Having problems with your Dishwashers ?

I have a Kenmore Ultrawash dishwasher #13743 with blinking sani-rinse lights. I tried resetting the breaker to no avail.


Answers :

HI. There are two possible culprits here. The areas of concern will be the element and the control panel interface. In order to isolate the issue, you will need to test the element for proper continuity. Please post the entire model number, if possible. This information is needed to post the correct diagrams and part numbers needed at this time. The model number you have posted above is incomplete and unusable. Please post the entire model number associated with this unit, asap.

Thanks..
Hi
\015\012
\015\012
\015\012Thanks for using FixYa.
To\015\012resolve this issue you will have to reset the console. Do this by closing the\015\012door and press these buttons in sequence...
\015\012\015\012
\015\012-high temp wash/Saini rinse

\015\012\015\012-heated\015\012dry/air dry
\015\012\015\012-high\015\012temp wash/Saini rinse
\015\012\015\012-heated\015\012dry/air dry
\015\012\015\012
\015\012\015\012
\015\012\015\012Please do accept the solution if the issue is\015\012resolved or post a comment for further assistance.
\015\012
\015\012
\015\012Thanks
\015\012Rylee
\015\012

Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Kenmore Ultrawash dishwasher #13743 with blinking sani-rinse lights. I tried resetting the breaker to no avail.


HI. There are two possible culprits here. The areas of concern will be the element and the control panel interface. In order to isolate the issue, you will need to test the element for proper continuity. Please post the entire model number, if possib ... Dishwashers

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

Kenmore dishwasher 665.13843K601 ser. FU4806977 STOCK 13843K TYPE 575-0 Tried to turn it on won't start/ run/ perform any functions The following buttons light up but will not perform functions; Smart wash and heated dry also lights up like it should, pots and pans, normal, fast wash, high temp, sani rinse The following buttons do not perform functions or light up Quick rinse, Turbo ZOne, Delay Hrs., Cancel/Drain, Start/Resume I killed the power to it for 1 minute for reset but d


The touch pad is not working. Pull the front kick plate from font/bottom of machine and there is a 'TECH SHEET'. This has a complete diagnostic sequence for you to go through and verify the functions for you. ... Dishwashers

Kenmore 665.15822 My quick rinse light (red) blinks and dishwasher will not start. Have tried turning breaker off for a while, doing the Sani Rinse/Air Dry button pushing...with no luck..HELP!


Hi,Sorry you are having trouble, the symptom of the quick rinse light blinking means there was a failure in the keypad. The most likely reason for the failure is when moisture gets under the keys (buttons) and a bit of corrosion takes ove ... Dishwashers

Dishwasher inoperative The lights that indicate the wash cycle are flashing along with the 6 hour delay light. I have tried to cancel the cycle but it does not work. I shut off the breaker to try and reset the operation and that does not work. The dishwasher will not work and I cannot reset or cancel the flashing operations. Kenmore Quite Guard 3 Model 587 15072200


... Kenmore 15522 Built-in Dishwasher

Kenmore elite dishwasher model #665.13942k010 is 1 yr old and stuck in rinse mode..tried combo button pushing....no lights or beeps....tried the breaker in off position....blue light keeps flashing rinseing with 3 bars.....appreciate the help Thanks Steve


... Kenmore Dishwashers

Kenmore Elite 665.15929001 Dishwasher, flashing Sani-Rinse light, won't start


Kenmore is **** with a double PP go buy a Maytag or GE and throw it threw the appliance dept like the Discount tire guy did on TV. I have asked the same question on 4 different blog's and no answer. The question to where they were actually built is u ... Dishwashers

My Kenmore 15652 dishwasher has the Pots/Pans light blinking. When I try to press cancel the quick rinse light also blinks, as well as the cancel light and the pots/pans light. When I release cancel the pots/pans light still blinks and the other two turn off. How do I reset dishwasher so it works normal?


... Kenmore 24 in. 15652 Built-in Dishwasher

I have a kenmore dishwasher model #655.1374 or 655.1384 which is only about a year old. I am having a problem with the controls. It will not allow me to use smartwash. The only control that can be used is quick rinse. I reset it by pushing Sani rinse and heated dry. All the lights come on and it seems to do a test. But after that still the same thing except if I push start resume it goes to normal wash which stays on a long time and periodically the cancel drain light comes on as well as the 4


... Dishwashers

Here again is my model and serial it stops in the middle of the cleaning cycle Kenmore 665.16773402 serial # ft0302854 Here is how I have been resetting the dishwasher. I hit the following sequence of buttons: Normal Wash Heated Dry Normal Wash Heated Dry Normal Wash After that ? all the lights are lit up as follows: Smart Wash, Pots Pans, Normal Wash, China Gentle, Turbo Zone, Hi Temp Wash, Sani Rinse, Heated Dry, Sanitized (Green light ? not a button), Lock on (Red Light ? no


Door latch.Open and close the door to make sure the door latch is securely fastened\015\012 \015\012Hi-Temp Wash, Hi-Temp Rinse, or Sanitize options.Some models have options that may requi ... Dishwashers

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher: Just stopped working before Christmas. I had washed a load a day before, and the next day I couldn't use the Rinse Cycle. The lights turn on for Normal and Heavy, but nothing happens when I press Start. I played with the breakers a couple times, to try to "reset" the machine, but it didn't do any good. I really don't want to be spending a lot of money on that dishwasher, especially after reading all the horror stories abo


... KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher

My Whirlpool GU1500XTKQ0 dishwasher "rinse only" light is flashing, the buttons on the control panel do not work, and of course neither does the dishwasher. I have tried resetting the circuit breaker - no luck.


