Having problems with your Dishwashers ?

I have a Maytag Quiet Series 100 dishwasher. There is an icon with a "3" in it just to the left of "heat dry." I just noticed this "3" light is on and the dishwasher won't start when I push the "start/cancel" button. All that happens is the "3" light flashes when you push any of the other buttons, but it won't do anything else. Any help you can give me would be greatly appreciated. Thank you.


Answers :

The "3" means hold for 3 seconds to child proof it. When it's on, none of the functions work. When you hold it again for 3 seconds, it turns off and your buttons will work again.
\015\012Good luck!
Http://www.ehow.co.uk/how_6543387_troubleshoot-maytag-quiet-series-100.html\015\012\015\012\015\012
\015\012
\015\012http://www.ehow.co.uk/how_6284004_troubleshoot-maytag-dishwasher-not-fill.html\015\012
\015\012
\015\012Above are links to assist you to troubleshoot your issue. Below that is a link for your service manuals, use the manual to troubleshoot and isolate your issue.\015\012
\015\012I think error 3 is Will Not Drain.\015\012
\015\012Perhaps this fix below will apply, it may be worth a try?\015\012
\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing.
Now this happens because, the STOP Button, is pressed and the "Door Opened", during the Wash Cycle. This should NOT be done. You should NEVER TURN IT OFF MID-CYCLE. you should instead, Simply, pull on the handle, to Open the door, the system will take care of everything, after, you close it,and pick up where it left off. The turning OFF, makes the machine "Think" that a New Cycle, is going to be done, before the old one is finished, and resets itself to do it all again. But it still has water, that's not meant to be there so it must dump it out.
Now, the FIX. Take the Dishwasher, out, and tip over on it's side, tip to about a 45' angle. Water will come out from underneath, this is from a small "Overflow" reservoir. this reservoir has an "Anti-Flood" switch. The removing of this water will "Reset" this Switch, and allow the dishwasher to work again.
So what happens, is this, when the STOP button is pressed Mid-Cycle, the machine must "Dump" whatever water is still in the machine, into the "Overflow Reservoir". This water then causes the Anti-flood switch to jam, and this stops the machine, until it is reset,by the above method.
\015\012
\015\012http://appliancejunk.com/forums/index.php?topic=2945.0
Repair Help & Product Troubleshooting for Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher wont let u select a cycle...all buttons seem locked...ive unplugged it for 5 seconds or so and then plugged it back in and the normal wash button light comes on and the heated dry button light comes on, but it wont start and it doesnt respond when buttons are pushed...please help. thanks


... GE GLD4560NSS Stainless Steel Built-in Dishwasher

I have a Kitchen Aid dishwasher Model KUD1021RWH1 that is malfunctioning. The display has the Heavy Duty, Normal and Cancel lights all flashing on and off at the same time. This problem has been intermitent. The happens after we fill the washer and want it to start. I push the Normal button and the heavy duty button flashes with the normal button and the dishwasher wont start. So, I push the cancel button and it flashes also.The washer has been cycling fine since we bought it a few years ago unt


... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Electrolux dishwasher all lights blinking and wont turn on push start button either all lights flash or normal light stays on  either case the dishwasher wont run a cycle


Remove the toe kick by loosening 2 screws. There is a panel there with little lights that correspond to specific problems. The light that is on will correspond to the problem that the dishwasher has detected. Correct the problem and you should be goo ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

Hi i have a smeg df 410 sdx 450 wide dishwasher that is coming up to three years old ,the fault it has developed is that it wont switch on ,press the button and nothing happens,no lights or the normal beep.240v is getting to the button and when the button is pushed on 240v comes out the other side and goes to the various pcb's but the appliance wont do any thing,can you please give me some ideas.


... Dishwashers

I have a Kitchen aide dishwasher Model KUDI01ILWH6 that will not turn on..there is a control lock light on and I have tried pushing the cancel button but all that happens is the control lock light flashes 3 times and the dishwasher still wont turn on....Please , how to I disengage the control lock


... KitchenAid Dishwashers

Kenmore Elite Dishwasher, Model 665.15979992 No Heat Dry Button/Light: The dishwasher will not work. Have tried to no avail the various alternatives listed in this thread and others. Here's what the dishwasher is doing: To start off, the red light on the "No Heat/Dry" button is on - sometimes it's on steady; other times it blinks depending on whether other buttons have been pushed. Pushing any other button also causes the "Lock On" red light to come on. Pushing the "Cancel" button causes all


Have you checked the thermal cutoff switch located inside the door by doing a continuity test to it if this is sounding like where your problem are is coming from on this diagram ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

THe ProScrub light is steady, and the dishwasher does not work. When I push buttons, the light keeps going off, and with the next button push, it goes on. If I leave the dishwasher like this for a while, then a couple of the other lights, I think the Normal and Heated Dry lights will blink continuously. In either state, the dishwasher does not work.


... KitchenAid 24 in. KUDS02FR Built-in Dishwasher

Hi there. I'm having problems with my dishwasher. Usuaully once loaded, i push the start button, the closest green light to the start button flashes and dishwasher fills/cycle begins. Now, when i push the start button, the furthest green light from the start button flashes, you can hear the motor running but no cycle begins. No water fills the dishwasher.


