from the washer. When I power off from the front the drain pump still runs (and water is still not draining). When I power cycle from the mains (waiting 10 seconds) the pump engages again and the water level drops a bit and then stops draining. I have done this until all the water is empty an


... Asko Dishwashers

I have an Asko 3251 that is about 4 years old. It has been great up until 2 nights ago when it just keeps running when is has completely cycled. You can open the door and it keeps running. You can push the shut off button and the lights on the controls go out but something keeps running. The only way I can shut it off is by shutting off the circuit breaker. The next morning I can turn the breaker back on and it will be off. Does anyone have an idea what is causing this?


... Asko 24 in. D3250 Built-in Dishwasher

Dishes and the dishwasher look dirty after they run, like it redistributed dirty water. The door is very dirty/filmy except right under the soap dispenser, like someone squirted dirty water on it but wiped right under the soap dispenser. If I run it a second time with vinegar it gets clean, but that is crazy, esp since it takes 2 1/2 hours a load. I have 2 of them and both are doing it. I have changed soaps, added more soap, used less soap, pre-rinsed dishes, put them in filthy, used jet-dry, no


Hi Mike_wend604,\015\012\015\012I am looking for a used Asko #1504, if you would like to sell yours please e-mail me at [email protected] and put "Asko" in the ... Dishwashers

After running, I open up DW and find all the soap lying in the bottom of the dishwasher by the round thing directly below the soap cup. Is the door opening up early and letting all the soap out? Am I maybe filling the soap cup with too much detergent?


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Dishwashers

Bosch SHE55P05UC Used it maybe 10 times in 10 months (long remodel underway) and noticed it didn't work properly. Powers up, but doesn't always fill with water...just "runs" until I shut it off. Or it fills, runs most of cycle, but the soap doesn't open, and I end up with a hard soap "cake" at end of cycle...Or it washes..with soap, but during drying...never turns off...and I'm not sure when the problem occurs, but that everything is wet. At least with this one....I can do


... Bosch Evolution 500 SHE55P05UC Full Console Dishwasher - Stainless Steel

GE profile model GSD 4120y70BB the second soap dispensor does not open at the right time. When cycle is done and the door is opened the soap has just ran down. It is like it is opening to late.


Hi\015\012 \015\012Many dishwashers (but not all) use a BI-metal strip that heats up once power is applied to it. The BI-metal strip bends and allows the soap door spring to open up the dispenser. This b ... GE Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1589 seconds