Having problems with your Dishwashers ?

The clean light is flashing, so nothing will run. how do you reset it?


Answers :

What is the clean light for? is it to clean the dish washer?
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Clean light is blinking, have already killed the power, then called to whirlpool and they walked me through resetting it by pushing buttons, however when i attempted to run it after resetting it, it started to run then went right back to the flashing clean light. i tried resetting it again, and ended up with the same result.


You may a a latching issue. d/w not latching properly. How long does it take before the clean light comes on after you reset it. does it fill with water? if so, then your motor may be defective. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Kenmore 665 17033400 Elite dishwasher clean light flashes 7 times and it wont run. i used the reset combination, all lights lit and stayed lit until i pressed reset. Then it started a wash. now the wash seems to be finished, though i am not sure and the clean light is flashing 7 times, pause, 7 times, etc.


That signals an issue with a faulty heater &/or heater drive circuit.(that info comes from their troubleshooting guide)I ran into it this weekend and discovered that the heater coil in the bottom of the washer was broken. ... Kenmore 24 in. 17032 Built-in Dishwasher

The clean light is flashing, so nothing will run. how do you reset it?


What is the clean light for? is it to clean the dish washer? ... Dishwashers

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

Whirlpool gold, quiet partner III, My dishwasher is not cleaning very well and when it is done it flashes clean. The clean flashing light wont stop. It flashes 7 times and stops for 3 sec then starts again. I know how to reset washer using heated dry and normal buttons but when i run it again when it is finished it goes back to the clean button flashing


... Whirlpool Dishwashers

Kenmore dishwasher Clean light flashes after reset goes through cycle but motor does not run then clean light comes on again.


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Whirlpool dishwasher Clean light is flashing which says check heat circuit. I've reset board a couple times and run diagnostic. Element tests okay. Light keeps going back to flashing when running dishwasher.


... Whirlpool DU1055XTS Built-in Dishwasher

The green clean light is flashing on my Kenmore Elite Ultra Wash dishwasher. After the reset sequence, the washer will run only 1 part of it's washing/drying cycle, then flash the clean light again... I have only owned it about 14 months, and this is the first problem I have had.


You may just need to reset your control board. Go to the link and it will explain how to reset the control board as well as explain what might cause the issue and how to fix it.http://www.appliancerepairlesson.com/dishwasher-2/dishwasher ... Kenmore 24 in. 17032 Built-in Dishwasher

The dishwasher will not run. The Clean light keeps flashing with 7 light intervals. When you press Cancel/Drain, the timer has 2 minutes and runs for 2 minutes. Not sure if it is drain since there is nothing to drain. Please help.


Hi\015\012\015\012If clean light\015\012is blinking 7 times then it may be an issue with heater circuit, door switch or\015\012wash pump. If yes then please reset the power to the dishwasher. After, 5\015\012minutes check if ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

My Frigidaire model FDBB2040FC3 ''acts'' like it starts running when I press start but after just a few moments the Start indicator light goes out and the Hi-Temp Wash and Air Dry lights start flashing... I can hear it ''running'' or doing something but it clearly isn't actually cleaning anything. I've tried cancelling, letting it reset itself and then restarting... even shut it off from the breaker. Each time the problem returns.


... Frigidaire Dishwashers

My Frigidaire model FDBB2040FC3 "acts" like it starts running when I press start but after just a few moments the Start indicator light goes out and the Hi-Temp Wash and Air Dry lights start flashing... I can hear it "running" or doing something but it clearly isn't actually cleaning anything. I've tried cancelling, letting it reset itself and then restarting... even shut it off from the breaker. Each time the problem returns. We're a family of 6 so our dishwasher is pretty important in this hou


... Frigidaire Dishwashers

Integrated ADG7560/2 dishwasher, the cancel light is flashing 8 times and I can see nothing in the filters. Every time I try to close it it does nothing but when open cancel button still flashing. Does anyone know how I reset it or how I get to the next level of filters to clean it? Many thanks


... Dishwashers

Miele g892 scu plus, about 5 years old. when on, all it does is run some motor (humming sound) and flash salt or intake/drain. No program lights on. Sometimes can be reset so rinse light comes on and nothing blinks, but humming motor still runs and salt eventually blinks. I removed toekick panel; there is water in pan. I disconnect drain hose, only a little water came out. Any ideas?


