Having problems with your Dishwashers ?

I have to replace the handle / latch assembly on a GE Monogram Dishwasher Model #ZBD6600G03SS. For the love of me I can't see how to do it. Do I have to get at it from inside, outside, both sides simultaneously?


Answers :

Hi
\015\012
\015\012If the dishwasher door will not latch on your GE Monogram dishwasher and it is a new appliance, check that the door is not hitting screws or cabinets underneath the counter. For a new dishwasher, you might also need to push in the top of the control panel as you latch the door. The new gaskets might not have had time to seat properly. It may be necessary to run up to 10 dishwasher cycles for the heat from the washer to seat the gasket, which becomes more flexible after it is used a few times. For older Monogram dishwashers, check the loading rack to be sure no dishes are protruding beyond the back or front of the racks and that no dishes have fallen through to the lower rack. If dishes are dangling down into the lower rack, they could stop the lower rack from completely rolling into the dishwasher and could also stop the spray arm from rotating. Check that no silverware is obstructing the door.

http://www.acmehowto.com/howto/appliance/dishwasher/check/doorlatch.php
\015\012
\015\012
\015\012Let us know if you have something more to know else accept the suggestion.
\015\012Thank You for contacting Fixya.com
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have to replace the handle / latch assembly on a GE Monogram Dishwasher Model #ZBD6600G03SS. For the love of me I can't see how to do it. Do I have to get at it from inside, outside, both sides simultaneously?


Hi\015\012\015\012If the dishwasher door will not latch on your GE Monogram dishwasher and it is a new appliance, check that the door is not hitting screws or cabinets underneath the counter. For a new dishwasher, you might also need to p ... Dishwashers

Kenmore 17362 dishwasher was making a bad noise and now the motor seems to be locked up. I might have already un-jammed the motor by removing the cover on the bottom (inside), and turning the knife impeller on the outside of the screen, but I can see lint type material in the hole on the other side of the impeller. Hard to explain, but it is in the hole in the center of the unit and there is a screen like the knife impeller has behind it. I could clean this lint if I could get the door off. How


... Kenmore 24 in. 17362 / 17364 / 17369 Built-in Dishwasher

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

HI dishwasher will not drain if i remove all the water will run thro cycle and stops with a couple of cms of water left have tryed to find filter inside and failed, removed sides and can see a pump on right hand side can turn impeller easily, is this the drain pump? if not how do i get at pump and or filter. is it possible that plastic chamber on left hand side could be blocked assume this transfers heat Robert


... Bosch 18 in. SRS55L02 Logixx Slim-Line Free-standing Dishwasher

Within the last month our GU1200 is noisy and not getting the dishes clean....I did pull out some melted clogged debrise from the "dish module". WOndering if something else is still in side? and how do I dismantle the lower spray arm to get inside and see?


THERE SHOULD BE SOMETHING HOLDING IT DOWN, JUST BE SURE THAT YOU REMEMBER THE SEQUENCE OF PARTS. THE MELTED PARTS ARE FROM THE DRY CYCLE WITH PLASTIC LAYING ON THE ELEMENT. SOMETIMES THERE IS A PLASTIC THREADED PIECE OTHER TIMES IT IS A METAL SCREW ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

My SGS55M72AU/65 does not get rid of its drain water, although that wee pump in the bottom is clearly working (which I could see after removing filters and pump cover). There is no blockage near the drain pipe connection, so I infer there is a blockage somewhere inside the dishwasher, in a place I can't get to without further instruction. I've removed most of the drain water and pulled the unit out, so I could lay it on its side and start taking screws out. But I much prefer to have some guidanc


Ok i am attempting to help you although i dont see your make of dishwasher but im using what i know without manual. to ensure there is a blockage in the dishwasher remove that hose you checked at garbage disposal or vent and leave it disconnected an ... Dishwashers

Disconnected dishwasher and moved out in order to tile the kitchen floor. Ten days later reconnected dishwasher. Turned on water supply to leak check -- no water is getting into the washer. - Ran hot water from sink side to see if that would help, no such luck - Disconnected water line and water is in the line up to the connection point at dishwasher. Looked inside valve of dishwasher for obstruction - no such luck - Disconnected both ends of water line and blew in line to check for obst


... Bosch Evolution 500 SHE45M05UC Stainless Steel Dishwasher

Installing model 665 kenmore dishwasher with granit counter top.The side bracket we are trying to use need to be snap of at the line to get dishwasher to fit right.The problem is we cant get to the screw the side of the washer is in the way and no hole is in the side of the washer.Need a real fix.


... Dishwashers

Screw drop Hi I was installing my new LG dishwasher and I droped a screw in the hole in the side panel where you can put a screw to connect to the side of your cabinet. There is a small plastic cover which I removed where you can screw a screw into the cabinet. However the head of my screw was too small and fell in the side panel. I can not get the screw out or see it now although I know it is in the dishwasher. Is there anyway of getting it out or will this cause a problem? Since it is in t


A great retrieving tool for this is a flexible shaft magnet wand. I strongly recommend this tool be placed in everyone's toolbox.\015\012\015\012as far as leaving it there if not found? probably safe from electrical. will years of vibration allow it ... LG 24 in. LD-12BS6 Stainless Steel Free-standing Dishwasher

Maytag jetclean dishwasher leaks: Water leaks underneath. I don't see the source of the leak but see water running out on the left side about midway back on the bottom. Could it be related to the little plug inside the unit on the left side halfway up?