... Hotpoint 23 in. BFV62 Built-in Dishwasher

Frigidare fdb1500lfco wont start. Heat dry light on and wont go off. Circuit breaker fine. Any ideas? No problems with dishwasher up til now. Pushed all buttons, nothing. No standing water.


Press and hold the heat dry button and it will turn off, so dishwasher is usable again. ... Frigidaire Dishwashers

My dishwasher Kenmore 665.13462k902 worked fine for a little over a year, now it wont even start. At first, the high temp button wouldnt light, then no lights until you pushed start...tonight, nothing works...any help?


... Kenmore Dishwashers

My dishwasher Kenmore 665.13462k902 worked fine for a little over a year, now it wont even start. At first, the high temp button wouldnt light, then no lights until you pushed start...tonight, nothing works...any help?


... Kenmore Dishwashers

My dishwasher 'start" button won't kick in. The machine seems to think it isn't locked - light wont activate, but the door IS locked. I select the cycle and option, but when i push start, it won't stay, The "clean" button keeps flashing. This is 5 years old


Hi,How many Blinks are there?Is it 7 Clean Light Blinks?Let me know, so that we could proceed.Hope i helped you.Thanks for using ' Fixya ' and have a nice day!! ... Kenmore 24 in. 17032 Built-in Dishwasher

Green clean light wont stop blinking unable to use dishwasher . It is an energy saver. the drain button works ..and when you push start the light comes on but will not run for cleaning


HiThanks for using FixYa. If the clean light flashes, pauses, and then repeats. When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean light fla ... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

My dishwasher wont run when i push the start / cancel button the washing light comes on and blinks ,but the dishwasher does not turn on . i put in a new control panel and it still does the same thing.


Check the water level switch/ pressure switch.Control panel may not have full control. There may be yet another board inside! ... Frigidaire Dishwashers

Matsui MF160 integrated dishwasher: Had problems for a while now with the buttons on the control panel ie: on button needed to be pressed down hard for it to connect and sometimes the wash cycle programme buttons would just keep flashing between the three of them and then they would settle down, for the past few days the on button light has stayed on and wont go off and now all the lights on the control panel have gone off and the dishwasher wont work at all, we have tried dis-connecting it, che


... Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

Have a kitchenaid dishwasher KUDS25SHWH1 - the child-lock light came on and will not go off. It is a light and no button to push and hold except all of the select buttons for the type of wash you want, no air dry button. How do I get this light off?? The Child Lock light has come on by it's self and I cannot get it to turn off. I have never used this feature before. I have tried to hold the Energy Saver button for several seconds but the Child Lock light will not shut off. The dishwasher is loc


Unplug the unit for 15 minutes then plug it back in. This should reset all your computer system and make everything work again ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

I have an LG dishwasher Model LD-O5AW2 Benchtop. IT has been going perfectly until now. I push the button in and then the start button, when the wash cycle has finnished it wont empty until I push the stop button off and then on again. Then it empties and goes to rinse but wont come out of the rinse cycle, just keeps rinsing, until I turn it off and on again.Up until now its been a great little dishwasher. JOAN


... LG Dishwashers

ADB1500AWB WILL NOT TURN ON & RUN. There is power to the dishwasher, but when you push the ON or RUN button on the door it will not run. The push buttons seem to be working, but with a faint light rather than the bright light when it use to run. These lights are only on while I push and hold the on button. Thanks for the help.


... Amana Dishwashers

ADB1500AWB WILL NOT TURN ON & RUN. There is power to the dishwasher, but when you push the ON or RUN button on the door it will not run. The push buttons seem to be working, but with a faint light rather than the bright light when it use to run. These lights are only on while I push and hold the on button. Thanks for the help.


... Amana Dishwashers

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

Lock Control I don't have a manual for my dishwasher. The Lock button is on (top of dishwasher). I have pushed that top button for 3 seconds. The button on the top and the "L" then both blink. The button on the top then stays on and the "L" light goes off. Since I can't get the lock light to go off - - my dishwasher won't tun on. Thank you very much.


First try unplugging the washer from powerpoint for 30secs..this may disable lock.if not, some washers will still work on lock if you hold the buttons you need. for 5seconds. eg try starting washer as normal but hold the button for 5secs....(Ps you m ... Jenn-Air 24 in. JDB1050AW Free-standing Dishwasher

I have a Maytag Quiet Series 100 dishwasher. There is an icon with a "3" in it just to the left of "heat dry." I just noticed this "3" light is on and the dishwasher won't start when I push the "start/cancel" button. All that happens is the "3" light flashes when you push any of the other buttons, but it won't do anything else. Any help you can give me would be greatly appreciated. Thank you.


The "3" means hold for 3 seconds to child proof it. When it's on, none of the functions work. When you hold it again for 3 seconds, it turns off and your buttons will work again.\015\012Good luck! ... Dishwashers

My dishwasher whirlpool model GU1200XTLS3 wont start. When I push the nomal wash button, it will light up for a few seconds then off and nothing happen. Please help!


... Whirlpool GU1200XTLS Stainless Steel Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1920 seconds