... Miele G892SC SS Dishwasher

I have a frididaire proffesional series aquasurge with speed clean dishwasher # PLD4375RFC3 dishwasher there is an Er code that just keeps flashing the china/crystal light is flashing as well as the low rinse light. it used to sound like it was running when you would close the door but nothing was happening inside. any ideas?


... Frigidaire 24 in. PLD3465REC Stainless Steel Built-in Dishwasher

Reset code I recently had a problem with my dishwasher that required me to use a reset code on my control panel. I can no longer find the manual that tells me that code. I was wondering if anyone knows it as to save a tech call. The error occurs when the clean light flashes. We have checked the heating element and the tech told us there is no problem there, we just need to reset the machine. The error has occured again, but this time because I tried to run the machine right when we came home fro


I believe the reset sequence is accomplished by pushing the NORMAL WASH then HEATED DRY buttons in that sequence two to three times. The unit will enter diagnostics mode, but can be stopped by pressing the CANCEL button. Let me know if this helps. ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

Have a NEFF S5453XOGB built in dishwasher - put it on last night and came down this morning and nothing has been cleaned and I have 2 red lines in the time display. HAve tried resetting by holding the 2 buttons down and switching on - it shows the number 23 - as sson as I let go the lights continue to flash and the number 1 appears. I am resetting it correctly?


... Neff 24 in. S5453X1 Built-in Dishwasher

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher

I have a kitchenaid KUDP01FL dishwasher. The clean light is flashing 7 times. I am not able to reset it and the dishwasher will not run. I would like to know the proper reset sequence and if that does not fix it what to try next.


... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

My kenmore dishwasher 665.17052400 clean light is flashing 7 times. I cannot locate the tech sheet to find out what is wrong. I have reset the panel and it will run then blink again after 15 mins or so. I have also done a hard reset and looked at the heating element, but it looks fine. Please help.


... Kenmore Dishwashers

The flashing light blinks 7 times on the clean indicator area , but the dishwasher will not function and when you press cancel it starts running but nothing washes through any cycle at all. please help


Ok well usually it is not sensing a temperature change in the water or\015\012not getting hot enough. so you can reset the dishwasher and try running\015\012the hot water in the sink before starting the dishwasher. if it fails\015\012again there is a ... KitchenAid Dishwashers

Green light flashes on clean. Will not run wash cycles. Will drain, Is there a reset button somewhere?


To reset your dishwasher, press the buttons [heated dry] [normal] [heated dry] [normal] to initiate the diagnostic cycle. This should clear the error message from the system and allow it to run again. If the problem persists, check the causes found h ... Kenmore 24 in. 17039 Built-in Dishwasher

Ive got a flashing clean light and the dishwasher won't run. Is there a reset button or a common part that causes this problem?


Flashing clean light on a Whirlpool dishwasher is a heater \015\012malfunction (sorta) this failure code is generated when the unit does \015\012not sense a 5 degree rise in water temperature with in 15 seconds (give \015\012or take depending on mode ... Whirlpool DU1055XTSQ Built-in Dishwasher

Kenmore Dishwasher model 665-13743k601 The clean light is flashing and will not reset. The dishwasher will not run.


Hi If clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. ... Kenmore Dishwashers

I have a Kenmore dishwasher 665.16022402 that is locked out at the board.( the clean light flashes continually & wont allow it to run) I don't have the manual to find the reset code and troubleshoot. There didn't seem to be any proublems till now.??????? any help?


... Kenmore 24 in. 16032 Built-in Dishwasher

Kenmore quietguard 7 dishwasher...clean light flashing, dishwasher won't run repair guy a few weeks ago couldn't come, but told my husband to push a couple of the buttons on the control panel, and it worked for a while... repair guy coming back on Monday, but I''d like to know the buttons to push to reset it so I can use it till then


... Kenmore 24 in. 15173 Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1532 seconds