... Dishwashers

We bought an aeg favorit 50674 dishwasher ,last week and yesterday i went to open the door to get the dishes out and the door wouldnt open.i tried again but noticed that it had caught on yhe side panel and was bending the panel.not wanting to make it worse i phoned the comit store that sold me the machine they said it was not their fault and wasnt covered on the warrenty .i still cant get my dishes out cant you help.thanks caz ivey


... AEG Dishwashers

My dishwasher is leaking from underneath, front left as you look at it. If i go underneath it, there appears to be a seal on the outside (it does not appear to be the one that runs along the bottom of the inside of the dishwasher) that has come away at one point. Do you know a) how to get the front panel off (the bit that makes it look built in),b) how can i get another one of these seals. I assume if i get one we can just fit it into place. Many thanks, Robyn J


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101\012\012\012p80897 ... Neff 24 in. S5453X1 Built-in Dishwasher

Bottom drawer cant get drawer out to get screws out from side walls


Look on the bottom side below the front. You will find two clips that can be pushed in to remove the drawer. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

My dishlex globale 300 has a modle no that is dx300wa*02 the eco light and pump keeps running i have recieved advice to drain/dryout the kidney shapped over flow tray but mine doesn't seem to have one. i've taken off the bottom cover to get a closer look but still can't see it i've also tried tipping the washer on it's left side right side,backside and even upside down to try and drain the extra water but that has made no difference please help


Hi,\015\012Try taking the dishwasher out of its wall space and tipping it back and forth. Apparently the weight of water gathering in some component triggers the 'eco' function. Allow it to evaporate by waiting for few days. ... Dishwashers

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

The door won't close. The latch seems jammed. I have tried setting and releasing the child lock inside the handle. The problem seems to be with the latch itself. From inside the door, I can see the tongue the clips into the latch, but it seems stuck. I can't get it to move, even with gentle force.


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

We have a 2 draw F & P dishwasher but at the end of a cycle the cups in the cup rack do not seem to be clean on the outside. We place the cups face down, the inside seems to get clean O.K. but there is a often a film left on the outside of the cup. What could be cuasing this?


If the problem does not get fixed by increasing the rinse aid quantity setting, and assuming you do not live in a hard water area, I would recommend buying a Finish dishwasher cleaning kit (2 pieces) and run dishwasher on high temperature cycle one d ... Fisher and Paykel 24 in. DD-602 Built-in Dishwasher

Thermal fuse Dishwasher konked out mid-cycle and now no power to control pad. We've already had the thermal fuse replaced once (machine is only 2 years old!) and this appears to be the same issue. I tried to open the front and I think I can see where it is but not sure how to get it out and replace it AGAIN. I wasn't able to get the inside panel completely apart from the front of the unit so I was somewhat limited. I'd rather save the service charge if I can and there's n


Http://www.partselect.com/MultiModels.aspx?ModelNum=KUDS35FXSS&SearchTerm=fuse&RefineSearch=0Maybe this link will help ... KitchenAid KUDS35FXSS Dishwasher

Baumatic BKD64W and BKD64SS rollers keep coming off inside dishwasher and cant get top rack in and out without much difficulty


... Dishwashers

When I open the dishwasher, I can see gunk on either side of the door. When the door is shut, these areas are covered up so of course they remain gunky. What is causing this? How do I get rid of it, clean it out? The only access to it is when the door is open.


This is semi normal, worse if people insist on putting food laden dishes in the dishwasher....\015\012\015\012Think about how food gets off ...... spraying water, and most particulate matter eventually falls to the pump area, but some mak ... GE Nautilus 24" Built-in Dishwasher

GE Quietpower 2 spray arms not rotating. Sounds like pump is working and water is moving inside but arms are still in same position when I check to see if they've moved. Of course the dishes don't get clean. What's up with this?


... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

Dishwasher is leaking from the lower right side, it appears as though it's leaking from inside of the outside cover (the metal part)if that makes any sense.


Hi,\012Here is a tip that I wrote about dishwashers and them leaking.Leaking Dishwasherheatman101 ... Frigidaire FDB1050REM Dishwasher

I get a film on the inside of dishwasher as well as dishes at the end of a cycle. You can really see the cloudy film on glasses. Dishwasher is only 18 months old.


Cloudy film is usually from hard water. Or it means the dishes arn't drying properly. you wanna make sure your using jet dry and that your not using liquid soap. Liquid soap is a killer of dishwashers and creates mineral deposits. If you have hard wa ... Kenmore Dishwashers

Amana dishwasher, model adb2200aws, ser #, 26650464e. history: quit running, no lights, nothing. replaced the door switch, ran for three days, replaced the switches on both sides of door switch, ran three days, quit. replaced the circuit panel , ran one time, quit. not lights, nothing. when I take it apart sometimes, that is take off inside cover on door, it might run or not. seems like the current isn't getting in as no lights will come one.


I have the same problem with mine as well but I found out that if you take a space heater to it and warm the control panel up for about 5 minutes, everything works great. This model of dishwasher seems to be problematic in any environment under 70-75 ... Amana Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1245 seconds