... Dishwashers

Have a Maytag dishwasher that will not run, display panel just has three blinking lights. Have turned off circuit breaker trying to reset dishwasher, to no avail. Still blinking.


Behind the lights and the control buttons there is a central control circuit board (known as the CCU), this board is going to need to be replaced, the part price depends on the model number of the dish washer, but on a ... Maytag Dishwashers

I have a Kenmore dishwasher model 665 15829000 just shut off wont come back on . The lights started flashing when I tried to reset it.Is there a reset button on this model and if so where is it located? I did check the breaker ,to make sure it was"nt that.


... Kenmore Dishwashers

Frigidaire Dishwasher model # FDB520RHB2 Stopped prematurely last night while on light cycle, now will not respond at all. Noticed water at bottom of tub; tried draining manually through drain tube, removed lower arm, glass trap, and filter, and water remains; tried electronic reset by switching off breaker for several minutes; all to no avail. Electronic controls (cycle/option select) will not respond at all.


This is not a uncommon problem and it sometime's is the pc control panel but i find that it is more often the interlock ( latch assembly .) i would change // there has been a improvment and i belive this will solv ... Dishwashers

Kenmore dishwasher My dishwasher stopped in the rinse cycle and no longer appears to be getting power, although the breaker works and the plug it is connected to is still receiving power. Is there a reset button for the motor, or some other idea to try and fix this? Thank you for your assistance. Mark


Mark, you probabley blew the thermal fuse located on the main board. Easy fix. Part number 8269213. You can ohm it out to be sure. You have to remove the inner panel to get at the control board. The fuse sits on the top side and clips on. Two wires ... Kenmore 24 in. 16293 Built-in Dishwasher

Kenmore 74362 My model# is 665.74362400 this unit is only just over one year old. My problem is it shut down and the quick rinse light started blinking. I have tried some of the button-reset procedures that were on some other responses but to no avell I even left it unplugged for a while. Any impute would be appreciated. I have a Kenmore Dishwasher Model #74362. After we run a cycle for a normal wash and heated dry the dishes are all very dirty and greasy. It is as if they were never washed. Th


I had the same issue and you will never beleive the solution.\015\012Steps to follow:\015\0121) run one full cycle with no dishes or soap\015\0122) run one full cycle with a dishwasher cleaner like Jetdry\015\0123) run one ful ... Dishwashers

My Kenmore Dishwasher won't turn on. Was working fine last week, but when I went to start it yesterday, nothing starts or lights up when I push the button. The options buttons still light up, but thats it, the wash cycles and the start and stop buttons...nothing happens. I tried tripping the breaker to reset and it did no good.


Hi,\015\012\015\012A device may cease to function or operate sporadically if the electrical cord is damaged. Inspect the cord for any damage. Check whether there are any black smudges or burn marks on the outlet, cord or anywhere the cord comes ... Kenmore 15129 Built-in Dishwasher

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

I have a whirlpool du1055xtsq3 dishwasher that is partially working. Cycle buttons light up but start button does not. I've tried resetting by pushing sani-rinse and heated dry alternately. Control panel lit up and heard motor running but no water. Your help is appreciated. Unit only 2yrs old. Thanks!


... Whirlpool Dishwashers

I have a Whirlpool ADG937 dishwasher (9 years old) which will not complete a 65c wash cycle. It starts Ok and runs for a long time but then continually bleeps, when I open the door the programme indicator light is on the rinse cycle. If I reset the programme to 65c it may do the same or occasionally it will finish the cycle. I have tried salt top-up, descaling and filter cleaning all to no avail. Is the programmer faulty (can I bypass it?)or should I replace the washer?


... Whirlpool Dishwashers

Hello, My Kenmore elite dishwasher model 665.17282.400 seems to have a problem. The CLEAN light is flashing and can't do anything else with it. Do you know what thew problem is, or how to reset it. I tried cotting off the power to the unit but to no avail. Please help ASAP


Try pressing the heated wash then heated dry one after the other about 5 times. this should reset the unit.\015\012\015\012\015\012--------\015\012in some machines there is "Hi temp scrub " and "air dry" so press this ... Kenmore 24 in. 17282 Built-in Dishwasher

I have a Kenmore undercounter dishwasher..model 665.16022400. The "normal wash" light keeps blinking..nothing will work on it..I tried reseting didn't work, killed the breaker for a while, didn't work. I tool the panel off and reseated the ribbon connection to the electronic board..didn't work. I'm not sure if I should be replacing the electronic board, or the control panel that contains the buttons. None of the buttons appear to be stuck. thanks - Andrew


Hi,This is a common problem. As i cannot diagnose the machine myself, it would be tough to exactly comment on the fault. However, more often it is an issue with control panel keypad assembly.You need to replace that.Let me kno ... Kenmore 16024 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2807 seconds